lkml.org 
[lkml]   [2004]   [Oct]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    Date
    From
    SubjectRe: sata_sil command 0x25 timeout, stat 0x50 host_stat 0x64
    An update. I read that 2.6.7 might work better for the sata_sil driver, so
    i tried running this version. But 2.6.7 doesn't solve my problem:

    sata_sil version 0.54
    PCI: Found IRQ 9 for device 0000:00:0e.0
    ata1: SATA max UDMA/100 cmd 0xD086AE80 ctl 0xD086AE8A bmdma 0xD086AE00 irq
    9
    ata2: SATA max UDMA/100 cmd 0xD086AEC0 ctl 0xD086AECA bmdma 0xD086AE08 irq
    9
    ata1: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4003 85:7c69 86:3e01 87:4003
    88:207f
    ata1: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
    irq 9: nobody cared!
    [<c01057fa>] __report_bad_irq+0x2a/0x90
    [<c01058f0>] note_interrupt+0x70/0xb0
    [<c0105b00>] do_IRQ+0xe0/0xf0
    [<c0103fac>] common_interrupt+0x18/0x20
    [<c01161ae>] __do_softirq+0x2e/0x80
    [<c0116227>] do_softirq+0x27/0x30
    [<c0105ae5>] do_IRQ+0xc5/0xf0
    [<c0103fac>] common_interrupt+0x18/0x20
    [<c01c007b>] idr_pre_get+0x2b/0x50
    [<c010d5c4>] delay_tsc+0x14/0x20
    [<c01c3ff2>] __delay+0x12/0x20
    [<c023252d>] ata_busy_sleep+0x1d/0x130
    [<c0232e44>] ata_dev_set_xfermode+0x94/0x190
    [<c0232f94>] ata_dev_set_udma+0x54/0xc0
    [<c02324d1>] ata_set_mode+0x51/0x90
    [<c02322d8>] ata_port_reset+0x88/0xc0
    [<c0234500>] ata_probe_task+0x0/0x60
    [<c02342a8>] ata_thread_iter+0x48/0xc0
    [<c0234513>] ata_probe_task+0x13/0x60
    [<c011ffdd>] worker_thread+0x1ad/0x250
    [<c010ff10>] default_wake_function+0x0/0x20
    [<c010ff10>] default_wake_function+0x0/0x20
    [<c011fe30>] worker_thread+0x0/0x250
    [<c01231aa>] kthread+0xaa/0xb0
    [<c0123100>] kthread+0x0/0xb0
    [<c010223d>] kernel_thread_helper+0x5/0x18

    handlers:
    [<c0234120>] (ata_interrupt+0x0/0x140)
    Disabling IRQ #9
    ata1: dev 0 configured for UDMA/100
    scsi0 : sata_sil
    ata2: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4003 85:7c69 86:3e01 87:4003
    88:207f
    ata2: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
    ata2: dev 0 configured for UDMA/100
    scsi1 : sata_sil
    Vendor: ATA Model: Maxtor 6Y200M0 Rev: YAR5
    Type: Direct-Access ANSI SCSI revision: 05
    SCSI device sda: 398297088 512-byte hdwr sectors (203928 MB)
    SCSI device sda: drive cache: write back
    sda:<3>ata1: DMA timeout, stat 0x64
    unknown partition table
    Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
    Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
    Vendor: ATA Model: Maxtor 6Y200M0 Rev: YAR5
    Type: Direct-Access ANSI SCSI revision: 05
    SCSI device sdb: 398297088 512-byte hdwr sectors (203928 MB)
    SCSI device sdb: drive cache: write back
    sdb:<3>ata2: DMA timeout, stat 0x64
    unknown partition table
    Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
    Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 0
    PCI: Found IRQ 10 for device 0000:00:10.0
    ata3: SATA max UDMA/100 cmd 0xD0877C80 ctl 0xD0877C8A bmdma 0xD0877C00 irq
    10
    ata4: SATA max UDMA/100 cmd 0xD0877CC0 ctl 0xD0877CCA bmdma 0xD0877C08 irq
    10
    irq 10: nobody cared!
    [<c01057fa>] __report_bad_irq+0x2a/0x90
    [<c01058f0>] note_interrupt+0x70/0xb0
    [<c0105b00>] do_IRQ+0xe0/0xf0
    [<c0103fac>] common_interrupt+0x18/0x20
    [<c01161ae>] __do_softirq+0x2e/0x80
    [<c0116227>] do_softirq+0x27/0x30
    [<c0105ae5>] do_IRQ+0xc5/0xf0
    [<c0103fac>] common_interrupt+0x18/0x20
    [<c01c007b>] idr_pre_get+0x2b/0x50
    [<c010d5c4>] delay_tsc+0x14/0x20
    [<c01c3ff2>] __delay+0x12/0x20
    [<c023252d>] ata_busy_sleep+0x1d/0x130
    [<c0231d3b>] ata_dev_identify+0xdb/0x5f0
    [<c01c3ff2>] __delay+0x12/0x20
    [<c02329b9>] ata_bus_reset+0x129/0x210
    [<c02323e5>] sata_phy_reset+0xc5/0x140
    [<c0232284>] ata_port_reset+0x34/0xc0
    [<c0234500>] ata_probe_task+0x0/0x60
    [<c02342a8>] ata_thread_iter+0x48/0xc0
    [<c0234513>] ata_probe_task+0x13/0x60
    [<c011ffdd>] worker_thread+0x1ad/0x250
    [<c010ff10>] default_wake_function+0x0/0x20
    [<c010ff10>] default_wake_function+0x0/0x20
    [<c011fe30>] worker_thread+0x0/0x250
    [<c01231aa>] kthread+0xaa/0xb0
    [<c0123100>] kthread+0x0/0xb0
    [<c010223d>] kernel_thread_helper+0x5/0x18

