Messages in this thread | | | Date | Thu, 22 Apr 2004 07:48:03 -0700 (PDT) | Subject | Kernel 2.4.26 Hangs During Boot | From | "Norman Zhang" <> |
| |
Hi,
I compiled kernel-2.4.26 with
# make xconfig # make dep # make bzImage # make modules # make modules_install # make install
But when I booted the new kernel, I get a complete freeze with no errors or warnings. However IDE disk does spins for awhile. When I rebooted my old kernel, it complains disk corruption. I'm not sure if it is IDE bug. Would someone please give me a few pointers here? I've attached lspci, dmesg, and config below.
Thanks and Regards, Norman
Linux version 2.4.25-2mdk (nplanel@no.mandrakesoft.com) (gcc version 3.3.2 (Mandrake Linux 10.0 3.3.2-6mdk)) #1 Tue Mar 2 07:39:08 CET 2004 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 0000000022000000 (usable) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) 544MB LOWMEM available. ACPI: have wakeup address 0xc0001000 On node 0 totalpages: 139264 zone(0): 4096 pages. zone(1): 135168 pages. zone(2): 0 pages. ACPI: Unable to locate RSDP Building zonelist for node : 0 Kernel command line: BOOT_IMAGE=2425-2 ro root=305 noapic devfs=mount acpi=ht resume=/dev/hda6 splash=silent bootsplash: silent mode. Local APIC disabled by BIOS -- reenabling. Found and enabled local APIC! Initializing CPU#0 Detected 300.687 MHz processor. Console: colour dummy device 80x25 Calibrating delay loop... 599.65 BogoMIPS Memory: 547064k/557056k available (1603k kernel code, 9604k reserved, 1240k data, 144k init, 0k highmem, 0k BadRAM) Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) Inode cache hash table entries: 65536 (order: 7, 524288 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer cache hash table entries: 32768 (order: 5, 131072 bytes) Page-cache hash table entries: 262144 (order: 8, 1048576 bytes) CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 512K Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: After generic, caps: 0183fbff 00000000 00000000 00000000 CPU: Common caps: 0183fbff 00000000 00000000 00000000 CPU: Intel Pentium II (Deschutes) stepping 02 Enabling fast FPU save and restore... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX enabled ExtINT on CPU#0 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 300.6893 MHz. ..... host bus clock speed is 66.8198 MHz. cpu: 0, clocks: 668198, slice: 334099 CPU0<T0:668192,T1:334080,D:13,S:334099,C:668198> mtrr: v1.41 (20040107) Richard Gooch (rgooch@atnf.csiro.au) mtrr: detected mtrr type: Intel ACPI: Subsystem revision 20040116 ACPI: Interpreter disabled. PCI: PCI BIOS revision 2.10 entry at 0xfb350, last bus=1 PCI: Using configuration type 1 PCI: Probing PCI hardware PCI: ACPI tables contain no PCI IRQ routing entries PCI: Probing PCI hardware (bus 00) PCI: Using IRQ router PIIX/ICH [8086/7110] at 00:07.0 Limiting direct PCI/PCI transfers. isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16) Software Suspend Gzip Compression Driver v1.0 Software Suspend LZF Compression Driver v1.0 Software Suspend Swap Writer v1.0 Starting kswapd kinoded started VFS: Disk quotas vdquot_6.5.1 devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x1 vesafb: framebuffer at 0xe4000000, mapped to 0xe2800000, size 1875k vesafb: mode is 800x600x16, linelength=1600, pages=7 vesafb: protected mode interface info at c000:4785 vesafb: scrolling: redraw vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0 Looking for splash picture.... silenjpeg size 14856 bytes, found (800x600, 14808 bytes, v3). Got silent jpeg. Got silent jpeg. Console: switching to colour frame buffer device 92x32 fb0: VESA VGA frame buffer device pty: 1024 Unix98 ptys configured Serial driver version 5.1-alpha (2004-01-01) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx PIIX4: IDE controller at PCI slot 00:07.1 PIIX4: chipset revision 1 PIIX4: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:pio hda: C/H/S=1024/16/255 from BIOS ignored hda: WDC WD400JB-00ENA0, ATA DISK drive blk: queue c0444ac0, I/O limit 4095Mb (mask 0xffffffff) hdc: CD-956B, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 hda: attached ide-disk driver. hda: host protected area => 1 hda: 78165360 sectors (40021 MB) w/8192KiB Cache, CHS=77545/16/63, UDMA(33) Partition check: /dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 p9 p10 > ide: late registration of driver. md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. Initializing Cryptographic API NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 4096 buckets, 32Kbytes TCP: Hash tables configured (established 262144 bind 65536) Linux IP multicast router 0.06 plus PIM-SM NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. SoftwareSuspend2: Swapwriter: Image location doesn't begin with 'swap:'<1>Swsusp 2.0-rc4: Missing or invalid storage location (resume2= parameter). Please correct and rerun lilo (or equivalent) before suspending. Swsusp 2.0-rc4: kswsuspd starting RAMDISK: Compressed image found at block 0 Freeing initrd memory: 121k freed VFS: Mounted