[lkml]   [2003]   [Jun]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
Messages in this thread
Subject[PATCHES] 2.4.x net driver updates

BK users may do

bk pull bk://

Others may obtain the patch from

This will update the following files:

drivers/net/bonding.c | 3434 -------------------------
Documentation/ | 9
Documentation/networking/bonding.txt | 537 ++-
Documentation/networking/ifenslave.c | 496 ++-
drivers/net/8139cp.c | 9
drivers/net/8139too.c | 6
drivers/net/ | 3
drivers/net/Makefile | 8
drivers/net/amd8111e.c | 1063 ++++---
drivers/net/amd8111e.h | 968 +++----
drivers/net/arcnet/arcnet.c | 2
drivers/net/arcnet/rfc1201.c | 6
drivers/net/bonding.c | 266 +
drivers/net/bonding/Makefile | 18
drivers/net/bonding/bond_3ad.c | 2667 ++++++++++++++++++-
drivers/net/bonding/bond_3ad.h | 342 ++
drivers/net/bonding/bond_alb.c | 1585 +++++++++++
drivers/net/bonding/bond_alb.h | 129
drivers/net/bonding/bond_main.c | 4795 ++++++++++++++++++++++++++++++++---
drivers/net/bonding/bonding.h | 209 +
drivers/net/dl2k.h | 1
drivers/net/e1000/e1000.h | 3
drivers/net/e1000/e1000_main.c | 167 +
drivers/net/eepro.c | 2
drivers/net/ns83820.c | 2
drivers/net/pci-skeleton.c | 4
drivers/net/pcnet32.c | 7
drivers/net/r8169.c | 52
drivers/net/sk98lin/skge.c | 2
drivers/net/sundance.c | 144 -
drivers/net/tg3.c | 2
drivers/net/tlan.c | 258 +
drivers/net/tlan.h | 7
drivers/net/tokenring/olympic.c | 3
drivers/net/tulip/tulip_core.c | 7
drivers/net/typhoon.c | 4
drivers/net/via-rhine.c | 2
drivers/net/wireless/airo.c | 2
include/linux/ethtool.h | 27
include/linux/if_arcnet.h | 4
include/linux/if_bonding.h | 101
include/linux/if_vlan.h | 1
include/linux/skbuff.h | 4
include/net/if_inet6.h | 5
include/net/irda/irlan_common.h | 2
net/core/dev.c | 4
net/core/skbuff.c | 3
net/ipv6/addrconf.c | 13
net/ipv6/ndisc.c | 3
net/irda/irlan/irlan_eth.c | 6
50 files changed, 11856 insertions(+), 5538 deletions(-)

through these ChangeSets:

<> (03/06/06 1.1205)
[PATCH] Bonding 2.4 update patch 6

Fix to the ifenslave -c fix, fix to version control (plus
change log update). I've got an additional fix for version control
that I'll send you on Monday.

Index: linux-2.4.21-rc6-netdrvr1/Documentation/networking/ifenslave.c

<> (03/06/06 1.1204)
[PATCH] Bonding 2.4 update patch 5

Fix to prevent routes on the bonding device from being lost
during enslavement processing.

Index: linux-2.4.21-rc6-netdrvr1/Documentation/networking/ifenslave.c

<> (03/06/06 1.1203)
[PATCH] Bonding 2.4 update patch 4

A fix for ifenslave -c. Later patches have fixes for this fix.

Index: linux-2.4.21-rc6-netdrvr1/Documentation/networking/ifenslave.c

<> (03/06/06 1.1202)
[PATCH] Bonding 2.4 update patch 3

A patch with some miscellaneous little stuff (comments, mode
names, fix a printk).

Index: linux-2.4.21-rc6-netdrvr1/drivers/net/bonding/bond_main.c

<> (03/06/06 1.1201)
[PATCH] Bonding 2.4 update patch 2

Small patch to fix endless failover problem in the ARP monitor.

Index: linux-2.4.21-rc6-netdrvr1/drivers/net/bonding/bond_main.c

<> (03/06/06 1.1200)
[PATCH] Bonding 2.4 update patch 1


Index: linux-2.4.21-rc6-netdrvr1/Documentation/networking/bonding.txt

<> (03/06/06 1.1199)
[PATCH] remove ethtool privileged references

dev_ioctl already checks capable(CAP_NET_ADMIN) for SOICETHTOOL, so
privileged reference are not necessary.

<> (03/06/06 1.1198)
[PATCH] 10GbE ethtool support

Add 10GbE support for ethtool.

<> (03/06/05 1.1197)
[netdrvr amd8111e] link against mii lib

<> (03/06/04 1.1196)
[netdrvr] gcc 3.3 cleanups

Mostly marking 64-bit constants as ULL.

<> (03/05/29 1.1185.1.52)
[netdrvr amd8111e] remove out-of-tree feature that snuck in

<> (03/05/29 1.1185.1.51)
[netdrvr amd8111e] interrupt coalescing, libmii, bug fixes

* Dynamic interrupt coalescing
* mii lib support
* dynamic IPG support (disabled by default)
* jumbo frame fix
* vlan fix
* rx irq coalescing fix

<> (03/05/29 1.1185.1.50)
[netdrvr tlan] fix 64-bit issues

<> (03/05/29 1.1185.1.49)
[netdrvr r8169] sync with 2.5 (backport whitespace cleanups)

<> (03/05/29 1.1185.1.48)
[netdrvr r8169] use alloc_etherdev (fix race), pci_disable_device

<> (03/05/29 1.1185.1.47)
[netdrvr olympic] fix build with gcc 3.3

<> (03/05/29 1.1185.6.3)
[netdrvr 8139too] add comment, whitespace cleanup

<> (03/05/28 1.1185.6.2)
[netdrvr] s/init_etherdev/alloc_etherdev/ in code comments,
in 8139too and pci-skeleton drivers.

<> (03/05/28 1.1185.6.1)
[netdrvr tlan] backport fixes and cleanups from 2.5

* alloc_etherdev (fixes race)
* C99 initializers
* speling fixes
* use pci_{request,release}_regions for PCI devices
* propagate error returns back from pci_xxx functions
* call pci_set_dma_mask
* use keventd for adapter error reset (2.5 uses workqueue)

<> (03/05/27 1.1185.1.45)
[netdrvr pcnet32] bug fixes

I would like to see a couple of the pcnet32 changes that I think we can
agree on be put into the trees so a couple of the potential defects can be
avoided. The following patch contains just these pieces. The only
controversial one is an arbitrary change in the number of iterations in a
while loop spinning on hardware state. No matter how this is done, I am
not especially fond of this bit of code as it has no reasonable error
recovery path -- however, as a half-way, incremental solution, increasing
the polling time should help as the 100 value was certainly found to be
insufficient. 1000 may not be sufficient either, but it is certainly no

Both of the other changes were hit in testing (and I belive the wmb() at a
customer even), so it would help reduce some debug if these go in. Any
feedback is appreciated - thanks.

<> (03/05/27 1.1185.1.44)
[netdrvr eepro] update MODULE_AUTHOR per old-author request

<> (03/05/27 1.1185.1.43)
[netdrvr sundance] fix another flow control bug

<> (03/05/27 1.1185.1.42)
[netdrvr sundance] fix flow control bug

<> (03/05/27 1.1185.1.41)
[netdrvr bonding] fix ABI version control problem

This fix makes bonding not commit to a specific ABI version if the ioctl
command is not supported by bonding.

(It also removes the '\n' in the continuous printk reporting the link down
event in bond_mii_monitor - it got in there by mistake in our previous
patch set and caused log messages to appear funny in some situations).

<> (03/05/27 1.1185.1.40)
[netdrvr bonding] fix long failover in 802.3ad mode

This patch fixes the bug reported by Jay on April 3rd regarding long
failover time when releasing the last slave in the active aggregator. The
fix, as suggested by Jay, is to follow the spec recommendation and send a
LACPDU to the partner saying this port is no longer aggregatable and
therefore trigger an immediate re-selection of a new aggregator instead of
waiting the entire expiration timeout.

<> (03/05/25 1.1185.1.39)
IPv6 over ARCnet (RFC2497) support, IPv6 part.

<> (03/05/25 1.1185.1.38)
IPv6 over ARCnet (RFC2497) support, driver part

<> (03/05/25 1.1185.1.37)
[irda] module refcounts for irlan

<> (03/05/23 1.1185.3.7)
[bonding] small cleanups

<> (03/05/23 1.1185.3.6)
[bonding] add rcv load balancing mode

This patch adds a new mode that enables receive load balancing for IPv4
traffic on top of the transmit load balancing mode. This capability is
achieved by intercepting and manipulating the ARP negotiation to teach
clients several MAC addresses for the bond and thus distribute incoming
traffic among all slaves with the highest link speed.

In order to function properly, slaves are required to be able to have
their MAC address set even while the interface is up since once the
primary slave looses its link, the new primary slave (and only it) must be
able to take over and receive the incoming traffic instead. If a
non-primary slave looses its link, ARP packets will be sent to all clients
communicating through it in order to teach them a replacement MAC address,
and the primary slave will be put in promiscuous mode for 10 seconds for
fault tolerance reasons.

This patch is against bonding-20030415, but must come only after the
locking scheme changing patch since it uses dev_set_promiscuity() that
would otherwise cause a system hang.

<> (03/05/23 1.1185.3.5)
[bonding] support xmit load balancing mode

<> (03/05/23 1.1185.3.4)
[bonding] much improved locking

This patch replaces the use of lock_irqsave/unlock_irqrestore in bonding
with lock/unlock or lock_bh/unlock_bh as appropriate according to context.
This change is based on a previous discussion regarding the fact that
holding a lock_irqsave doesn't prevent softirqs from running which can
cause deadlocks in certain situations. This new locking scheme has already
undergone massive testing cycle by our QA group and we feel it is ready
for release (some new modes and enhancements will not work properly
without it).

<> (03/05/23 1.1185.3.3)
[bonding] better 802.3ad mode control, some cleanup

This patch adds the lacp_rate module param to enable better control over
the IEEE 802.3ad mode. This param controls the rate at which the partner
system is asked to send LACPDUs to bonding.
Two options exist:
- slow (or 0) - LACPDUs are 30 seconds apart
- fast (or 1) - LACPDUs are 1 second apart
The default is slow (like most switches around).

There are also some code beautifications (mainly converting comments to C
style in code segments we added in the past).

<> (03/05/23 1.1185.3.2)
[bonding] ABI versioning

This patch adds user-land to kernel ABI version control in bonding to
restore backward compatibility between different versions of ifenslave and
the bonding module. It uses ethtool's GDRVINFO ioctl to pass the ABI
version number between ifenslave and the bonding module in both directions
so both the driver and the application can tell which partner they're
working against and take the appropriate measures when enslaving/releasing
an interface. The bonding module remembers the ABI version received from
the application, and from that moment on will deny enslave and release
commands from an application using a different ABI version, which means
that if you want to switch to an ifenslave with a different ABI version
(or with non at all), you'll first have to re-load the bonding module.

This patch also changes the driver/application versioning scheme to
contain 3 fields X.Y.Z with the follows meaning:
X - Major version - big behavior changes
Y - Minor version - addition of features
Z - Extra version - minor changes and bug fixes

There are also three minor bug fixes:
1. Prevent enslaving an interface that is already a slave.
2. Prevent enslaving if the bond is down.
3. In bond_release_all, save old value of current_slave before assigning
NULL to it to enable using it's original value later on.

This patch is against bonding-20030415.

<> (03/04/27 1.1137.1.6)
[netdrvr e1000] add TSO support -- disabled

* Copy TSO support for 2.5 e1000. Wrapped with NETIF_F_TSO, so
not currently enabled in 2.4. Done to keep 2.4 and 2.5 drivers
in-sync as much as possible.

<> (03/04/27 1.1137.1.5)
[netdrvr e1000] add support for NAPI

* Copy NAPI support from 2.5 e1000 driver
* Add CONFIG_E1000_NAPI option

<> (03/04/27 1.1137.1.4)
[netdrvr tulip] support DM910x chip from ALi

<> (03/04/27 1.1137.1.3)
Remove duplicate CONFIG_TULIP_MWI entry in

Noticed by Geert Uytterhoeven

<> (03/04/27 1.1137.1.2)
[netdrvr 8139cp] enable MWI via pci_set_mwi, rather than manually

<> (03/04/26 1.1131.2.6)
[netdrvr typhoon] s/#if/#ifdef/ for a CONFIG_ var

<> (03/04/25 1.1131.2.5)
[netdrvr sundance] small cleanups from 2.5

- s/long flag/unsigned long flag/
- C99 initializers

<> (03/04/25 1.1131.2.4)
[netdrvr sundance] bug fixes, VLAN support

- Fix tx bugs in big-endian machines
- Remove unused max_interrupt_work module parameter, the new
NAPI-like rx scheme doesn't need it.
- Remove redundancy get_stats() in intr_handler(), those
I/O access could affect performance in ARM-based system
- Add Linux software VLAN support
- Fix bug of custom mac address
(StationAddr register only accept word write)

<> (03/04/25 1.1131.2.3)
[netdrvr via-rhine] fix promisc mode

I found a via-rhine bug, it can't receive BPDU (mac: 0180c2000000)
in promiscuous mode.
Fill all "1" in hash table to fix this problem in promiscuous mode.
(RCR remain 0x1c, write it as 0x1f don't work)

<> (03/04/25 1.1131.2.2)
[wireless airo] fix end-of-array test

FYI statsLabels[] is an array of char*, so the fix below
is pretty obvious.

<> (03/04/25 1.1131.2.1)
[PATCH] fix .text.exit error in drivers/net/r8169.c

In drivers/net/r8169.c the function rtl8169_remove_one is __devexit but
the pointer to it didn't use __devexit_p resulting in a.text.exit
compile error when !CONFIG_HOTPLUG.

The fix is simple:

<> (03/04/17 1.1101.8.7)
[bonding] add support for IEEE 802.3ad Dynamic link aggregation

Contributed by Shmulik Hen @ Intel, merge by Jay Vosburgh @ IBM

<> (03/04/17 1.1101.8.6)
[bonding] move private decls into new drv/net/bonding/bonding.h file

<> (03/04/17 1.1101.8.5)
[bonding] move driver into new drivers/net/bonding directory

<> (03/04/17 1.1101.8.4)
[bonding] Moved setting slave mac addr, and open, from app to the driver

This patch enables support of modes that need to use the unique mac
address of each slave. It moves setting the slave's mac address and
opening it from the application to the driver.
This breaks backward compatibility between the new driver and older
applications !
It also blocks possibility of enslaving before the master is up (to
prevent putting the system in an unstable state), and removes the code
that unconditionally restores all base driver's flags (flags are
automatically restored once all undo stages are done in proper order).

Contributed by Shmulik Hen @ Intel

<> (03/04/17 1.1101.8.3)
[bonding] add support for getting slave's speed and duplex via ethtool

Contributed by Shmulik Hen @ Intel

<> (03/04/17 1.1101.8.2)
[bonding] fix comment to prevent future merge difficulties

Contributed by Jay Vosburgh @ IBM

<> (03/04/17 1.1101.8.1)
[net] store physical device a packet arrives in on

(Needed for bonding)

Contributed by Jay Vosburgh @ IBM, Shmulik Hen @ Intel, and others.

To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to
More majordomo info at
Please read the FAQ at

 \ /
  Last update: 2005-03-22 13:36    [W:0.037 / U:34.864 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site