    handlers:
    [<c0234120>] (ata_interrupt+0x0/0x140)
    Disabling IRQ #10
    ata3: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4003 85:7c69 86:3e01 87:4003
    88:207f
    ata3: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
    ata3: dev 0 configured for UDMA/100
    scsi2 : sata_sil
    ata4: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4003 85:7c69 86:3e01 87:4003
    88:207f
    ata4: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
    ata4: dev 0 configured for UDMA/100
    scsi3 : sata_sil
    Vendor: ATA Model: Maxtor 6Y200M0 Rev: YAR5
    Type: Direct-Access ANSI SCSI revision: 05
    SCSI device sdc: 398297088 512-byte hdwr sectors (203928 MB)
    SCSI device sdc: drive cache: write back
    sdc:<3>ata3: DMA timeout, stat 0x64
    unknown partition table
    Attached scsi disk sdc at scsi2, channel 0, id 0, lun 0
    Attached scsi generic sg2 at scsi2, channel 0, id 0, lun 0, type 0
    Vendor: ATA Model: Maxtor 6Y200M0 Rev: YAR5
    Type: Direct-Access ANSI SCSI revision: 05
    SCSI device sdd: 398297088 512-byte hdwr sectors (203928 MB)
    SCSI device sdd: drive cache: write back
    sdd:<3>ata4: DMA timeout, stat 0x64
    unknown partition table
    Attached scsi disk sdd at scsi3, channel 0, id 0, lun 0
    Attached scsi generic sg3 at scsi3, channel 0, id 0, lun 0, type 0


    I will try further to get it working :)

    Greetings,
    Johannes Peeters

    On Sat, 9 Oct 2004, Johannes Peeters wrote:

    > Hello,
    >
    > I tried a lot of settings to get my sata drives working. I'm using 2 Sata
    > Sil3112 controllers (SATALink, Sil3112ACT144, Q22389.110A & Q22389.119A)
    > with both the latest bios (4.2.50) and 4 Maxtor Diamond Max Plug 9
    > (6Y200M0) harddisk.
    >
    > In kernel 2.6.8.1, the siimage driver is working fine. The sata_sil driver
    > howevers gives me weird timeouts:
    >
    > libata version 1.02 loaded.
    > sata_sil version 0.54
    > PCI: Found IRQ 9 for device 0000:00:0e.0
    > ata1: SATA max UDMA/100 cmd 0xD0854E80 ctl 0xD0854E8A bmdma 0xD0854E00 irq
    > 9
    > ata2: SATA max UDMA/100 cmd 0xD0854EC0 ctl 0xD0854ECA bmdma 0xD0854E08 irq
    > 9
    > irq 9: nobody cared!
    > [<c01062ba>] __report_bad_irq+0x2a/0x90
    > [<c01063b0>] note_interrupt+0x70/0xb0
    > [<c01065f0>] do_IRQ+0xe0/0xf0
    > [<c010497c>] common_interrupt+0x18/0x20
    > [<c0118fbe>] __do_softirq+0x2e/0x80
    > [<c0119037>] do_softirq+0x27/0x30
    > [<c01065d5>] do_IRQ+0xc5/0xf0
    > [<c010497c>] common_interrupt+0x18/0x20
    > [<c021007b>] des_small_fips_encrypt+0x41b/0x9f0
    > [<c010e496>] delay_tsc+0x16/0x20
    > [<c0216822>] __delay+0x12/0x20
    > [<d08623bd>] ata_busy_sleep+0x1d/0x130 [libata]
    > [<d0861bbb>] ata_dev_identify+0xdb/0x610 [libata]
    > [<c0216822>] __delay+0x12/0x20
    > [<d0862852>] ata_bus_reset+0x132/0x220 [libata]
    > [<d0862275>] sata_phy_reset+0xc5/0x140 [libata]
    > [<d0862124>] ata_bus_probe+0x34/0xb0 [libata]
    > [<d086462c>] ata_device_add+0x1ac/0x250 [libata]
    > [<d0863ec0>] ata_interrupt+0x0/0x1b0 [libata]
    > [<d0858511>] sil_init_one+0x281/0x320 [sata_sil]
    > [<c0221702>] pci_device_probe_static+0x52/0x70
    > [<c022175c>] __pci_device_probe+0x3c/0x50
    > [<c022179c>] pci_device_probe+0x2c/0x50
    > [<c0261caf>] bus_match+0x3f/0x70
    > [<c0261ddc>] driver_attach+0x5c/0xa0
    > [<c0262301>] bus_add_driver+0x91/0xb0
    > [<c02628af>] driver_register+0x2f/0x40
    > [<c0221a1c>] pci_register_driver+0x5c/0x90
    > [<d085b00f>] sil_init+0xf/0x1b [sata_sil]
    > [<c012a5c8>] sys_init_module+0x108/0x1d0
    > [<c010400f>] syscall_call+0x7/0xb
    > handlers:
    > [<d0863ec0>] (ata_interrupt+0x0/0x1b0 [libata])
    > Disabling IRQ #9
    > ata1: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4003 85:7c69 86:3e01 87:4003
    > 88:207f
    > ata1: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
    > ata1: dev 0 configured for UDMA/100
    > scsi0 : sata_sil
    > ata2: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4003 85:7c69 86:3e01 87:4003
    > 88:207f
    > ata2: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
    > ata2: dev 0 configured for UDMA/100
    > scsi1 : sata_sil
    > Vendor: ATA Model: Maxtor 6Y200M0 Rev: YAR5
    > Type: Direct-Access ANSI SCSI revision: 05
    > SCSI device sda: 398297088 512-byte hdwr sectors (203928 MB)
    > SCSI device sda: drive cache: write back
    > sda:<3>ata1: command 0x25 timeout, stat 0x50 host_stat 0x64
    > unknown partition table
    > Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
    > Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
    > Vendor: ATA Model: Maxtor 6Y200M0 Rev: YAR5
    > Type: Direct-Access ANSI SCSI revision: 05
    > SCSI device sdb: 398297088 512-byte hdwr sectors (203928 MB)
    > SCSI device sdb: drive cache: write back
    > sdb:<3>ata2: command 0x25 timeout, stat 0x50 host_stat 0x64
    > unknown partition table
    > Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
    > Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 0
    > PCI: Found IRQ 10 for device 0000:00:10.0
    > ata3: SATA max UDMA/100 cmd 0xD0856C80 ctl 0xD0856C8A bmdma 0xD0856C00 irq
    > 10
    > ata4: SATA max UDMA/100 cmd 0xD0856CC0 ctl 0xD0856CCA bmdma 0xD0856C08 irq
    > 10
    > irq 10: nobody cared!
    > [<c01062ba>] __report_bad_irq+0x2a/0x90
    > [<c01063b0>] note_interrupt+0x70/0xb0
    > [<c01065f0>] do_IRQ+0xe0/0xf0
    > [<c010497c>] common_interrupt+0x18/0x20
    > [<c0118fbe>] __do_softirq+0x2e/0x80
    > [<c0119037>] do_softirq+0x27/0x30
    > [<c01065d5>] do_IRQ+0xc5/0xf0
    > [<c010497c>] common_interrupt+0x18/0x20
    > [<c021007b>] des_small_fips_encrypt+0x41b/0x9f0
    > [<c010e494>] delay_tsc+0x14/0x20
    > [<c0216822>] __delay+0x12/0x20
    > [<d08623bd>] ata_busy_sleep+0x1d/0x130 [libata]
    > [<d0861bbb>] ata_dev_identify+0xdb/0x610 [libata]
    > [<c0216822>] __delay+0x12/0x20
    > [<d0862852>] ata_bus_reset+0x132/0x220 [libata]
    > [<d0862275>] sata_phy_reset+0xc5/0x140 [libata]
    > [<d0862124>] ata_bus_probe+0x34/0xb0 [libata]
    > [<d086462c>] ata_device_add+0x1ac/0x250 [libata]
    > [<d0863ec0>] ata_interrupt+0x0/0x1b0 [libata]
    > [<d0858511>] sil_init_one+0x281/0x320 [sata_sil]
    > [<c0221702>] pci_device_probe_static+0x52/0x70
    > [<c022175c>] __pci_device_probe+0x3c/0x50
    > [<c022179c>] pci_device_probe+0x2c/0x50
    > [<c0261caf>] bus_match+0x3f/0x70
    > [<c0261ddc>] driver_attach+0x5c/0xa0
    > [<c0262301>] bus_add_driver+0x91/0xb0
    > [<c02628af>] driver_register+0x2f/0x40
    > [<c0221a1c>] pci_register_driver+0x5c/0x90
    > [<d085b00f>] sil_init+0xf/0x1b [sata_sil]
    > [<c012a5c8>] sys_init_module+0x108/0x1d0
    > [<c010400f>] syscall_call+0x7/0xb
    > handlers:
    > [<d0863ec0>] (ata_interrupt+0x0/0x1b0 [libata])
    > Disabling IRQ #10
    > ata3: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4003 85:7c69 86:3e01 87:4003
    > 88:207f
    > ata3: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
    > ata3: dev 0 configured for UDMA/100
    > scsi2 : sata_sil
    > ata4: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4003 85:7c69 86:3e01 87:4003
    > 88:207f
    > ata4: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
    > ata4: dev 0 configured for UDMA/100
    > scsi3 : sata_sil
    > Vendor: ATA Model: Maxtor 6Y200M0 Rev: YAR5
    > Type: Direct-Access ANSI SCSI revision: 05
    > SCSI device sdc: 398297088 512-byte hdwr sectors (203928 MB)
    > SCSI device sdc: drive cache: write back
    > sdc:<3>ata3: command 0x25 timeout, stat 0x50 host_stat 0x64
    > unknown partition table
    > Attached scsi disk sdc at scsi2, channel 0, id 0, lun 0
    > Attached scsi generic sg2 at scsi2, channel 0, id 0, lun 0, type 0
    > Vendor: ATA Model: Maxtor 6Y200M0 Rev: YAR5
    > Type: Direct-Access ANSI SCSI revision: 05
    > SCSI device sdd: 398297088 512-byte hdwr sectors (203928 MB)
    > SCSI device sdd: drive cache: write back
    > sdd:<3>ata4: command 0x25 timeout, stat 0x50 host_stat 0x64
    > unknown partition table
    > Attached scsi disk sdd at scsi3, channel 0, id 0, lun 0
    > Attached scsi generic sg3 at scsi3, channel 0, id 0, lun 0, type 0
    >
    > Reading/writing to this disc doesn't work, this gives me an endless
    > process.
    >
    >
    >
    > I also tried with 2.6.9-rc3-bk7, but that gives me an other problem:
    >
    >
    > libata version 1.02 loaded.
    > sata_sil version 0.54
    > PCI: Found IRQ 9 for device 0000:00:0e.0
    > ata1: SATA max UDMA/100 cmd 0xD0854E80 ctl 0xD0854E8A bmdma 0xD0854E00 irq
    > 9
    > ata2: SATA max UDMA/100 cmd 0xD0854EC0 ctl 0xD0854ECA bmdma 0xD0854E08 irq
    > 9
    > ata1: no device found (phy stat 00000000)
    > scsi0 : sata_sil
    > irq 9: nobody cared!
    > [<c0105e9a>] __report_bad_irq+0x2a/0x90
    > [<c0105f90>] note_interrupt+0x70/0xb0
    > [<c01061a0>] do_IRQ+0xe0/0xf0
    > [<c010413c>] common_interrupt+0x18/0x20
    > [<c011801e>] __do_softirq+0x2e/0x90
    > [<c01180a7>] do_softirq+0x27/0x30
    > [<c0106185>] do_IRQ+0xc5/0xf0
    > [<c010413c>] common_interrupt+0x18/0x20
    > [<c01020c3>] default_idle+0x23/0x40
    > [<c0102154>] cpu_idle+0x34/0x40
    > [<c044272b>] start_kernel+0x13b/0x160
    > [<c0442370>] unknown_bootoption+0x0/0x160
    > handlers:
    > [<d0865160>] (ata_interrupt+0x0/0x1c0 [libata])
    > Disabling IRQ #9
    > ata2: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4003 85:7c69 86:3e01 87:4003
    > 88:207f
    > ata2: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
    >
    > After this, loading the module stops. I've wait a couple of hours, but
    > this was the last message.
    > Trying to enable/disable APIC & IOAPIC didn't solve the problem.
    >
    > Any suggestions?
    >
    > Thanks,
    > Johannes Peeters
    > -
    > To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    > the body of a message to majordomo@vger.kernel.org
    > More majordomo info at http://vger.kernel.org/majordomo-info.html
    > Please read the FAQ at http://www.tux.org/lkml/
    >
    -
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

    \
     
     \ /
      Last update: 2005-03-22 14:06    [W:0.054 / U:1.464 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site