Messages in this thread | | | From | Art <> | Subject | PROBLEM: kernel module "via-ircc" problem in 2.4.26 but not in 2.6.5 | Date | Mon, 24 May 2004 01:37:58 +0200 |
| |
[1.] One line summary of the problem: The module via-ircc prints error message on 2.4.25 and 2.4.26 kernels but not on 2.6.6-mm4 and vanilla 2.6.5.
[2.] Full description of the problem/report: When I do "insmod via-ircc" I get: --start-- Using /lib/modules/2.4.25-gentoo-r2/kernel/drivers/net/irda/via-ircc.o /lib/modules/2.4.25-gentoo-r2/kernel/drivers/net/irda/via-ircc.o: /lib/modules/2.4.25-gentoo-r2/kernel/drivers/net/irda/via-ircc.o: unresolved symbol irlap_open_R1698cb30 /lib/modules/2.4.25-gentoo-r2/kernel/drivers/net/irda/via-ircc.o: /lib/modules/2.4.25-gentoo-r2/kernel/drivers/net/irda/via-ircc.o: unresolved symbol irda_device_setup_Rd786063a /lib/modules/2.4.25-gentoo-r2/kernel/drivers/net/irda/via-ircc.o: /lib/modules/2.4.25-gentoo-r2/kernel/drivers/net/irda/via-ircc.o: unresolved symbol irda_qos_bits_to_value_R448b8aaa /lib/modules/2.4.25-gentoo-r2/kernel/drivers/net/irda/via-ircc.o: /lib/modules/2.4.25-gentoo-r2/kernel/drivers/net/irda/via-ircc.o: unresolved symbol irda_device_txqueue_empty_R548f6833 /lib/modules/2.4.25-gentoo-r2/kernel/drivers/net/irda/via-ircc.o: /lib/modules/2.4.25-gentoo-r2/kernel/drivers/net/irda/via-ircc.o: unresolved symbol setup_dma_R01485953 /lib/modules/2.4.25-gentoo-r2/kernel/drivers/net/irda/via-ircc.o: /lib/modules/2.4.25-gentoo-r2/kernel/drivers/net/irda/via-ircc.o: unresolved symbol irda_device_set_media_busy_R51331c3a /lib/modules/2.4.25-gentoo-r2/kernel/drivers/net/irda/via-ircc.o: /lib/modules/2.4.25-gentoo-r2/kernel/drivers/net/irda/via-ircc.o: unresolved symbol irda_init_max_qos_capabilies_R6b043eba /lib/modules/2.4.25-gentoo-r2/kernel/drivers/net/irda/via-ircc.o: /lib/modules/2.4.25-gentoo-r2/kernel/drivers/net/irda/via-ircc.o: unresolved symbol irda_debug_R07c03e02 /lib/modules/2.4.25-gentoo-r2/kernel/drivers/net/irda/via-ircc.o: /lib/modules/2.4.25-gentoo-r2/kernel/drivers/net/irda/via-ircc.o: unresolved symbol async_wrap_skb_R8738243f /lib/modules/2.4.25-gentoo-r2/kernel/drivers/net/irda/via-ircc.o: /lib/modules/2.4.25-gentoo-r2/kernel/drivers/net/irda/via-ircc.o: unresolved symbol irlap_close_Rd8bd2ed6 --end-- I also get a similar error message with 2.4.26 but not with 2.6.6-mm4 and 2.6.5.
[3.] Keywords (i.e., modules, networking, kernel): modules, irda, via-ircc
[4.] Kernel version (from /proc/version): Linux version 2.4.25-gentoo-r2 (root@xmobile) (gcc version 3.3.3 20040412 (Gentoo Linux 3.3.3-r5, ssp-3.3-7, pie-8.7.5.3)) #1 Sun May 23 21:37:29 CEST 2004
[5.] Output of Oops.. message (if applicable) with symbolic information resolved (see Documentation/oops-tracing.txt) -
[6.] A small shell script or example program which triggers the problem (if possible) insmod via-ircc
[7.] Environment Gentoo Linux running 2.4.25-gentoo-r2 kernel.
[7.1.] Software (add the output of the ver_linux script here) --start-- If some fields are empty or look unusual you may have an old version. Compare to the current minimal requirements in Documentation/Changes.