root (ext2 filesystem). Mounted devfs on /dev Journalled Block Device driver loaded kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. Mounted devfs on /dev Freeing unused kernel memory: 144k freed Real Time Clock Driver v1.10f usb.c: registered new driver usbdevfs usb.c: registered new driver hub usb-uhci.c: $Revision: 1.275 $ time 07:52:37 Mar 2 2004 usb-uhci.c: High bandwidth mode enabled PCI: Found IRQ 11 for device 00:07.2 PCI: Sharing IRQ 11 with 00:09.0 usb-uhci.c: USB UHCI at I/O 0x6400, IRQ 11 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 2 ports detected usb-uhci.c: v1.275:USB Universal Host Controller Interface driver usbdevfs: remount parameter error EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,5), internal journal Adding Swap: 1023584k swap-space (priority -1) SCSI subsystem driver Revision: 1.00 imm: Version 2.05 (for Linux 2.4.0) imm: parport reports no devices. SCSI subsystem driver Revision: 1.00 ppa: Version 2.07 (for Linux 2.4.x) ppa: parport reports no devices. kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,1), internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,9), internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,10), internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,7), internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,8), internal journal EXT3-fs: mounted filesystem with ordered data mode. sundance.c:v1.01+LK1.09a 10-Jul-2003 Written by Donald Becker http://www.scyld.com/network/sundance.html PCI: Found IRQ 11 for device 00:09.0 PCI: Sharing IRQ 11 with 00:07.2 eth0: D-Link DFE-530TXS FAST Ethernet Adapter at 0x6800, 00:05:5d:ff:59:93, IRQ 11. eth0: MII PHY found at address 1, status 0x782d advertising 01e1. PCI: Found IRQ 10 for device 00:0a.0 eth1: D-Link DFE-530TXS FAST Ethernet Adapter at 0x6c00, 00:05:5d:ff:1e:4f, IRQ 10. eth1: MII PHY found at address 1, status 0x7809 advertising 01e1. ip_conntrack version 2.1 (4352 buckets, 34816 max) - 320 bytes per conntrack ip_tables: (C) 2000-2002 Netfilter core team ip_tables: (C) 2000-2002 Netfilter core team ip_conntrack version 2.1 (4352 buckets, 34816 max) - 320 bytes per conntrack inserting floppy driver for 2.4.25-2mdk Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 hdc: attached ide-cdrom driver. hdc: ATAPI 40X CD-ROM drive, 128kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.12 eth0: Link changed: 100Mbps, full duplex Looking for splash picture.... found (800x600, 11943 bytes, v3). Splash status on console 0 changed to on Looking for splash picture.... found (800x600, 11943 bytes, v3). Splash status on console 1 changed to on Looking for splash picture.... found (800x600, 11943 bytes, v3). Splash status on console 2 changed to on Looking for splash picture.... found (800x600, 11943 bytes, v3). Splash status on console 3 changed to on Looking for splash picture.... found (800x600, 11943 bytes, v3). Splash status on console 4 changed to on Looking for splash picture.... found (800x600, 11943 bytes, v3). Splash status on console 5 changed to on application bug: crond(2690) has SIGCHLD set to SIG_IGN but calls wait(). (see the NOTES section of 'man 2 wait'). Workaround activated. application bug: crond(4205) has SIGCHLD set to SIG_IGN but calls wait(). (see the NOTES section of 'man 2 wait'). Workaround activated. application bug: crond(4214) has SIGCHLD set to SIG_IGN but calls wait(). (see the NOTES section of 'man 2 wait'). Workaround activated. application bug: crond(4223) has SIGCHLD set to SIG_IGN but calls wait(). (see the NOTES section of 'man 2 wait'). Workaround activated. application bug: crond(4232) has SIGCHLD set to SIG_IGN but calls wait(). (see the NOTES section of 'man 2 wait'). Workaround activated. application bug: crond(4241) has SIGCHLD set to SIG_IGN but calls wait(). (see the NOTES section of 'man 2 wait'). Workaround activated. application bug: crond(4250) has SIGCHLD set to SIG_IGN but calls wait(). (see the NOTES section of 'man 2 wait'). Workaround activated. application bug: crond(9883) has SIGCHLD set to SIG_IGN but calls wait(). (see the NOTES section of 'man 2 wait'). Workaround activated. application bug: crond(9892) has SIGCHLD set to SIG_IGN but calls wait(). (see the NOTES section of 'man 2 wait'). Workaround activated.00:00.0 Host bridge: Intel Corp. 440LX/EX - 82443LX/EX Host bridge (rev 03) 00:01.0 PCI bridge: Intel Corp. 440LX/EX - 82443LX/EX AGP bridge (rev 03) 00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02) 00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) 00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) 00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02) 00:09.0 Ethernet controller: D-Link System Inc DL10050 Sundance Ethernet (rev 12) 00:0a.0 Ethernet controller: D-Link System Inc DL10050 Sundance Ethernet (rev 12) 00:0b.0 Multimedia audio controller: Ensoniq ES1370 [AudioPCI] 01:00.0 VGA compatible controller: ATI Technologies Inc 3D Rage Pro AGP 1X/2X (rev 5c)[unhandled content-type:application/octet-stream] | |