lkml.org 
[lkml]   [2003]   [Sep]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    Date
    From
    SubjectRe: [2.6.0-test5-mm1] Suspend to RAM problems
    > > Is there an incremental patch from -pm1 to -pm2?
    > > I would apply it to -test5-mm1 then
    >
    > Patch below. Sorry about that.

    Also, no success. It's still the same.

    I also tried with 2.4.22-ac2 with ACPI and also with APM.
    I was only able to APM suspend the machine. Everything else
    did not work :( I also tried without IO-APIC.


    regards, claas


    -------------------
    some logs:
    -------------------

    # cat /proc/interupts
    CPU0
    0: 13882622 IO-APIC-edge timer
    1: 3569 IO-APIC-edge i8042
    2: 0 XT-PIC cascade
    8: 4 IO-APIC-edge rtc
    9: 0 IO-APIC-edge acpi
    12: 35791 IO-APIC-edge i8042
    14: 78195 IO-APIC-edge ide0
    15: 27 IO-APIC-edge ide1
    16: 1043206 IO-APIC-level nvidia
    21: 16 IO-APIC-level ehci_hcd, uhci-hcd, uhci-hcd, uhci-hcd
    22: 0 IO-APIC-level VIA8233
    23: 167984 IO-APIC-level eth0
    NMI: 0
    LOC: 13881222
    ERR: 0
    MIS: 0


    # lspci -v
    00:00.0 Host bridge: VIA Technologies, Inc. VT8377 [KT400 AGP] Host Bridge (rev 80)
    Subsystem: VIA Technologies, Inc. VT8377 [KT400 AGP] Host Bridge
    Flags: bus master, 66Mhz, medium devsel, latency 8
    Memory at d0000000 (32-bit, prefetchable) [size=128M]
    Capabilities: [80] AGP version 3.5
    Capabilities: [c0] Power Management version 2

    00:01.0 PCI bridge: VIA Technologies, Inc.: Unknown device b198 (prog-if 00 [Normal decode])
    Flags: bus master, 66Mhz, medium devsel, latency 0
    Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
    Memory behind bridge: e0000000-e1ffffff
    Prefetchable memory behind bridge: d8000000-dfffffff
    Capabilities: [80] Power Management version 2

    00:10.0 USB Controller: VIA Technologies, Inc. USB (rev 80) (prog-if 00 [UHCI])
    Subsystem: Unknown device 1695:3005
    Flags: bus master, medium devsel, latency 32, IRQ 21
    I/O ports at d000 [size=32]
    Capabilities: [80] Power Management version 2

    00:10.1 USB Controller: VIA Technologies, Inc. USB (rev 80) (prog-if 00 [UHCI])
    Subsystem: Unknown device 1695:3005
    Flags: bus master, medium devsel, latency 32, IRQ 21
    I/O ports at d400 [size=32]
    Capabilities: [80] Power Management version 2

    00:10.2 USB Controller: VIA Technologies, Inc. USB (rev 80) (prog-if 00 [UHCI])
    Subsystem: Unknown device 1695:3005
    Flags: bus master, medium devsel, latency 32, IRQ 21
    I/O ports at d800 [size=32]
    Capabilities: [80] Power Management version 2

    00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82) (prog-if 20 [EHCI])
    Subsystem: Unknown device 1695:3005
    Flags: bus master, medium devsel, latency 32, IRQ 21
    Memory at e2000000 (32-bit, non-prefetchable) [size=256]
    Capabilities: [80] Power Management version 2

    00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
    Subsystem: VIA Technologies, Inc. VT8235 ISA Bridge
    Flags: bus master, stepping, medium devsel, latency 0
    Capabilities: [c0] Power Management version 2

    00:11.1 IDE interface: VIA Technologies, Inc. VT82C586/B/686A/B PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
    Subsystem: Unknown device 1695:3005
    Flags: bus master, medium devsel, latency 32, IRQ 20
    I/O ports at dc00 [size=16]
    Capabilities: [c0] Power Management version 2

    00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233 AC97 Audio Controller (rev 50)
    Subsystem: Unknown device 1695:3005
    Flags: medium devsel, IRQ 22
    I/O ports at e000 [size=256]
    Capabilities: [c0] Power Management version 2

    00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 74)
    Subsystem: Unknown device 1695:3005
    Flags: bus master, medium devsel, latency 32, IRQ 23
    I/O ports at e400 [size=256]
    Memory at e2001000 (32-bit, non-prefetchable) [size=256]
    Capabilities: [40] Power Management version 2