Linux xmobile 2.4.25-gentoo-r2 #1 Sun May 23 21:37:29 CEST 2004 i686 Mobile Intel(R) Pentium(R) 4 - M CPU 2.00GHz GenuineIntel GNU/Linux
Gnu C 3.3.3 Gnu make 3.80 util-linux 2.12 mount 2.12 modutils 2.4.26 e2fsprogs 1.35 jfsutils 1.1.5 xfsprogs 2.6.3 pcmcia-cs 3.2.7 PPP 2.4.2 Linux C Library 2.3.3 head: `-1' option is obsolete; use `-n 1' since this will be removed in the future Dynamic linker (ldd) 2.3.3 Procps 3.2.1 Net-tools 1.60 Kbd 1.12 Sh-utils 5.2.1 Modules Loaded nvidia mousedev usbmouse yenta_socket pcmcia_core ohci1394 ieee1394 via-rhine mii nls_iso8859-15 ntfs coda button fan battery ac thermal processor sr_mod sg ide-scsi scsi_mod hid uhci ehci-hcd usbcore --end--
[7.2.] Processor information (from /proc/cpuinfo): --start-- processor : 0 vendor_id : GenuineIntel cpu family : 15 model : 2 model name : Mobile Intel(R) Pentium(R) 4 - M CPU 2.00GHz stepping : 7 cpu MHz : 1990.249 cache size : 512 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe bogomips : 3971.48 --end--
[7.3.] Module information (from /proc/modules): --start-- nvidia 1965952 7 (autoclean) mousedev 4340 1 usbmouse 2232 0 (unused) yenta_socket 10880 0 pcmcia_core 46948 0 [yenta_socket] ohci1394 25552 0 (unused) ieee1394 47620 0 [ohci1394] via-rhine 12944 1 mii 2512 0 [via-rhine] nls_iso8859-15 3356 4 (autoclean) ntfs 77388 4 (autoclean) coda 43524 0 (unused) button 2540 0 (unused) fan 1632 0 (unused) battery 5120 0 (unused) ac 1792 0 (unused) thermal 6276 0 (unused) processor 8344 0 [thermal] sr_mod 13976 0 (unused) sg 28860 0 (unused) ide-scsi 10192 0 scsi_mod 84160 3 [sr_mod sg ide-scsi] hid 21248 0 (unused) uhci 26188 0 (unused) ehci-hcd 18948 0 (unused) usbcore 63404 1 [usbmouse hid uhci ehci-hcd] --end--
[7.4.] Loaded driver and hardware information (/proc/ioports, /proc/iomem) --start--(ioports)-- 0000-001f : dma1 0020-003f : pic1 0040-005f : timer 0060-006f : keyboard 0070-007f : rtc 0080-008f : dma page reg 00a0-00bf : pic2 00c0-00df : dma2 00f0-00ff : fpu 0170-0177 : ide1 01f0-01f7 : ide0 0376-0376 : ide1 03c0-03df : vesafb 03f6-03f6 : ide0 0cf8-0cff : PCI conf1 1000-10ff : VIA Technologies, Inc. VT8233/A/8235 AC97 Audio Controller 4000-40ff : PCI CardBus #02 4400-44ff : PCI CardBus #02 d000-d0ff : VIA Technologies, Inc. VT6102 [Rhine-II] d000-d0ff : via-rhine d400-d41f : VIA Technologies, Inc. USB (#3) d400-d41f : usb-uhci d800-d81f : VIA Technologies, Inc. USB (#4) d800-d81f : usb-uhci e000-e0ff : VIA Technologies, Inc. Intel 537 [AC97 Modem] e400-e47f : VIA Technologies, Inc. IEEE 1394 Host Controller e800-e81f : VIA Technologies, Inc. USB e800-e81f : usb-uhci ec00-ec1f : VIA Technologies, Inc. USB (#2) ec00-ec1f : usb-uhci fc00-fc0f : VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE fc00-fc07 : ide0 fc08-fc0f : ide1 --end--
--start--(iomem) 00000000-0009fbff : System RAM 0009fc00-0009ffff : reserved 000a0000-000bffff : Video RAM area 000c0000-000c7fff : Video ROM 000d0000-000d3fff : reserved 000f0000-000fffff : System ROM 00100000-27feffff : System RAM 001a6000-00416241 : Kernel code 27ff0000-27ff7fff : ACPI Tables 27ff8000-27ffffff : ACPI Non-volatile Storage 28000000-28000fff : Texas Instruments PCI1410 PC card Cardbus Controller 28400000-287fffff : PCI CardBus #02 28800000-28bfffff : PCI CardBus #02 cdb00000-ddcfffff : PCI Bus #01 d0000000-d7ffffff : nVidia Corporation NV17 [GeForce4 440 Go 64M] d0000000-d02fffff : vesafb ddc80000-ddcfffff : nVidia Corporation NV17 [GeForce4 440 Go 64M] dde00000-dfefffff : PCI Bus #01 de000000-deffffff : nVidia Corporation NV17 [GeForce4 440 Go 64M] dffff000-dffff7ff : VIA Technologies, Inc. IEEE 1394 Host Controller dffff000-dffff7ff : ohci1394 dffffe00-dffffeff : VIA Technologies, Inc. VT6102 [Rhine-II] dffffe00-dffffeff : via-rhine dfffff00-dfffffff : VIA Technologies, Inc. USB 2.0 dfffff00-dfffffff : ehci_hcd e0000000-e3ffffff : VIA Technologies, Inc. VT8753 [P4X266 AGP] fff80000-ffffffff : reserved --end--
[7.5.] PCI information ('lspci -vvv' as root) --start-- pcilib: Cannot open /sys/bus/pci/devices 0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8753 [P4X266 AGP] (rev 01) Subsystem: VIA Technologies, Inc.: Unknown device 0000 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+ Latency: 8 Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M] Capabilities: [a0] AGP version 2.0 Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4 Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none> Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8633 [Apollo Pro266 AGP] (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: dde00000-dfefffff Prefetchable memory behind bridge: cdb00000-ddcfffff BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B- Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:03.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus Controller (rev 02) Subsystem: TWINHEAD INTERNATIONAL Corp: Unknown device 0603 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 168, cache line size 20 Interrupt: pin A routed to IRQ 5 Region 0: Memory at 28000000 (32-bit, non-prefetchable) [size=4K] Bus: primary=00, secondary=02, subordinate=05, sec-latency=176 Memory window 0: 28400000-287ff000 (prefetchable) Memory window 1: 28800000-28bff000 I/O window 0: 00004000-000040ff I/O window 1: 00004400-000044ff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+ 16-bit legacy interface ports at 0001
