lkml.org 
[lkml]   [2004]   [Dec]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Subject[patch] scsi/libata: correct bug for ULi M5281
From
Date

Hi, Jeff

The sata_uli patch for m5281 looks fine,but some of M5281 chip's PHY
is not stable sometime, so it need a workaround to correct the bug.

patch_M5281workaround is just for it.

The patch is applied to kernel 2.6.9. Pleases apply to new kernels, thanks
a lot.

Signed-off-by: Clear Zhang <Clear.Zhang@uli.com.tw>
Thanks (See attached file: patch_M5281workaround)
Clear




Jeff Garzik
<jgarzik@pobox.c 收件人: Clear.Zhang@uli.com.tw
om> 抄送: Peer.Chen@uli.com.tw, Emily.Jiang@uli.com.tw, Eric.Lo@uli.com.tw
主题: Re: [patch] net/tulip: Add support for ULi M526X
2004-11-17 05:12





The patch format looks good. I will review and apply, thanks.

BTW, I just merged support for 5281 SATA.

The email containing this patch is attached. This will appear in Linux
kernel 2.4.29 and 2.6.11.

Regards,

Jeff




-----来自 Jeff Garzik <jgarzik@pobox.com> 的消息,在 Tue, 16 Nov 2004
02:21:31 -0500 -----
收件人: linux-ide@vger.kernel.org

抄送: linux-kernel@vger.kernel.org

主题: [PATCH] ULi SATA fixes, new support




Another one just checked into libata-dev-2.6.


drivers/scsi/sata_uli.c | 51
+++++++++++++++++++++---------------------------
1 files changed, 23 insertions(+), 28 deletions(-)
through these ChangeSets:

<jgarzik@pobox.com> (04/11/16 1.2169)
[libata sata_uli] add 5281 support, fix SATA phy setup for others

Contributed by Peer Chen @ ULi and tested by a user.

diff -Nru a/drivers/scsi/sata_uli.c b/drivers/scsi/sata_uli.c
--- a/drivers/scsi/sata_uli.c 2004-11-16 02:19:58 -05:00
+++ b/drivers/scsi/sata_uli.c 2004-11-16 02:19:58 -05:00
@@ -32,16 +32,18 @@
#include <linux/libata.h>

#define DRV_NAME "sata_uli"
-#define DRV_VERSION "0.2"
+#define DRV_VERSION "0.5"

enum {
uli_5289 = 0,
uli_5287 = 1,
+ uli_5281 = 2,

/* PCI configuration registers */
- ULI_SCR_BASE = 0x90, /* sata0 phy SCR
registers */
- ULI_SATA1_OFS = 0x10, /* offset from
sata0->sata1 phy regs */
-
+ ULI5287_BASE = 0x90, /* sata0 phy SCR
registers */
+ ULI5287_OFFS = 0x10, /* offset from
sata0->sata1 phy regs */
+ ULI5281_BASE = 0x60, /* sata0 phy SCR
registers */
+ ULI5281_OFFS = 0x60, /* offset from
sata0->sata1 phy regs */
};

static int uli_init_one (struct pci_dev *pdev, const struct pci_device_id
*ent);
@@ -51,6 +53,7 @@
static struct pci_device_id uli_pci_tbl[] = {
{ PCI_VENDOR_ID_AL, 0x5289, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
uli_5289 },
{ PCI_VENDOR_ID_AL, 0x5287, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
uli_5287 },
+ { PCI_VENDOR_ID_AL, 0x5281, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
uli_5281 },
{ } /* terminate list */
};

@@ -125,33 +128,15 @@
MODULE_DEVICE_TABLE(pci, uli_pci_tbl);
MODULE_VERSION(DRV_VERSION);

-static unsigned int get_scr_cfg_addr(unsigned int port_no, unsigned int
sc_reg)
+static unsigned int get_scr_cfg_addr(struct ata_port *ap, unsigned int
sc_reg)
{
- unsigned int addr = ULI_SCR_BASE + (4 * sc_reg);
-
- switch (port_no) {
- case 0:
- break;
- case 1:
- addr += ULI_SATA1_OFS;
- break;
- case 2:
- addr += ULI_SATA1_OFS*4;
- break;
- case 3:
- addr += ULI_SATA1_OFS*5;
- break;
- default:
- BUG();
- break;
- }
- return addr;
+ return ap->ioaddr.scr_addr + (4 * sc_reg);
}

static u32 uli_scr_cfg_read (struct ata_port *ap, unsigned int sc_reg)
{
struct pci_dev *pdev = to_pci_dev(ap->host_set->dev);
- unsigned int cfg_addr = get_scr_cfg_addr(ap->port_no, sc_reg);
+ unsigned int cfg_addr = get_scr_cfg_addr(ap, sc_reg);
u32 val;

pci_read_config_dword(pdev, cfg_addr, &val);
@@ -161,7 +146,7 @@
static void uli_scr_cfg_write (struct ata_port *ap, unsigned int scr, u32
val)
{
struct pci_dev *pdev = to_pci_dev(ap->host_set->dev);
- unsigned int cfg_addr = get_scr_cfg_addr(ap->port_no, scr);
+ unsigned int cfg_addr = get_scr_cfg_addr(ap, scr);

pci_write_config_dword(pdev, cfg_addr, val);
}
@@ -222,9 +207,11 @@
rc = -ENOMEM;
goto err_out_regions;
}
-
+
switch (board_idx) {
case uli_5287:
+ probe_ent->port[0].scr_addr = ULI5287_BASE;
+ probe_ent->port[1].scr_addr = ULI5287_BASE +
ULI5287_OFFS;
probe_ent->n_ports = 4;

probe_ent->port[2].cmd_addr =
pci_resource_start(pdev, 0) + 8;
@@ -232,19 +219,27 @@
probe_ent->port[2].ctl_addr =
(pci_resource_start(pdev, 1) |
ATA_PCI_CTL_OFS) + 4;
probe_ent->port[2].bmdma_addr =
pci_resource_start(pdev, 4) + 16;
+ probe_ent->port[2].scr_addr = ULI5287_BASE +
ULI5287_OFFS*4;

probe_ent->port[3].cmd_addr =
pci_resource_start(pdev, 2) + 8;
probe_ent->port[3].altstatus_addr =
probe_ent->port[3].ctl_addr =
(pci_resource_start(pdev, 3) |
ATA_PCI_CTL_OFS) + 4;
probe_ent->port[3].bmdma_addr =
pci_resource_start(pdev, 4) + 24;
+ probe_ent->port[3].scr_addr = ULI5287_BASE +
ULI5287_OFFS*5;

ata_std_ports(&probe_ent->port[2]);
ata_std_ports(&probe_ent->port[3]);
break;

case uli_5289:
- /* do nothing; ata_pci_init_native_mode did it all
*/
+ probe_ent->port[0].scr_addr = ULI5287_BASE;
+ probe_ent->port[1].scr_addr = ULI5287_BASE +
ULI5287_OFFS;
+ break;
+
+ case uli_5281:
+ probe_ent->port[0].scr_addr = ULI5281_BASE;
+ probe_ent->port[1].scr_addr = ULI5281_BASE +
ULI5281_OFFS;
break;

default:





[unhandled content-type:application/octet-stream]
\
 
 \ /
  Last update: 2005-03-22 14:08    [from the cache]
©2003-2011 Jasper Spaans