Messages in this thread | | | From | tomepperly@comcast ... | Subject | CPU lockup during halt for Shuttle SB61G2 p4 with hyperthreading 2.4.24 | Date | Thu, 29 Jan 2004 18:11:24 +0000 |
| |
[1.] CPU lockup during halt for Shuttle SB61G2 p4 with hyperthreading
[2.] Full description I've got a Shuttle SB61G2 purchased 12/31/03 with a 2.6GHz P4 with hyperthreading. Sometimes when shutting down, I get the "Power down." message, but it doesn't actually power down the system. It just sits there indefinitely. I tried enabling nmi_watchdog=1, and I intermittently get kernel oopses. I only started having problems when I compiled the kernel with SMP enabled. A non-SMP kernel never locks up.
I transcribed the oops message from my screen and ran ksymoops on it. I am running a vanilla 2.4.24 downloaded from kernel.org compiled with gcc-2.95.
Please Cc me on replies as I am not subscribed to linux-kernel.
[3.] Keywords: Lockup SMP [4.] Linux version 2.4.24-vanilla (root@faerun) (gcc version 2.95.4 20011002 (Debian prerelease)) #3 SMP Fri Jan 16 07:30:34 PST 2004 [5.] I had to write this on paper and then type it in by hand. I was very careful, but transcription errors are always a possibility: ksymoops 2.4.9 on i686 2.4.24-vanilla. Options used -V (default) -k /proc/ksyms (default) -l /proc/modules (default) -o /lib/modules/2.4.24-vanilla/ (default) -m /boot/System.map-2.4.24-vanilla (default)
Warning: You did not tell me where to find symbol information. I will assume that the log matches the kernel and modules that are running right now and I'll use the default options above for symbol resolution. If the current kernel and/or modules do not match the log, you can get more accurate output by telling me the kernel version and where to find map, modules, ksyms etc. ksymoops -h explains the options.
Error (regular_file): read_system_map stat /boot/System.map-2.4.24-vanilla failed ksymoops: No such file or directory Warning (compare_maps): mismatch on symbol _nv000173rm , nvidia says f8e4bb20, /lib/modules/2.4.24-vanilla/kernel/drivers/video/nvidia.o says f8e4b900. Ignoring /lib/modules/2.4.24-vanilla/kernel/drivers/video/nvidia.o entry NMI Watchdog detected LOCKUP on CPU1, eip c01a6757, registers: EIP: 0010: [<c01a6757>] Tainted: P Using defaults from ksymoops -t elf32-i386 -a i386 EFLAGS: 00000046 eax: 00000011 ebx: f7cc9e48 ecx: f7cc9e48 edx: 00000400 esi: 00000010 edi: 00000000 ebp: bffffbc8 esp: f7cc9e08 ds: 0018 es: 0018 ss: 0018 Process halt (pid: 1220, stackpage=f7cc9000) Stack: 00000018 c01b29cb 00000400 f7cc9e48 00000010 00002001 c02e5e18 00000011 c02e5e18 c01b26d7 00000010 f7cc9e48 c1c32114 00002001 00000000 00000000 00000000 c01b24b9 00000000 00000001 f7cc9e68 00002001 c02e5e40 c02e5e40 Call Trace: [<c01b29cb>] [<c01b26d7>] [<c01b24b9>] [<c01b2d5e>] [<c01c1394>] [<c0105523>] [<c012487d>] [<c0122d8a>] [<c0122e11>] [<c01231067>] [<c01239a5>] [<c0141864>] [<c014954d>] [<c0106f27>] Code: 66 89 01 eb 11 eb 11 8d 74 26 00 ed 89 01 eb 08 0f 0b 4f 01 ec ff
>>EIP; c01a6757 <acpi_os_stall_R__ver_acpi_os_stall+67/17c> <=====
>>ebx; f7cc9e48 <_end+3794bfe4/385cf1fc> >>ecx; f7cc9e48 <_end+3794bfe4/385cf1fc> >>esp; f7cc9e08 <_end+3794bfa4/385cf1fc>
Trace; c01b29cb <acpi_set_register_R__ver_acpi_set_register+4db/6cc> Trace; c01b26d7 <acpi_set_register_R__ver_acpi_set_register+1e7/6cc> Trace; c01b24b9 <acpi_get_register_R__ver_acpi_get_register+51/88> Trace; c01b2d5e <acpi_enter_sleep_state_R__ver_acpi_enter_sleep_state+1a2/1bc> Trace; c01c1394 <acpi_pci_irq_enable_R__ver_acpi_pci_irq_enable+bb4/2868> Trace; c0105523 <machine_power_off+b/314> Trace; c012487d <unregister_reboot_notifier+365/11a4> Trace; c0122d8a <dequeue_signal+432/438> Trace; c0122e11 <send_sig_info+81/98> Trace; c01231067 <END_OF_CODE+b083c2710/????> Trace; c01239a5 <notify_parent+685/edc> Trace; c0141864 <blkdev_put+148/154> Trace; c014954d <kill_fasync+4f5/528> Trace; c0106f27 <__read_lock_failed+115f/1520>
Code; c01a6757 <acpi_os_stall_R__ver_acpi_os_stall+67/17c> 00000000 <_EIP>: Code; c01a6757 <acpi_os_stall_R__ver_acpi_os_stall+67/17c> <===== 0: 66 89 01 mov %ax,(%ecx) <===== Code; c01a675a <acpi_os_stall_R__ver_acpi_os_stall+6a/17c> 3: eb 11 jmp 16 <_EIP+0x16> Code; c01a675c <acpi_os_stall_R__ver_acpi_os_stall+6c/17c> 5: eb 11 jmp 18 <_EIP+0x18> Code; c01a675e <acpi_os_stall_R__ver_acpi_os_stall+6e/17c> 7: 8d 74 26 00 lea 0x0(%esi,1),%esi Code; c01a6762 <acpi_os_stall_R__ver_acpi_os_stall+72/17c> b: ed in (%dx),%eax Code; c01a6763 <acpi_os_stall_R__ver_acpi_os_stall+73/17c> c: 89 01 mov %eax,(%ecx) Code; c01a6765 <acpi_os_stall_R__ver_acpi_os_stall+75/17c> e: eb 08 jmp 18 <_EIP+0x18> Code; c01a6767 <acpi_os_stall_R__ver_acpi_os_stall+77/17c> 10: 0f 0b ud2a Code; c01a6769 <acpi_os_stall_R__ver_acpi_os_stall+79/17c> 12: 4f dec %edi Code; c01a676a <acpi_os_stall_R__ver_acpi_os_stall+7a/17c> 13: 01 ec add %ebp,%esp Code; c01a676c <acpi_os_stall_R__ver_acpi_os_stall+7c/17c> 15: ff 00 incl (%eax)
2 warnings and 1 error issued. Results may not be reliable.
[6.] I booted my machine. gdm (X11) fires up using nVidia drivers. Choose shutdown from gdm menu. Oops. It happens every once in a while when I shutdown. [7.] [7.1] faerun:/usr/src/linux-2.4.24# sh scripts/ver_linux If some fields are empty or look unusual you may have an old version. Compare to the current minimal requirements in Documentation/Changes. Linux faerun 2.4.24-vanilla #3 SMP Fri Jan 16 07:30:34 PST 2004 i686 GNU/Linux Gnu C 3.3.3 Gnu make 3.80 util-linux 2.12 mount 2.12 modutils 2.4.26 e2fsprogs 1.35-WIP PPP 2.4.2 Linux C Library 2.3.2 Dynamic linker (ldd) 2.3.2 Procps 3.1.15 Net-tools 1.60 Console-tools 0.2.3 Sh-utils 5.0.91 Modules Loaded nvidia joydev mousedev hid input binfmt_misc uhci ide-scsi scsi_mod it87 i2c-proc i2c-isa i2c-core v_midi sound i810_audio ehci-hcd
I used "make CC=gcc-2.95 HOSTCC=gcc-2.95" when compiling the kernel and its modules.