0000:00:07.0 USB Controller: VIA Technologies, Inc. USB (rev 50) (prog-if 00 [UHCI]) Subsystem: TWINHEAD INTERNATIONAL Corp: Unknown device c902 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, cache line size 08 Interrupt: pin A routed to IRQ 10 Region 4: I/O ports at e800 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:07.1 USB Controller: VIA Technologies, Inc. USB (rev 50) (prog-if 00 [UHCI]) Subsystem: TWINHEAD INTERNATIONAL Corp: Unknown device c902 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, cache line size 08 Interrupt: pin B routed to IRQ 10 Region 4: I/O ports at ec00 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:07.2 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 51) (prog-if 20 [EHCI]) Subsystem: TWINHEAD INTERNATIONAL Corp: Unknown device c902 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, cache line size 20 Interrupt: pin C routed to IRQ 10 Region 0: Memory at dfffff00 (32-bit, non-prefetchable) [size=256] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:0a.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 46) (prog-if 10 [OHCI]) Subsystem: Unknown device ff14:02c7 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (8000ns max), cache line size 08 Interrupt: pin A routed to IRQ 5 Region 0: Memory at dffff000 (32-bit, non-prefetchable) [size=2K] Region 1: I/O ports at e400 [size=128] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8233 PCI to ISA Bridge Subsystem: VIA Technologies, Inc.: Unknown device 0000 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP]) Subsystem: TWINHEAD INTERNATIONAL Corp: Unknown device 1203 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 Interrupt: pin A routed to IRQ 255 Region 4: I/O ports at fc00 [size=16] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:11.2 USB Controller: VIA Technologies, Inc. USB (rev 23) (prog-if 00 [UHCI]) Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, cache line size 08 Interrupt: pin D routed to IRQ 10 Region 4: I/O ports at d400 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:11.3 USB Controller: VIA Technologies, Inc. USB (rev 23) (prog-if 00 [UHCI]) Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, cache line size 08 Interrupt: pin D routed to IRQ 10 Region 4: I/O ports at d800 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235 AC97 Audio Controller (rev 30) Subsystem: TWINHEAD INTERNATIONAL Corp: Unknown device 0403 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin C routed to IRQ 5 Region 0: I/O ports at 1000 [size=256] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:11.6 Communication controller: VIA Technologies, Inc. Intel 537 [AC97 Modem] (rev 70) Subsystem: TWINHEAD INTERNATIONAL Corp: Unknown device 1005 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin C routed to IRQ 5 Region 0: I/O ports at e000 [size=256] Capabilities: [d0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 70) Subsystem: TWINHEAD INTERNATIONAL Corp: Unknown device 0204 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (750ns min, 2000ns max), cache line size 08 Interrupt: pin A routed to IRQ 10 Region 0: I/O ports at d000 [size=256] Region 1: Memory at dffffe00 (32-bit, non-prefetchable) [size=256] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:01:00.0 VGA compatible controller: nVidia Corporation NV17 [GeForce4 440 Go 64M] (rev a3) (prog-if 00 [VGA]) Subsystem: TWINHEAD INTERNATIONAL Corp: Unknown device 030b Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 248 (1250ns min, 250ns max) Interrupt: pin A routed to IRQ 11 Region 0: Memory at de000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at d0000000 (32-bit, prefetchable) [size=128M] Region 2: Memory at ddc80000 (32-bit, prefetchable) [size=512K] Expansion ROM at dfee0000 [disabled] [size=128K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [44] AGP version 2.0 Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4 Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none> --end--
[7.6.] SCSI information (from /proc/scsi/scsi) Kernelparameter: hdc=ide-scsi --start-- Attached devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: QSI Model: CDRW/DVD SBW-241 Rev: VK02 Type: CD-ROM ANSI SCSI revision: 02 --end--
[7.7.] Other information that might be relevant to the problem (please look in /proc and include all information that you think to be relevant): -
[X.] Other notes, patches, fixes, workarounds: I took the via-ircc.h and via-ircc.h from 2.6.6-mm4 and copied over the via-ircc.h and via-ircc.c from the vanilla 2.4.26 kernel, but insmod failed with a different error. - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |