lkml.org 
[lkml]   [2003]   [Sep]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [BUG?] SIS IDE DMA errors
On Sat, Sep 27, 2003 at 03:19:37AM +0800, Michael Frank wrote:

> > > 00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev d0) (prog-if 80 [Master])
> > > Subsystem: Asustek Computer, Inc.: Unknown device 1688
> > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> > > Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> > > Latency: 128
> > > Region 4: I/O ports at b800 [size=16]
> > > 00: 39 10 13 55 07 00 00 00 d0 80 01 01 00 80 80 00
> > > 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> > > 20: 01 b8 00 00 00 00 00 00 00 00 00 00 43 10 88 16
> > > 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> > > 40: 31 81 00 00 31 85 00 00 08 01 e6 51 00 02 00 02
> >
> > Ok, this means:
> >
> > 31 - hda: 90ns data active time, 30 ns data recovery time (PIO4)
> > 41 - hda: UDMA enabled, UDMA mode 5 (UDMA100)
> > 00 - hdb: 240ns/360ns (PIO0) - no drive present
> > 00 - hdb: UDMA disabled
> > 31 - hdc: 90ns/30ns PIO4
> > 85 - hdc: UDMA enabled, UDMA mode 2 (UDMA33)
> > 00 - hdd: 240ns/360ns (PIO0) - no drive present
> > 00 - hdd: UDMA disabled
>
> Was running 2.4.22.
>
> Now running 2.6.0-test5. Fresh boot.
>
> 00:0f.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
> Subsystem: Realtek Semiconductor Co., Ltd. RT8139
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (8000ns min, 16000ns max)
> Interrupt: pin A routed to IRQ 11
> Region 0: I/O ports at e000 [size=256]
> Region 1: Memory at eb102000 (32-bit, non-prefetchable) [size=256]
> Expansion ROM at <unassigned> [disabled] [size=64K]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> 00: ec 10 39 81 07 00 90 02 10 00 00 02 00 20 00 00
> 10: 01 e0 00 00 00 20 10 eb 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 ec 10 39 81
> 30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 01 20 40
> 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> I am surprised at your analysis of the pci bus data. By what you
> stated my drive(r) should be doing PIO ;)

1) You're looking at your ethernet controller config registers,
not at the IDE controller config registers.

2) The 961 and 963 have completely different config register layout.
Actually, there is not much common between the 961 and the 963,
except for the '5513' fake ID. (The 961's real id is 5517, and the
963's is 5518).

--
Vojtech Pavlik
SuSE Labs, SuSE CR
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2005-03-22 13:48    [W:0.921 / U:0.012 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site