lkml.org 
[lkml]   [2004]   [Nov]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    Date
    From
    Subject2.6.9 broke Cirque HID Touchpad support
    I just noticed that 2.6.9 seems to have broken support for my Cirque USB touchpad.
    With 2.6.8-gentoo-r4 it works fine with essentially the same kernel config:

    hub 2-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
    hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
    usb 2-1: new low speed USB device using address 3
    usb 2-1: skipped 1 descriptor after interface
    usb 2-1: new device strings: Mfr=1, Product=2, SerialNumber=0
    usb 2-1: default language 0x0409
    usb 2-1: Product: USB GlidePoint
    usb 2-1: Manufacturer: Cirque Corporation
    usb 2-1: hotplug
    usb 2-1: adding 2-1:1.0 (config #1, interface 0)
    usb 2-1:1.0: hotplug
    usbhid 2-1:1.0: usb_probe_interface
    usbhid 2-1:1.0: usb_probe_interface - got id
    input: USB HID v1.00 Mouse [Cirque Corporation USB GlidePoint] on usb-0000:00:10.0-1

    With 2.6.9-gentoo-r1 I get the following USB debug messages:

    usb 2-1: new low speed USB device using address 5
    uhci_hcd 0000:00:10.0: uhci_result_control: failed with status 440000
    [000001003f891300] link (3f891242) element (3f890060)
    0: [000001003f890060] link (3f8900c0) e0 LS Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=0, PID=2d(SETUP) (buf=3f5d84e0)
    1: [000001003f8900c0] link (00000001) e3 LS IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=0, PID=69(IN) (buf=00000000)
    uhci_hcd 0000:00:10.0: uhci_result_control: failed with status 440000
    [000001003f891300] link (3f891242) element (3f890060)
    0: [000001003f890060] link (3f8900c0) e0 LS Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=0, PID=2d(SETUP) (buf=3f5d84e0)
    1: [000001003f8900c0] link (00000001) e3 LS IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=0, PID=69(IN) (buf=00000000)
    usb 2-1: device not accepting address 5, error -71
    uhci_hcd 0000:00:10.0: CTRL: TypeReq=0x2301 val=0x2 idx=0x0 len=0 ==> -32
    usb 2-1: new low speed USB device using address 6
    uhci_hcd 0000:00:10.0: uhci_result_control: failed with status 440000
    [000001003f891300] link (3f891242) element (3f890060)
    0: [000001003f890060] link (3f8900c0) e0 LS Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=0, PID=2d(SETUP) (buf=3f5d84e0)
    1: [000001003f8900c0] link (00000001) e3 LS IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=0, PID=69(IN) (buf=00000000)
    uhci_hcd 0000:00:10.0: uhci_result_control: failed with status 440000
    [000001003f891300] link (3f891242) element (3f890060)
    0: [000001003f890060] link (3f8900c0) e0 LS Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=0, PID=2d(SETUP) (buf=3f5d8500)
    1: [000001003f8900c0] link (00000001) e3 LS IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=0, PID=69(IN) (buf=00000000)
    usb 2-1: device not accepting address 6, error -71

    Here are relevant config vars:
    CONFIG_X86_64=y
    CONFIG_64BIT=y
    CONFIG_X86=y
    CONFIG_MMU=y
    CONFIG_RWSEM_GENERIC_SPINLOCK=y
    CONFIG_X86_TSC=y
    CONFIG_X86_GOOD_APIC=y
    CONFIG_X86_IO_APIC=y
    CONFIG_X86_LOCAL_APIC=y
    CONFIG_MTRR=y
    CONFIG_SMP=y
    CONFIG_PREEMPT=y

    CONFIG_INPUT=y

    CONFIG_INPUT_EVDEV=y
    CONFIG_INPUT_MOUSE=y

    #
    # Userland interfaces
    #
    CONFIG_INPUT_MOUSEDEV=y
    CONFIG_INPUT_MOUSEDEV_PSAUX=y
    CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
    CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
    CONFIG_INPUT_JOYDEV=y


    CONFIG_USB=y
    CONFIG_USB_DEBUG=y

    #
    # Miscellaneous USB options
    #
    CONFIG_USB_DEVICEFS=y
    # CONFIG_USB_BANDWIDTH is not set
    # CONFIG_USB_DYNAMIC_MINORS is not set
    # CONFIG_USB_SUSPEND is not set
    # CONFIG_USB_OTG is not set

    #
    # USB Host Controller Drivers
    #
    CONFIG_USB_EHCI_HCD=y
    CONFIG_USB_UHCI_HCD=y

    CONFIG_USB_HID=y
    CONFIG_USB_HIDINPUT=y
    # CONFIG_HID_FF is not set
    CONFIG_USB_HIDDEV=y

    --
    James Lamanna
    -
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

    \
     
     \ /
      Last update: 2005-03-22 14:07    [W:0.024 / U:165.440 seconds]
    ©2003-2017 Jasper Spaans. hosted at Digital OceanAdvertise on this site