    01:00.0 VGA compatible controller: nVidia Corporation: Unknown device 0322 (rev a1) (prog-if 00 [VGA])
    Subsystem: ABIT Computer Corp.: Unknown device 8f15
    Flags: bus master, 66Mhz, medium devsel, latency 248, IRQ 16
    Memory at e0000000 (32-bit, non-prefetchable) [size=16M]
    Memory at d8000000 (32-bit, prefetchable) [size=128M]
    Expansion ROM at <unassigned> [disabled] [size=128K]
    Capabilities: [60] Power Management version 2
    Capabilities: [44] AGP version 3.0

    # dmesg


    Linux version 2.6.0-test5-mm1 (root@zoo) (gcc version 3.3.2 20030831 (Debian prerelease)) #4 Fri Sep 12 00:01:52 CEST 2003
    Video mode to be used for restore is ffff
    BIOS-provided physical RAM map:
    BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
    BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
    BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
    BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
    BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
    BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
    BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
    BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
    BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
    511MB LOWMEM available.
    found SMP MP-table at 000f5a10
    hm, page 000f5000 reserved twice.
    hm, page 000f6000 reserved twice.
    hm, page 000f1000 reserved twice.
    hm, page 000f2000 reserved twice.
    On node 0 totalpages: 131056
    DMA zone: 4096 pages, LIFO batch:1
    Normal zone: 126960 pages, LIFO batch:16
    HighMem zone: 0 pages, LIFO batch:1
    DMI 2.2 present.
    ACPI: RSDP (v000 KT400A ) @ 0x000f7410
    ACPI: RSDT (v001 KT400A AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3000
    ACPI: FADT (v001 KT400A AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3040
    ACPI: MADT (v001 KT400A AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff7000
    ACPI: DSDT (v001 KT400A AWRDACPI 0x00001000 MSFT 0x0100000d) @ 0x00000000
    ACPI: Local APIC address 0xfee00000
    ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
    Processor #0 6:8 APIC version 16
    ACPI: LAPIC_NMI (acpi_id[0x00] polarity[0x1] trigger[0x1] lint[0x1])
    ACPI: IOAPIC (id[0x02] address[0xfec00000] global_irq_base[0x0])
    IOAPIC[0]: Assigned apic_id 2
    IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, IRQ 0-23
    ACPI: INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x0] trigger[0x0])
    ACPI: INT_SRC_OVR (bus[0] irq[0x9] global_irq[0x9] polarity[0x0] trigger[0x0])
    ACPI: INT_SRC_OVR (bus[0] irq[0xe] global_irq[0xe] polarity[0x1] trigger[0x1])
    ACPI: INT_SRC_OVR (bus[0] irq[0xf] global_irq[0xf] polarity[0x1] trigger[0x1])
    Enabling APIC mode: Flat. Using 1 I/O APICs
    Using ACPI (MADT) for SMP configuration information
    Building zonelist for node : 0
    Kernel command line: root=/dev/hda1 devfs=mount
    current: c04169c0
    current->thread_info: c0474000
    Initializing CPU#0
    PID hash table entries: 2048 (order 11: 16384 bytes)
    Detected 1533.329 MHz processor.
    Console: colour VGA+ 80x25
    Memory: 514172k/524224k available (2715k kernel code, 9304k reserved, 819k data, 352k init, 0k highmem)
    zapping low mappings.
    Calibrating delay loop... 3022.84 BogoMIPS
    Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
    Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
    Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
    -> /dev
    -> /dev/console
    -> /root
    CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000
    CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000
    CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
    CPU: L2 Cache: 256K (64 bytes/line)
    CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000020
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#0.
    CPU: AMD Athlon(tm) XP 1800+ stepping 01
    Enabling fast FPU save and restore... done.
    Enabling unmasked SIMD FPU exception support... done.
    Checking 'hlt' instruction... OK.
    POSIX conformance testing by UNIFIX
    enabled ExtINT on CPU#0
    ESR value before enabling vector: 00000000
    ESR value after enabling vector: 00000000
    ENABLING IO-APIC IRQs
    init IO_APIC IRQs
    IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not connected.
    ..TIMER: vector=0x31 pin1=2 pin2=-1
    number of MP IRQ sources: 15.
    number of IO-APIC #2 registers: 24.
    testing the IO APIC.......................
    IO APIC #2......
    .... register #00: 02000000
    ....... : physical APIC id: 02
    ....... : Delivery Type: 0
    ....... : LTS : 0
    .... register #01: 00178003
    ....... : max redirection entries: 0017
    ....... : PRQ implemented: 1
    ....... : IO APIC version: 0003
    .... IRQ redirection table:
    NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
    00 000 00 1 0 0 0 0 0 0 00
    01 001 01 0 0 0 0 0 1 1 39
    02 001 01 0 0 0 0 0 1 1 31
    03 001 01 0 0 0 0 0 1 1 41
    04 001 01 0 0 0 0 0 1 1 49
    05 001 01 0 0 0 0 0 1 1 51
    06 001 01 0 0 0 0 0 1 1 59
    07 001 01 0 0 0 0 0 1 1 61
    08 001 01 0 0 0 0 0 1 1 69
    09 001 01 0 0 0 0 0 1 1 71
    0a 001 01 0 0 0 0 0 1 1 79
    0b 001 01 0 0 0 0 0 1 1 81
    0c 001 01 0 0 0 0 0 1 1 89
    0d 001 01 0 0 0 0 0 1 1 91
    0e 001 01 0 0 0 0 0 1 1 99
    0f 001 01 0 0 0 0 0 1 1 A1
    10 000 00 1 0 0 0 0 0 0 00
    11 000 00 1 0 0 0 0 0 0 00
    12 000 00 1 0 0 0 0 0 0 00
    13 000 00 1 0 0 0 0 0 0 00
    14 000 00 1 0 0 0 0 0 0 00
    15 000 00 1 0 0 0 0 0 0 00
    16 000 00 1 0 0 0 0 0 0 00
    17 000 00 1 0 0 0 0 0 0 00
    IRQ to pin mappings:
    IRQ0 -> 0:2
    IRQ1 -> 0:1
    IRQ3 -> 0:3
    IRQ4 -> 0:4
    IRQ5 -> 0:5
    IRQ6 -> 0:6
    IRQ7 -> 0:7
    IRQ8 -> 0:8
    IRQ9 -> 0:9
    IRQ10 -> 0:10
    IRQ11 -> 0:11
    IRQ12 -> 0:12
    IRQ13 -> 0:13
    IRQ14 -> 0:14
    IRQ15 -> 0:15
    .................................... done.
    Using local APIC timer interrupts.
    calibrating APIC timer ...
    ..... CPU clock speed is 1532.0959 MHz.
    ..... host bus clock speed is 266.0601 MHz.
    NET: Registered protocol family 16
    PCI: PCI BIOS revision 2.10 entry at 0xfb370, last bus=1
    PCI: Using configuration type 1
    mtrr: v2.0 (20020519)
    ACPI: Subsystem revision 20030813
    ACPI: Interpreter enabled
    ACPI: Using IOAPIC for interrupt routing
    ACPI: PCI Root Bridge [PCI0] (00:00)
    PCI: Probing PCI hardware (bus 00)
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
    ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
    ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
    ACPI: PCI Interrupt Link [ALKA] (IRQs 20)
    ACPI: PCI Interrupt Link [ALKB] (IRQs 21)
    ACPI: PCI Interrupt Link [ALKC] (IRQs 22)
    ACPI: PCI Interrupt Link [ALKD] (IRQs 23)
    Linux Plug and Play Support v0.97 (c) Adam Belay
    SCSI subsystem initialized
    drivers/usb/core/usb.c: registered new driver usbfs
    drivers/usb/core/usb.c: registered new driver hub
    IOAPIC[0]: Set PCI routing entry (2-16 -> 0xa9 -> IRQ 16 Mode:1 Active:1)
    00:00:08[A] -> 2-16 -> IRQ 16
    IOAPIC[0]: Set PCI routing entry (2-17 -> 0xb1 -> IRQ 17 Mode:1 Active:1)
    00:00:08[B] -> 2-17 -> IRQ 17
    IOAPIC[0]: Set PCI routing entry (2-18 -> 0xb9 -> IRQ 18 Mode:1 Active:1)
    00:00:08[C] -> 2-18 -> IRQ 18
    IOAPIC[0]: Set PCI routing entry (2-19 -> 0xc1 -> IRQ 19 Mode:1 Active:1)
    00:00:08[D] -> 2-19 -> IRQ 19
    Pin 2-17 already programmed
    Pin 2-18 already programmed
    Pin 2-19 already programmed
    Pin 2-16 already programmed
    Pin 2-18 already programmed
    Pin 2-19 already programmed
    Pin 2-16 already programmed
    Pin 2-17 already programmed
    Pin 2-19 already programmed
    Pin 2-16 already programmed
    Pin 2-17 already programmed
    Pin 2-18 already programmed
    Pin 2-18 already programmed
    Pin 2-19 already programmed
    Pin 2-16 already programmed
    Pin 2-17 already programmed
    _CRS returns NULL! Using IRQ 21 for device (PCI Interrupt Link [ALKB]).
    ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21
    IOAPIC[0]: Set PCI routing entry (2-21 -> 0xc9 -> IRQ 21 Mode:1 Active:1)
    00:00:10[A] -> 2-21 -> IRQ 21
    Pin 2-21 already programmed
    Pin 2-21 already programmed
    Pin 2-21 already programmed
    _CRS returns NULL! Using IRQ 20 for device (PCI Interrupt Link [ALKA]).
    ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
    IOAPIC[0]: Set PCI routing entry (2-20 -> 0xd1 -> IRQ 20 Mode:1 Active:1)
    00:00:11[A] -> 2-20 -> IRQ 20
    Pin 2-21 already programmed
    _CRS returns NULL! Using IRQ 22 for device (PCI Interrupt Link [ALKC]).
    ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22
    IOAPIC[0]: Set PCI routing entry (2-22 -> 0xd9 -> IRQ 22 Mode:1 Active:1)
    00:00:11[C] -> 2-22 -> IRQ 22
    _CRS returns NULL! Using IRQ 23 for device (PCI Interrupt Link [ALKD]).
    ACPI: PCI Interrupt Link [ALKD] enabled at IRQ 23
    IOAPIC[0]: Set PCI routing entry (2-23 -> 0xe1 -> IRQ 23 Mode:1 Active:1)
    00:00:11[D] -> 2-23 -> IRQ 23
    Pin 2-16 already programmed
    Pin 2-17 already programmed
    Pin 2-18 already programmed
    Pin 2-19 already programmed
    Pin 2-23 already programmed
    Pin 2-23 already programmed
    Pin 2-23 already programmed
    Pin 2-23 already programmed
    PCI: Using ACPI for IRQ routing
    PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
    pty: 256 Unix98 ptys configured
    apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
    apm: overridden by ACPI.
    ikconfig 0.6 with /proc/config*
    devfs: v1.22 (20021013) Richard Gooch (rgooch@atnf.csiro.au)
    devfs: boot_options: 0x1
    udf: registering filesystem
    SGI XFS for Linux with no debug enabled
    Initializing Cryptographic API
    PCI: Via IRQ fixup for 0000:00:10.0, from 11 to 5
    PCI: Via IRQ fixup for 0000:00:10.1, from 11 to 5
    PCI: Via IRQ fixup for 0000:00:10.2, from 10 to 5
    ACPI: Power Button (FF) [PWRF]
    ACPI: Fan [FAN] (on)
    ACPI: Processor [CPU0] (supports C1 C2)
    ACPI: Thermal Zone [THRM] (26 C)
    request_module: failed /sbin/modprobe -- parport_lowlevel. error = -16
    lp: driver loaded but no devices found
    Real Time Clock Driver v1.12
    Serial: 8250/16550 driver $Revision: 1.90 $ IRQ sharing disabled
    ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
    parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
    parport0: irq 7 detected
    parport0: cpp_daisy: aa5500ff(38)
    parport0: assign_addrs: aa5500ff(38)
    parport0: cpp_daisy: aa5500ff(38)
    parport0: assign_addrs: aa5500ff(38)
    lp0: using parport0 (polling).
    Using anticipatory scheduling io scheduler
    Floppy drive(s): fd0 is 1.44M
    FDC 0 is a post-1991 82077
    via-rhine.c:v1.10-LK1.1.19-2.5 July-12-2003 Written by Donald Becker
    http://www.scyld.com/network/via-rhine.html
    eth0: VIA VT6102 Rhine-II at 0xe2001000, 00:04:61:46:e7:38, IRQ 23.
    eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 41e1.
    Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
    ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    VP_IDE: IDE controller at PCI slot 0000:00:11.1
    VP_IDE: chipset revision 6
    VP_IDE: not 100% native mode: will probe irqs later
    ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
    ide0: BM-DMA at 0xdc00-0xdc07, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xdc08-0xdc0f, BIOS settings: hdc:DMA, hdd:pio
    hda: ST3120023A, ATA DISK drive
    ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
    hdc: TOSHIBA DVD-ROM SD-R5112, ATAPI CD/DVD-ROM drive
    ide1 at 0x170-0x177,0x376 on irq 15
    hda: max request size: 128KiB
    hda: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
    /dev/ide/host0/bus0/target0/lun0: p1 p2
    hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
    Uniform CD-ROM driver Revision: 3.12
    ehci_hcd 0000:00:10.3: EHCI Host Controller
    ehci_hcd 0000:00:10.3: irq 21, pci mem e080f000
    ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 1
    ehci_hcd 0000:00:10.3: USB 2.0 enabled, EHCI 1.00, driver 2003-Jun-13
    hub 1-0:0: USB hub found
    hub 1-0:0: 6 ports detected
    drivers/usb/host/uhci-hcd.c: USB Universal Host Controller Interface driver v2.1
    uhci-hcd 0000:00:10.0: UHCI Host Controller
    uhci-hcd 0000:00:10.0: irq 21, io base 0000d000
    uhci-hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
    hub 2-0:0: USB hub found
    hub 2-0:0: 2 ports detected
    uhci-hcd 0000:00:10.1: UHCI Host Controller
    uhci-hcd 0000:00:10.1: irq 21, io base 0000d400
    uhci-hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
    hub 3-0:0: USB hub found
    hub 3-0:0: 2 ports detected
    uhci-hcd 0000:00:10.2: UHCI Host Controller
    uhci-hcd 0000:00:10.2: irq 21, io base 0000d800
    uhci-hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
    hub 4-0:0: USB hub found
    hub 4-0:0: 2 ports detected
    drivers/usb/core/usb.c: registered new driver usblp
    drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
    Initializing USB Mass Storage driver...
    drivers/usb/core/usb.c: registered new driver usb-storage
    USB Mass Storage support registered.
    drivers/usb/core/usb.c: registered new driver hid
    drivers/usb/input/hid-core.c: v2.0:USB HID core driver
    mice: PS/2 mouse device common for all mice
    input: PC Speaker
    input: PS2++ Logitech Wheel Mouse on isa0060/serio1
    serio: i8042 AUX port at 0x60,0x64 irq 12
    input: AT Set 2 keyboard on isa0060/serio0
    serio: i8042 KBD port at 0x60,0x64 irq 1
    Advanced Linux Sound Architecture Driver Version 0.9.6 (Wed Aug 20 20:27:13 2003 UTC).
    request_module: failed /sbin/modprobe -- snd-card-0. error = -16
    PCI: Setting latency timer of device 0000:00:11.5 to 64
    hub 1-0:0: debounce: port 3: delay 100ms stable 4 status 0x501
    hub 3-0:0: debounce: port 1: delay 100ms stable 4 status 0x101
    hub 3-0:0: new USB device on port 1, assigned address 2
    drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 1 proto 2 vid 0x03F0 pid 0x0317
    ALSA device list:
    #0: VIA 8235 at 0xe000, irq 22
    NET: Registered protocol family 2
    IP: routing cache hash table of 4096 buckets, 32Kbytes
    TCP: Hash tables configured (established 32768 bind 65536)
    NET: Registered protocol family 1
    NET: Registered protocol family 17
    NET: Registered protocol family 15
    BIOS EDD facility v0.09 2003-Jan-22, 1 devices found
    PM: Reading swsusp image.
    PM: Resume from disk failed.
    ACPI: (supports S0 S3 S4 S5)
    kjournald starting. Commit interval 5 seconds
    EXT3-fs: mounted filesystem with ordered data mode.
    VFS: Mounted root (ext3 filesystem) readonly.
    Mounted devfs on /dev
    Freeing unused kernel memory: 352k freed
    EXT3 FS on hda1, internal journal
    nvidia: module license 'NVIDIA' taints kernel.
    0: nvidia: loading NVIDIA Linux x86 nvidia.o Kernel Module 1.0-4496 Wed Jul 16 19:03:09 PDT 2003
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on hda2, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    eth0: Setting full-duplex based on MII #1 link partner capability of 41e1.
    -
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

    \
     
     \ /
      Last update: 2005-03-22 13:48    [W:0.047 / U:30.084 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site