faerun:/usr/src/linux-2.4.24# [7.2.] faerun:/usr/src/linux-2.4.24# cat /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 15 model : 2 model name : Intel(R) Pentium(R) 4 CPU 2.60GHz stepping : 9 cpu MHz : 2605.987 cache size : 512 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe cid bogomips : 5203.55 processor : 1 vendor_id : GenuineIntel cpu family : 15 model : 2 model name : Intel(R) Pentium(R) 4 CPU 2.60GHz stepping : 9 cpu MHz : 2605.987 cache size : 512 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe cid bogomips : 5203.55
Intel 865G chipset faerun:/usr/src/linux-2.4.24# [7.3.] faerun:/usr/src/linux-2.4.24# cat /proc/modules nvidia 1969376 14 (autoclean) joydev 7104 0 (unused) mousedev 3864 1 hid 13864 0 (unused) input 3456 0 [joydev mousedev hid] binfmt_misc 5896 1 uhci 24752 0 (unused) ide-scsi 8976 0 scsi_mod 87496 1 [ide-scsi] it87 9768 0 (unused) i2c-proc 5972 0 [it87] i2c-isa 788 0 (unused) i2c-core 14788 0 [it87 i2c-proc i2c-isa] v_midi 4996 0 (unused) sound 56428 0 [v_midi] i810_audio 24312 1 ehci-hcd 15880 0 (unused) faerun:/usr/src/linux-2.4.24# [7.4.] faerun:/usr/src/linux-2.4.24# cat /proc/ioports 0000-001f : dma1 0020-003f : pic1 0040-005f : timer 0060-006f : keyboard 0070-007f : rtc 0080-008f : dma page reg 00a0-00bf : pic2 00c0-00df : dma2 00f0-00ff : fpu 0170-0177 : ide1 01f0-01f7 : ide0 0290-0297 : it87 0376-0376 : ide1 03c0-03df : vga+ 03f6-03f6 : ide0 03f8-03ff : serial(set) 0500-051f : Intel Corp. 82801EB SMBus Controller 0cf8-0cff : PCI conf1 9000-90ff : Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ 9000-90ff : 8139too 9400-947f : VIA Technologies, Inc. IEEE 1394 Host Controller a000-a01f : Intel Corp. 82801EB USB a000-a01f : usb-uhci a400-a41f : Intel Corp. 82801EB USB a400-a41f : usb-uhci a800-a81f : Intel Corp. 82801EB USB a800-a81f : usb-uhci ac00-ac1f : Intel Corp. 82801EB USB ac00-ac1f : usb-uhci b400-b4ff : Intel Corp. 82801EB AC'97 Audio Controller b400-b4ff : Intel ICH5 b800-b83f : Intel Corp. 82801EB AC'97 Audio Controller b800-b83f : Intel ICH5 f000-f00f : Intel Corp. 82801EB Ultra ATA Storage Controller f000-f007 : ide0 f008-f00f : ide1 faerun:/usr/src/linux-2.4.24# cat /proc/iomem 00000000-0009f7ff : System RAM 0009f800-0009ffff : reserved 000a0000-000bffff : Video RAM area 000c0000-000c7fff : Video ROM 000f0000-000fffff : System ROM 00100000-3ffeffff : System RAM 00100000-00281001 : Kernel code 00281002-0031e83f : Kernel data 3fff0000-3fff2fff : ACPI Non-volatile Storage 3fff3000-3fffffff : ACPI Tables 40000000-400003ff : Intel Corp. 82801EB Ultra ATA Storage Controller e8000000-efffffff : PCI Bus #01 e8000000-efffffff : PCI device 10de:0322 (nVidia Corporation) f0000000-f3ffffff : Intel Corp. 82865G/PE/P Processor to I/O Controller f4000000-f5ffffff : PCI Bus #01 f4000000-f4ffffff : PCI device 10de:0322 (nVidia Corporation) f7000000-f70000ff : Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ f7000000-f70000ff : 8139too f7001000-f70017ff : VIA Technologies, Inc. IEEE 1394 Host Controller f8000000-f80003ff : Intel Corp. 82801EB USB2 f8000000-f80003ff : ehci_hcd f8001000-f80011ff : Intel Corp. 82801EB AC'97 Audio Controller f8001000-f80011ff : ich_audio MMBAR f8002000-f80020ff : Intel Corp. 82801EB AC'97 Audio Controller f8002000-f80020ff : ich_audio MBBAR fec00000-ffffffff : reserved faerun:/usr/src/linux-2.4.24# [7.5.] faerun:/usr/src/linux-2.4.24# lspci -vvv 00:00.0 Host bridge: Intel Corp. 82865G/PE/P Processor to I/O Controller (rev 02) Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer: Unknown device fb61 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 0 Region 0: Memory at f0000000 (32-bit, prefetchable) [size=64M] Capabilities: [e4] #09 [0106] Capabilities: [a0] AGP version 3.0 Status: RQ=32 Iso- ArqSz=2 Cal=2 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8 Command: RQ=1 ArqSz=0 Cal=2 SBA+ AGP+ GART64- 64bit- FW- Rate=x8 00:01.0 PCI bridge: Intel Corp. 82865G/PE/P Processor to AGP Controller (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 0000f000-00000fff Memory behind bridge: f4000000-f5ffffff Prefetchable memory behind bridge: e8000000-efffffff BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B- 00:1d.0 USB Controller: Intel Corp. 82801EB USB (rev 02) (prog-if 00 [UHCI]) Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer: Unknown device fb61 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 4: I/O ports at ac00 [size=32] 00:1d.1 USB Controller: Intel Corp. 82801EB USB (rev 02) (prog-if 00 [UHCI]) Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer: Unknown device fb61 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 4: I/O ports at a000 [size=32] 00:1d.2 USB Controller: Intel Corp. 82801EB USB (rev 02) (prog-if 00 [UHCI]) Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer: Unknown device fb61 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 4: I/O ports at a400 [size=32] 00:1d.3 USB Controller: Intel Corp. 82801EB USB (rev 02) (prog-if 00 [UHCI]) Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer: Unknown device fb61 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 4: I/O ports at a800 [size=32] 00:1d.7 USB Controller: Intel Corp. 82801EB USB2 (rev 02) (prog-if 20 [EHCI]) Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer: Unknown device fb61 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin D routed to IRQ 23 Region 0: Memory at f8000000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:1e.0 PCI bridge: Intel Corp. 82801BA/CA/DB/EB PCI Bridge (rev c2) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=32 I/O behind bridge: 00009000-00009fff Memory behind bridge: f6000000-f7ffffff Prefetchable memory behind bridge: fff00000-000fffff BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- 00:1f.0 ISA bridge: Intel Corp. 82801EB LPC Interface Controller (rev 02) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 00:1f.1 IDE interface: Intel Corp. 82801EB Ultra ATA Storage Controller (rev 02) (prog-if 8a [Master SecP PriP]) Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer: Unknown device fb61 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at <unassigned> Region 1: I/O ports at <unassigned> Region 2: I/O ports at <unassigned> Region 3: I/O ports at <unassigned> Region 4: I/O ports at f000 [size=16] Region 5: Memory at 40000000 (32-bit, non-prefetchable) [size=1K] 00:1f.3 SMBus: Intel Corp. 82801EB SMBus Controller (rev 02) Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer: Unknown device fb61 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin B routed to IRQ 17 Region 4: I/O ports at 0500 [size=32] 00:1f.5 Multimedia audio controller: Intel Corp. 82801EB AC'97 Audio Controller (rev 02) Subsystem: Holco Enterprise Co, Ltd/Shuttle Computer: Unknown device c09d Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin B routed to IRQ 17 Region 0: I/O ports at b400 [size=256] Region 1: I/O ports at b800 [size=64] Region 2: Memory at f8001000 (32-bit, non-prefetchable) [size=512] Region 3: Memory at f8002000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 01:00.0 VGA compatible controller: nVidia Corporation NV34 [GeForce FX 5200] (rev a1) (prog-if 00 [VGA]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 248 (1250ns min, 250ns max) Interrupt: pin A routed to IRQ 16 Region 0: Memory at f4000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at e8000000 (32-bit, prefetchable) [size=128M] Expansion ROM at <unassigned> [disabled] [size=128K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [44] AGP version 3.0 Status: RQ=32 Iso- ArqSz=0 Cal=3 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8 Command: RQ=32 ArqSz=2 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x8 02:06.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RT8139 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (8000ns min, 16000ns max) Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at 9000 [size=256] Region 1: Memory at f7000000 (32-bit, non-prefetchable) [size=256] Expansion ROM at <unassigned> [disabled] [size=64K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 02:08.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 80) (prog-if 10 [OHCI]) Subsystem: VIA Technologies, Inc. IEEE 1394 Host Controller Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (8000ns max), Cache Line Size: 0x08 (32 bytes) Interrupt: pin A routed to IRQ 20 Region 0: Memory at f7001000 (32-bit, non-prefetchable) [size=2K] Region 1: I/O ports at 9400 [size=128] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- faerun:/usr/src/linux-2.4.24# [7.6.] faerun:/usr/src/linux-2.4.24# cat /proc/scsi/scsi Attached devices: none [7.7.] faerun:/usr/src/linux-2.4.24# cat /proc/acpi/info version: 20031002 states: S0 S1 S4 S5 faerun:/usr/src/linux-2.4.24# cat /proc/acpi/alarm 2004-01-27 11:00:10 - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |