Messages in this thread | | | From | Arkadiusz Miskiewicz <> | Subject | Re: USB: irq 11: nobody cared! | 2.6.0test5 | Date | Tue, 9 Sep 2003 09:54:06 +0200 |
| |
On Monday 08 of September 2003 18:38, David Brownell wrote: > > 4) USB no longer working. Was working fine in vanilla test4.
Right now I'm testing on 2.6.0test5.
> Try changing uhci_reset() so it calls hc_reset() first,
OK, I'm recompiling it with such change:
static int uhci_reset(struct usb_hcd *hcd) { struct uhci_hcd *uhci = hcd_to_uhci(hcd);
uhci->io_addr = (unsigned long) hcd->regs;
+ reset_hc(uhci); /* Maybe kick BIOS off this hardware. Then reset, so we won't get * interrupts from any previous setup. */ pci_write_config_word(hcd->pdev, USBLEGSUP, USBLEGSUP_DEFAULT); - reset_hc(uhci); return 0; }
> There's the problem ... at least with your hardware and BIOS; > it worked OK on mine. It's VIA so strange things can happen (btw test3 was ok with usb).
Anyway when booting with acpi disabled I get USB mouse working!
Here is dmesg when acpi is enabled: Linux version 2.6.0 (builder@beton) (gcc version 3.3.1 (PLD Linux)) #1 Mon Sep 8 22:09:34 UTC 2003 Video mode to be used for restore is f07 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000cc000 - 00000000000d0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000000eff0000 (usable) BIOS-e820: 000000000eff0000 - 000000000eff8000 (ACPI data) BIOS-e820: 000000000eff8000 - 000000000f000000 (ACPI NVS) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) 0MB HIGHMEM available. 239MB LOWMEM available. On node 0 totalpages: 61424 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 57328 pages, LIFO batch:13 HighMem zone: 0 pages, LIFO batch:1 DMI 2.3 present. ACPI: RSDP (v000 AMI ) @ 0x000fa4a0 ACPI: RSDT (v001 AMIINT VIA_K7 0x00000010 MSFT 0x00000097) @ 0x0eff0000 ACPI: FADT (v001 AMIINT VIA_K7 0x00000011 MSFT 0x00000097) @ 0x0eff0030 ACPI: BOOT (v001 AMIINT VIA_K7 0x00000009 MSFT 0x00000097) @ 0x0eff00c0 ACPI: DSDT (v001 VIA TwisterK 0x00001000 INTL 0x02002024) @ 0x00000000 Building zonelist for node : 0 Kernel command line: BOOT_IMAGE=pld-2.6.0 ro root=303 console=ttyS0,57600n81 console=tty0 Initializing CPU#0 PID hash table entries: 1024 (order 10: 8192 bytes) Detected 1533.459 MHz processor. Console: colour VGA+ 80x60 Memory: 239664k/245696k available (1662k kernel code, 5336k reserved, 679k data, 164k init, 0k highmem) Calibrating delay loop... 3022.84 BogoMIPS Security Scaffold v1.0.0 initialized SELinux: Not enabled at boot. Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) -> /dev -> /dev/console -> /root CPU: After generic identify, caps: 0383f9ff c1cbf9ff 00000000 00000000 CPU: After vendor identify, caps: 0383f9ff c1cbf9ff 00000000 00000000 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) CPU: After all inits, caps: 0383f9ff c1cbf9ff 00000000 00000020 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: AMD mobile AMD Athlon(tm) XP-M 1800+ stepping 01 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xfdb51, last bus=1 PCI: Using configuration type 1 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20030813 ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: Power Resource [URP1] (off) ACPI: Power Resource [URP2] (off) ACPI: Power Resource [FDDP] (off) ACPI: Power Resource [LPTP] (off) ACPI: Embedded Controller [EC0] (gpe 5) ACPI: PCI Interrupt Link [LNKA] (IRQs 5 *9 10 11 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 5 9 10 11 14 15, disabled) ACPI: PCI Interrupt Link [LNKC] (IRQs 5 9 *10 11 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 5 9 *10 11 14 15) ACPI: Power Resource [FN10] (on) Linux Plug and Play Support v0.97 (c) Adam Belay PnPBIOS: Scanning system for PnP BIOS support... PnPBIOS: Found PnP BIOS installation structure at 0xc00f7710 PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x673b, dseg 0xf0000 PnPBIOS: Unknown tag '0x82', length '22'. PnPBIOS: 15 nodes reported by PnP BIOS; 15 recorded by driver ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5 ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11 ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11 ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 9 PCI: Using ACPI for IRQ routing PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off' pty: 256 Unix98 ptys configured SBF: Simple Boot Flag extension found and enabled. SBF: Setting boot flags 0x1 Machine check exception polling timer started. VFS: Disk quotas dquot_6.5.1 devfs: v1.22 (20021013) Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x0 Initializing Cryptographic API Applying VIA southbridge workaround. PCI: Via IRQ fixup for 0000:00:11.3, from 10 to 11 PCI: Via IRQ fixup for 0000:00:11.2, from 10 to 11 PCI: Via IRQ fixup for 0000:00:11.5, from 10 to 11 PCI: Via IRQ fixup for 0000:00:11.6, from 10 to 11 isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found w83877f_wdt: WDT driver for W83877F initialised. timeout=30 sec (nowayout=0) Serial: 8250/16550 driver $Revision: 1.90 $ IRQ sharing enabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller at PCI slot 0000:00:11.1 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: VIA vt8231 (rev 10) IDE UDMA100 controller on pci0000:00:11.1 ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio hda: TOSHIBA MK3021GAS, ATA DISK drive Using anticipatory scheduling io scheduler ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hdc: Samsung CD-RW/DVD-ROM SN-324B, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 128KiB hda: 58605120 sectors (30005 MB), CHS=58140/16/63, UDMA(100) /dev/ide/host0/bus0/target0/lun0: p1 p2 p3 mice: PS/2 mouse device common for all mice i8042.c: Detected active multiplexing controller, rev 1.0. serio: i8042 AUX0 port at 0x60,0x64 irq 12 serio: i8042 AUX1 port at 0x60,0x64 irq 12 serio: i8042 AUX2 port at 0x60,0x64 irq 12 serio: i8042 AUX3 port at 0x60,0x64 irq 12 input: AT Set 2 keyboard on isa0060/serio0 serio: i8042 KBD port at 0x60,0x64 irq 1 NET: Registered protocol family 2 IP: routing cache hash table of 2048 buckets, 16Kbytes TCP: Hash tables configured (established 16384 bind 32768) NET: Registered protocol family 1 NET: Registered protocol family 17 BIOS EDD facility v0.09 2003-Jan-22, 1 devices found ACPI: (supports S0 S3 S4 S5) RAMDISK: Compressed image found at block 0 Freeing initrd memory: 187k freed VFS: Mounted root (romfs filesystem) readonly. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Trying to move old root to /initrd ... failed Unmounting old root Trying to free ramdisk memory ... okay Freeing unused kernel memory: 164k freed Adding 265064k swap on /dev/hda2. Priority:-1 extents:1 blk: queue c1389800, I/O limit 4095Mb (mask 0xffffffff) EXT3 FS on hda3, internal journal drivers/usb/core/usb.c: registered new driver usbfs drivers/usb/core/usb.c: registered new driver hub end_request: I/O error, dev hdc, sector 0 hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.12 Capability LSM initialized ACPI: AC Adapter [AC0] (on-line) ACPI: Battery Slot [BAT0] (battery present) ACPI: Power Button (FF) [PWRF] ACPI: Lid Switch [LID] ACPI: Sleep Button (CM) [SLPB] ACPI: Fan [FAN1] (off) ACPI: Processor [CPU1] (supports C1 C2) ACPI: Thermal Zone [THRM] (58 C) powernow: AMD K7 CPU detected. powernow: PowerNOW! Technology present. Can scale: frequency and voltage. powernow: Found PSB header at c00faf80 powernow: Table version: 0x12 powernow: Flags: 0x0 (Mobile voltage regulator) powernow: Settling Time: 100 microseconds. powernow: Has 86 PST tables. (Only dumping ones relevant to this CPU). powernow: PST:74 (@c00fb590) powernow: cpuid: 0x781 fsb: 133 maxFID: 0x1 startvid: 0xb powernow: FID: 0x6 (6.0x [798MHz]) VID: 0xd (1.350V) powernow: FID: 0x7 (6.5x [864MHz]) VID: 0xd (1.350V) powernow: FID: 0x9 (7.5x [997MHz]) VID: 0xd (1.350V) powernow: FID: 0xb (8.5x [1130MHz]) VID: 0xd (1.350V) powernow: FID: 0xd (9.5x [1263MHz]) VID: 0xd (1.350V) powernow: FID: 0xf (10.5x [1396MHz]) VID: 0xc (1.400V) powernow: FID: 0x1 (11.5x [1529MHz]) VID: 0xb (1.450V)
powernow: Minimum speed 798 MHz. Maximum speed 1529 MHz. input: PS/2 Generic Mouse on isa0060/serio2 drivers/usb/core/usb.c: registered new driver usbmouse drivers/usb/input/usbmouse.c: v1.6:USB HID Boot Protocol mouse driver drivers/usb/core/usb.c: registered new driver hiddev drivers/usb/core/usb.c: registered new driver hid drivers/usb/input/hid-core.c: v2.0:USB HID core driver PCI: Setting latency timer of device 0000:00:11.5 to 64 NTFS driver 2.1.4 [Flags: R/W MODULE]. NTFS volume version 3.1. Linux Kernel Card Services 3.1.22 options: [pci] [cardbus] [pm] Yenta: CardBus bridge found at 0000:00:08.0 [1584:3000] Yenta: ISA IRQ list 0400, PCI irq5 Socket status: 30000007 cs: IO port probe 0x0c00-0x0cff: clean. cs: IO port probe 0x0800-0x08ff: excluding 0x800-0x87f cs: IO port probe 0x0100-0x04ff: excluding 0x378-0x37f 0x3c0-0x3df 0x400-0x40f 0x4d0-0x4d7 cs: IO port probe 0x0a00-0x0aff: clean. ohci-hcd: 2003 Feb 24 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ohci-hcd: block sizes: ed 64 td 64 drivers/usb/host/uhci-hcd.c: USB Universal Host Controller Interface driver v2.1 uhci-hcd 0000:00:11.2: UHCI Host Controller irq 11: nobody cared! Call Trace: [<c010cbdb>] __report_bad_irq+0x2b/0x90 [<c010ccd4>] note_interrupt+0x64/0xa0 [<c010cf6e>] do_IRQ+0x12e/0x140 [<c010b49c>] common_interrupt+0x18/0x20 [<c0124603>] do_softirq+0x43/0xa0 [<c010cf48>] do_IRQ+0x108/0x140 [<c010b49c>] common_interrupt+0x18/0x20 [<c01addcc>] pci_bus_write_config_word+0x5c/0x80 [<cf9b94a0>] uhci_reset+0x40/0x50 [uhci_hcd] [<cf89ba32>] usb_hcd_pci_probe+0x192/0x480 [usbcore] [<c01b17ab>] pci_device_probe_static+0x4b/0x60 [<c01b1916>] __pci_device_probe+0x36/0x50 [<c01b195c>] pci_device_probe+0x2c/0x50 [<c01f5ded>] bus_match+0x3d/0x70 [<c01f5f40>] driver_attach+0x70/0xb0 [<c01f6241>] bus_add_driver+0xa1/0xc0 [<c01f6691>] driver_register+0x31/0x40 [<c01b1bde>] pci_register_driver+0x5e/0x90 [<cf8cb0c7>] uhci_hcd_init+0xc7/0x143 [uhci_hcd] [<c01370a3>] sys_init_module+0x123/0x270 [<c010b32f>] syscall_call+0x7/0xb
