Messages in this thread |  | | | Date | Mon, 14 Apr 2003 08:38:08 +0100 (BST) | | Subject | Re: PCI: Device 02:04.0 not available because of resource collisions | | From | <> |
| |
> The output of: > > lspci -vv > cat /proc/iomem > cat /proc/ioports > > from both a working and non-working kernel would be most helpful (along > with the kernel versions used.)
Hi Russel,
Right I have the information you wanted...(I think ;) I wasent sure what you meant by working/non-working kernels. I only have a 2.4.20 and 2.5.67 installed and neither of them work with the Cardbus Controller. Anyway I will include the output for both (so appologies for the length of this email)
This is for kernel version:
# uname -a Linux cerberus.savagelandz.cjb.net 2.4.20-xfs-r2 #1 SMP Sun Apr 13 08:58:11 BST 2003 i686 Pentium III (Katmai) GenuineIntel GNU/Linux
# lspci -vv 00:00.0 Host bridge: Intel Corp. 440GX - 82443GX Host bridge Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 64 Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M] Capabilities: [a0] AGP version 1.0 Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2 Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none> 00:01.0 PCI bridge: Intel Corp. 440GX - 82443GX AGP bridge (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Bus: primary=00, secondary=01, subordinate=02, sec-latency=64 BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B+
00:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Unex Technology Corp. ND010 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (8000ns min, 16000ns max) Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at 2400 [size=256] Region 1: Memory at f4101000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0c.0 SCSI storage controller: Adaptec AIC-7896U2/7897U2 Subsystem: Adaptec: Unknown device 0053 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (9750ns min, 6250ns max), cache line size 08 Interrupt: pin A routed to IRQ 19 BIST result: 00 Region 0: I/O ports at 2800 [disabled] [size=256] Region 1: Memory at f4102000 (64-bit, non-prefetchable) [size=4K] Expansion ROM at <unassigned> [disabled] [size=128K] Capabilities: [dc] Power Management version 1 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0c.1 SCSI storage controller: Adaptec AIC-7896U2/7897U2 Subsystem: Adaptec: Unknown device 0053 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (9750ns min, 6250ns max), cache line size 08 Interrupt: pin A routed to IRQ 19 BIST result: 00 Region 0: I/O ports at 2c00 [disabled] [size=256] Region 1: Memory at f4103000 (64-bit, non-prefetchable) [size=4K] Capabilities: [dc] Power Management version 1 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0d.0 Multimedia video controller: Brooktree Corporation Bt848 Video Capture (rev 12) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (4000ns min, 10000ns max) Interrupt: pin A routed to IRQ 17 Region 0: Memory at f4105000 (32-bit, prefetchable) [size=4K] 00:0e.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 08) Subsystem: Intel Corp. EtherExpress PRO/100+ Management Adapter Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (2000ns min, 14000ns max), cache line size 08 Interrupt: pin A routed to IRQ 21 Region 0: Memory at f4100000 (32-bit, non-prefetchable) [size=4K] Region 1: I/O ports at 2000 [size=64] Region 2: Memory at f4000000 (32-bit, non-prefetchable) [size=1M] Expansion ROM at <unassigned> [disabled] [size=1M] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=2 PME- 00:12.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0
00:12.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) (prog-if 80 [Master]) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Region 0: [virtual] I/O ports at 01f0 Region 1: [virtual] I/O ports at 03f4 Region 2: [virtual] I/O ports at 0170 Region 3: [virtual] I/O ports at 0374 Region 4: I/O ports at 2040 [size=16]
00:12.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) (prog-if 00 [UHCI]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Interrupt: pin D routed to IRQ 21 Region 4: I/O ports at 2060 [disabled] [size=32]
00:12.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02) Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin ? routed to IRQ 9
00:14.0 VGA compatible controller: Cirrus Logic GD 5480 (rev 23) (prog-if 00 [VGA]) Subsystem: Cirrus Logic CL-GD5480 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (500ns min, 2500ns max) Region 0: Memory at f6000000 (32-bit, prefetchable) [size=32M] Region 1: Memory at f4104000 (32-bit, non-prefetchable) [size=4K] Expansion ROM at <unassigned> [disabled] [size=32K] 01:0f.0 PCI bridge: Digital Equipment Corporation DECchip 21150 (rev 06) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B+ Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 240, cache line size 08 Bus: primary=01, secondary=02, subordinate=02, sec-latency=68 BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- Capabilities: [dc] Power Management version 1 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Bridge: PM- B3+
02:04.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus Controller (rev 01) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin A routed to IRQ 20 Region 0: Memory at <unassigned> (32-bit, non-prefetchable) [disabled] [size=4K] Bus: primary=02, secondary=03, subordinate=06, sec-latency=0 I/O window 0: 00000000-00000003 [disabled] I/O window 1: 00000000-00000003 [disabled] BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt- PostWrite- 16-bit legacy interface ports at 0001
# cat /proc/iomem 00000000-0009f3ff : System RAM 0009f400-0009ffff : reserved 000a0000-000bffff : Video RAM area 000c0000-000c7fff : Video ROM 000c8000-000cdfff : Extension ROM 000ce000-000cf7ff : Extension ROM 000f0000-000fffff : System ROM 00100000-0ffeffff : System RAM 00100000-003b0130 : Kernel code 003b0131-0045cae3 : Kernel data 0fff0000-0ffffbff : ACPI Tables 0ffffc00-0fffffff : ACPI Non-volatile Storage f4000000-f40fffff : Intel Corp. 82557/8/9 [Ethernet Pro 100] f4000000-f40fffff : e100 f4100000-f4100fff : Intel Corp. 82557/8/9 [Ethernet Pro 100] f4100000-f4100fff : e100 f4101000-f41010ff : Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ f4101000-f41010ff : 8139too f4102000-f4102fff : Adaptec AIC-7896U2/7897U2 f4102000-f4102fff : aic7xxx f4103000-f4103fff : Adaptec AIC-7896U2/7897U2 (#2) f4103000-f4103fff : aic7xxx f4104000-f4104fff : Cirrus Logic GD 5480 f4105000-f4105fff : Brooktree Corporation Bt848 Video Capture f4105000-f4105fff : bttv f6000000-f7ffffff : Cirrus Logic GD 5480 f8000000-fbffffff : Intel Corp. 440GX - 82443GX Host bridge fec00000-fec0ffff : reserved fee00000-fee00fff : reserved fff80000-ffffffff : reserved # cat /proc/ioports 0000-001f : dma1 0020-003f : pic1 0040-005f : timer 0060-006f : keyboard 0070-007f : rtc 0080-008f : dma page reg 00a0-00bf : pic2 00c0-00df : dma2 00f0-00ff : fpu 0170-0177 : ide1 01f0-01f7 : ide0 0213-0213 : isapnp read 0220-022f : SoundBlaster 02f8-02ff : serial(auto) 0330-0331 : MPU401 UART 0376-0376 : ide1 0388-0389 : OPL2/3 (left) 038a-038b : OPL2/3 (right) 03c0-03df : vga+ 03f6-03f6 : ide0 03f8-03ff : serial(auto) 0620-0623 : Emu8000-1 0a20-0a23 : Emu8000-2 0a79-0a79 : isapnp write 0c00-0c3f : Intel Corp. 82371AB/EB/MB PIIX4 ACPI 0cf8-0cff : PCI conf1 0e20-0e23 : Emu8000-3 1040-105f : Intel Corp. 82371AB/EB/MB PIIX4 ACPI 2000-203f : Intel Corp. 82557/8/9 [Ethernet Pro 100] 2000-203f : e100 2040-204f : Intel Corp. 82371AB/EB/MB PIIX4 IDE 2040-2047 : ide0 2048-204f : ide1 2060-207f : Intel Corp. 82371AB/EB/MB PIIX4 USB 2400-24ff : Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ 2400-24ff : 8139too 2800-28ff : Adaptec AIC-7896U2/7897U2 2c00-2cff : Adaptec AIC-7896U2/7897U2 (#2) I also noticed this in the dmesg output...
PCI: Using ACPI for IRQ routing PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off' PCI: Failed to allocate resource 0(0-fff) for 02:04.0
Ok Below is all the same stuff from the 2.5.67 kernel
# uname -a Linux cerberus.savagelandz.cjb.net 2.5.67 #1 SMP Fri Apr 11 12:37:43 BST 2003 i686 Pentium III (Katmai) GenuineIntel GNU/Linux
# lspci -vv 00:00.0 Host bridge: Intel Corp. 440GX - 82443GX Host bridge Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 64 Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M] Capabilities: [a0] AGP version 1.0 Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2 Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none> 00:01.0 PCI bridge: Intel Corp. 440GX - 82443GX AGP bridge (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Bus: primary=00, secondary=01, subordinate=02, sec-latency=64 BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B+
00:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Unex Technology Corp. ND010 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (8000ns min, 16000ns max) Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at 2400 [size=256] Region 1: Memory at f4101000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0c.0 SCSI storage controller: Adaptec AIC-7896U2/7897U2 Subsystem: Adaptec: Unknown device 0053 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (9750ns min, 6250ns max), cache line size 08 Interrupt: pin A routed to IRQ 19 BIST result: 00 Region 0: I/O ports at 2800 [disabled] [size=256] Region 1: Memory at f4102000 (64-bit, non-prefetchable) [size=4K] Expansion ROM at <unassigned> [disabled] [size=128K] Capabilities: [dc] Power Management version 1 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0c.1 SCSI storage controller: Adaptec AIC-7896U2/7897U2 Subsystem: Adaptec: Unknown device 0053 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (9750ns min, 6250ns max), cache line size 08 Interrupt: pin A routed to IRQ 19 BIST result: 00 Region 0: I/O ports at 2c00 [disabled] [size=256] Region 1: Memory at f4103000 (64-bit, non-prefetchable) [size=4K] Capabilities: [dc] Power Management version 1 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0d.0 Multimedia video controller: Brooktree Corporation Bt848 Video Capture (rev 12) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (4000ns min, 10000ns max) Interrupt: pin A routed to IRQ 17 Region 0: Memory at f4105000 (32-bit, prefetchable) [size=4K] 00:0e.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 08) Subsystem: Intel Corp. EtherExpress PRO/100+ Management Adapter Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (2000ns min, 14000ns max), cache line size 08 Interrupt: pin A routed to IRQ 21 Region 0: Memory at f4100000 (32-bit, non-prefetchable) [size=4K] Region 1: I/O ports at 2000 [size=64] Region 2: Memory at f4000000 (32-bit, non-prefetchable) [size=1M] Expansion ROM at <unassigned> [disabled] [size=1M] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=2 PME- 00:12.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0
00:12.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) (prog-if 80 [Master]) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Region 4: I/O ports at 2040 [size=16]
00:12.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) (prog-if 00 [UHCI]) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Interrupt: pin D routed to IRQ 21 Region 4: I/O ports at 2060 [size=32]
00:12.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02) Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin ? routed to IRQ 9
00:14.0 VGA compatible controller: Cirrus Logic GD 5480 (rev 23) (prog-if 00 [VGA]) Subsystem: Cirrus Logic CL-GD5480 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (500ns min, 2500ns max) Region 0: Memory at f6000000 (32-bit, prefetchable) [size=32M] Region 1: Memory at f4104000 (32-bit, non-prefetchable) [size=4K] Expansion ROM at <unassigned> [disabled] [size=32K] 01:0f.0 PCI bridge: Digital Equipment Corporation DECchip 21150 (rev 06) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B+ Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 240, cache line size 08 Bus: primary=01, secondary=02, subordinate=02, sec-latency=68 BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- Capabilities: [dc] Power Management version 1 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Bridge: PM- B3+
02:04.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus Controller (rev 01) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin A routed to IRQ 20 Region 0: Memory at <unassigned> (32-bit, non-prefetchable) [disabled] [size=4K] Bus: primary=02, secondary=03, subordinate=06, sec-latency=176 I/O window 0: 00000000-00000003 [disabled] I/O window 1: 00000000-00000003 [disabled] BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt- PostWrite- 16-bit legacy interface ports at 0001 # cat /proc/iomem 00000000-0009f3ff : System RAM 0009f400-0009ffff : reserved 000a0000-000bffff : Video RAM area 000c0000-000c7fff : Video ROM 000c8000-000cdfff : Extension ROM 000ce000-000cf7ff : Extension ROM 000f0000-000fffff : System ROM 00100000-0ffeffff : System RAM 00100000-00441c26 : Kernel code 00441c27-0054af5f : Kernel data 0fff0000-0ffffbff : ACPI Tables 0ffffc00-0fffffff : ACPI Non-volatile Storage f4000000-f40fffff : Intel Corp. 82557/8/9 [Ethernet f4000000-f40fffff : e100 f4100000-f4100fff : Intel Corp. 82557/8/9 [Ethernet f4100000-f4100fff : e100 f4101000-f41010ff : Realtek Semiconducto RTL-8139/8139C/8139C f4101000-f41010ff : 8139too f4102000-f4102fff : Adaptec AIC-7896U2/7897U2 f4102000-f4102fff : aic7xxx f4103000-f4103fff : Adaptec AIC-7896U2/7897U2 (#2) f4103000-f4103fff : aic7xxx f4104000-f4104fff : Cirrus Logic GD 5480 f4105000-f4105fff : Brooktree Corporatio Bt848 Video Capture f4105000-f4105fff : bttv0 f6000000-f7ffffff : Cirrus Logic GD 5480 f8000000-fbffffff : Intel Corp. 440GX - 82443GX Host fec00000-fec0ffff : reserved fee00000-fee00fff : reserved fff80000-ffffffff : reserved # cat /proc/ioports 0000-001f : dma1 0020-003f : pic1 0040-005f : timer 0060-006f : keyboard 0070-0077 : rtc 0080-008f : dma page reg 00a0-00bf : pic2 00c0-00df : dma2 00f0-00ff : fpu 0170-0177 : ide1 01f0-01f7 : ide0 0213-0213 : isapnp read 02f8-02ff : serial 0376-0376 : ide1 0378-037a : parport0 037b-037f : parport0 03c0-03df : vga+ 03f6-03f6 : ide0 03f8-03ff : serial 0a79-0a79 : isapnp write 0c00-0c3f : Intel Corp. 82371AB/EB/MB PIIX4 0cf8-0cff : PCI conf1 1040-105f : Intel Corp. 82371AB/EB/MB PIIX4 1040-1047 : piix4-smbus 2000-203f : Intel Corp. 82557/8/9 [Ethernet 2000-203f : e100 2040-204f : Intel Corp. 82371AB/EB/MB PIIX4 2040-2047 : ide0 2048-204f : ide1 2060-207f : Intel Corp. 82371AB/EB/MB PIIX4 2060-207f : uhci-hcd 2400-24ff : Realtek Semiconducto RTL-8139/8139C/8139C 2400-24ff : 8139too 2800-28ff : Adaptec AIC-7896U2/7897U2 2c00-2cff : Adaptec AIC-7896U2/7897U2 (#2) Hope all this helps.
Regards
iain
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
|  |