handlers: [<cf9234b0>] (snd_via82xx_interrupt+0x0/0x110 [snd_via82xx]) Disabling IRQ #11 uhci-hcd 0000:00:11.2: irq 11, io base 0000d400 uhci-hcd 0000:00:11.2: new USB bus registered, assigned bus number 1 hub 1-0:0: USB hub found hub 1-0:0: 2 ports detected uhci-hcd 0000:00:11.3: UHCI Host Controller uhci-hcd 0000:00:11.3: irq 11, io base 0000d800 uhci-hcd 0000:00:11.3: new USB bus registered, assigned bus number 2 hub 2-0:0: USB hub found hub 2-0:0: 2 ports detected hub 1-0:0: debounce: port 1: delay 100ms stable 4 status 0x301 hub 1-0:0: new USB device on port 1, assigned address 2 usb 1-1: control timeout on ep0out uhci-hcd 0000:00:11.2: Unlink after no-IRQ? Different ACPI or APIC settings may help. NET: Registered protocol family 10 Disabled Privacy Extensions on device c0316640(lo) IPv6 over IPv4 tunneling driver
And here is when acpi is disabled (acpi=off): Linux version 2.6.0 (builder@beton) (gcc version 3.3.1 (PLD Linux)) #1 Mon Sep 8 22:09:34 UTC 2003 Video mode to be used for restore is f07 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000cc000 - 00000000000d0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000000eff0000 (usable) BIOS-e820: 000000000eff0000 - 000000000eff8000 (ACPI data) BIOS-e820: 000000000eff8000 - 000000000f000000 (ACPI NVS) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) 0MB HIGHMEM available. 239MB LOWMEM available. On node 0 totalpages: 61424 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 57328 pages, LIFO batch:13 HighMem zone: 0 pages, LIFO batch:1 DMI 2.3 present. Building zonelist for node : 0 Kernel command line: BOOT_IMAGE=pld-2.6.0 ro root=303 console=ttyS0,57600n81 console=tty0 acpi=off Initializing CPU#0 PID hash table entries: 1024 (order 10: 8192 bytes) Detected 1533.459 MHz processor. Console: colour VGA+ 80x60 Memory: 239664k/245696k available (1662k kernel code, 5336k reserved, 679k data, 164k init, 0k highmem) Calibrating delay loop... 3022.84 BogoMIPS Security Scaffold v1.0.0 initialized SELinux: Not enabled at boot. Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) -> /dev -> /dev/console -> /root CPU: After generic identify, caps: 0383f9ff c1cbf9ff 00000000 00000000 CPU: After vendor identify, caps: 0383f9ff c1cbf9ff 00000000 00000000 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) CPU: After all inits, caps: 0383f9ff c1cbf9ff 00000000 00000020 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: AMD mobile AMD Athlon(tm) XP-M 1800+ stepping 01 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xfdb51, last bus=1 PCI: Using configuration type 1 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20030813 ACPI: Interpreter disabled. Linux Plug and Play Support v0.97 (c) Adam Belay PnPBIOS: Scanning system for PnP BIOS support... PnPBIOS: Found PnP BIOS installation structure at 0xc00f7710 PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x673b, dseg 0xf0000 PnPBIOS: Unknown tag '0x82', length '22'. PnPBIOS: 15 nodes reported by PnP BIOS; 15 recorded by driver ACPI: ACPI tables contain no PCI IRQ routing entries PCI: Invalid ACPI-PCI IRQ routing table PCI: Probing PCI hardware PCI: Probing PCI hardware (bus 00) PCI: Using IRQ router default [1106/8231] at 0000:00:11.0 PCI: IRQ 0 for device 0000:00:08.0 doesn't match PIRQ mask - try pci=usepirqmask pty: 256 Unix98 ptys configured SBF: Simple Boot Flag extension found and enabled. SBF: Setting boot flags 0x1 Machine check exception polling timer started. VFS: Disk quotas dquot_6.5.1 devfs: v1.22 (20021013) Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x0 Initializing Cryptographic API Applying VIA southbridge workaround. isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found w83877f_wdt: WDT driver for W83877F initialised. timeout=30 sec (nowayout=0) Serial: 8250/16550 driver $Revision: 1.90 $ IRQ sharing enabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller at PCI slot 0000:00:11.1 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: VIA vt8231 (rev 10) IDE UDMA100 controller on pci0000:00:11.1 ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio hda: TOSHIBA MK3021GAS, ATA DISK drive Using anticipatory scheduling io scheduler ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hdc: Samsung CD-RW/DVD-ROM SN-324B, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 128KiB hda: 58605120 sectors (30005 MB), CHS=58140/16/63, UDMA(100) /dev/ide/host0/bus0/target0/lun0: p1 p2 p3 mice: PS/2 mouse device common for all mice i8042.c: Detected active multiplexing controller, rev 1.0. serio: i8042 AUX0 port at 0x60,0x64 irq 12 serio: i8042 AUX1 port at 0x60,0x64 irq 12 serio: i8042 AUX2 port at 0x60,0x64 irq 12 serio: i8042 AUX3 port at 0x60,0x64 irq 12 input: AT Set 2 keyboard on isa0060/serio0 serio: i8042 KBD port at 0x60,0x64 irq 1 NET: Registered protocol family 2 IP: routing cache hash table of 2048 buckets, 16Kbytes TCP: Hash tables configured (established 16384 bind 32768) NET: Registered protocol family 1 NET: Registered protocol family 17 BIOS EDD facility v0.09 2003-Jan-22, 1 devices found RAMDISK: Compressed image found at block 0 Freeing initrd memory: 187k freed VFS: Mounted root (romfs filesystem) readonly. EXT3-fs: INFO: recovery required on readonly filesystem. EXT3-fs: write access will be enabled during recovery. kjournald starting. Commit interval 5 seconds EXT3-fs: hda3: orphan cleanup on readonly fs ext3_orphan_cleanup: deleting unreferenced inode 488649 EXT3-fs: hda3: 1 orphan inode deleted EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Trying to move old root to /initrd ... failed Unmounting old root Trying to free ramdisk memory ... okay Freeing unused kernel memory: 164k freed Adding 265064k swap on /dev/hda2. Priority:-1 extents:1 blk: queue c13b2200, I/O limit 4095Mb (mask 0xffffffff) EXT3 FS on hda3, internal journal MCE: The hardware reports a non fatal, correctable incident occurred on CPU 0. Bank 0: 9e5d600000004010 drivers/usb/core/usb.c: registered new driver usbfs drivers/usb/core/usb.c: registered new driver hub end_request: I/O error, dev hdc, sector 0 hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.12 Capability LSM initialized powernow: AMD K7 CPU detected. powernow: PowerNOW! Technology present. Can scale: frequency and voltage. powernow: Found PSB header at c00faf80 powernow: Table version: 0x12 powernow: Flags: 0x0 (Mobile voltage regulator) powernow: Settling Time: 100 microseconds. powernow: Has 86 PST tables. (Only dumping ones relevant to this CPU). powernow: PST:74 (@c00fb590) powernow: cpuid: 0x781 fsb: 133 maxFID: 0x1 startvid: 0xb powernow: FID: 0x6 (6.0x [798MHz]) VID: 0xd (1.350V) powernow: FID: 0x7 (6.5x [864MHz]) VID: 0xd (1.350V) powernow: FID: 0x9 (7.5x [997MHz]) VID: 0xd (1.350V) powernow: FID: 0xb (8.5x [1130MHz]) VID: 0xd (1.350V) powernow: FID: 0xd (9.5x [1263MHz]) VID: 0xd (1.350V) powernow: FID: 0xf (10.5x [1396MHz]) VID: 0xc (1.400V) powernow: FID: 0x1 (11.5x [1529MHz]) VID: 0xb (1.450V)
powernow: Minimum speed 798 MHz. Maximum speed 1529 MHz. input: PS/2 Generic Mouse on isa0060/serio2 NTFS driver 2.1.4 [Flags: R/W MODULE]. NTFS volume version 3.1. Linux Kernel Card Services 3.1.22 options: [pci] [cardbus] [pm] PCI: IRQ 0 for device 0000:00:08.0 doesn't match PIRQ mask - try pci=usepirqmask PCI: No IRQ known for interrupt pin A of device 0000:00:08.0. Please try using pci=biosirq. Yenta: CardBus bridge found at 0000:00:08.0 [1584:3000] Yenta: ISA IRQ list 0820, PCI irq0 Socket status: 30000007 cs: IO port probe 0x0c00-0x0cff: clean. cs: IO port probe 0x0800-0x08ff: excluding 0x800-0x87f cs: IO port probe 0x0100-0x04ff: excluding 0x378-0x37f 0x3c0-0x3df 0x400-0x40f 0x4d0-0x4d7 cs: IO port probe 0x0a00-0x0aff: clean. ohci-hcd: 2003 Feb 24 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ohci-hcd: block sizes: ed 64 td 64 drivers/usb/host/uhci-hcd.c: USB Universal Host Controller Interface driver v2.1 uhci-hcd 0000:00:11.2: UHCI Host Controller uhci-hcd 0000:00:11.2: irq 10, io base 0000d400 uhci-hcd 0000:00:11.2: new USB bus registered, assigned bus number 1 hub 1-0:0: USB hub found hub 1-0:0: 2 ports detected uhci-hcd 0000:00:11.3: UHCI Host Controller uhci-hcd 0000:00:11.3: irq 10, io base 0000d800 uhci-hcd 0000:00:11.3: new USB bus registered, assigned bus number 2 hub 2-0:0: USB hub found hub 2-0:0: 2 ports detected hub 1-0:0: debounce: port 1: delay 100ms stable 4 status 0x301 hub 1-0:0: new USB device on port 1, assigned address 2 drivers/usb/core/usb.c: registered new driver hiddev drivers/usb/input/hid-ff.c: hid_ff_init could not find initializer input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:11.2-1 drivers/usb/core/usb.c: registered new driver hid drivers/usb/input/hid-core.c: v2.0:USB HID core driver drivers/usb/core/usb.c: registered new driver usbmouse drivers/usb/input/usbmouse.c: v1.6:USB HID Boot Protocol mouse driver NET: Registered protocol family 10 Disabled Privacy Extensions on device c0316640(lo) IPv6 over IPv4 tunneling driver
> Unclear why it's now not receiving IRQ 11 ... it's fair to > disable IRQ #11 when there's no IRQ handler for it, but at that > point there is a handler and I'd sure expect it to work. 11 because of that (?): Applying VIA southbridge workaround. PCI: Via IRQ fixup for 0000:00:11.3, from 10 to 11 PCI: Via IRQ fixup for 0000:00:11.2, from 10 to 11 PCI: Via IRQ fixup for 0000:00:11.5, from 10 to 11 PCI: Via IRQ fixup for 0000:00:11.6, from 10 to 11
Maybe another ACPI problem.
> - Dvae
-- Arkadiusz Miśkiewicz CS at FoE, Wroclaw University of Technology arekm.pld-linux.org AM2-6BONE, 1024/3DB19BBD, arekm(at)ircnet, PLD/Linux
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |