lkml.org 
[lkml]   [2003]   [Mar]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
Subject[PATCH 2.5.65-ac4] Complete support for PC-9800 sub-arch (3/9) DMA
This is the patch to support NEC PC-9800 subarchitecture
against 2.5.65-ac4. (3/9)

DMA support for PC98.
For fix differences of IO port assign and memory addressing.
PC98 has 'page register' to expand DMA accesible address.

Regards,
Osamu Tomita

diff -Nru linux/include/asm-i386/dma.h linux98/include/asm-i386/dma.h
--- linux/include/asm-i386/dma.h 2003-03-05 12:29:19.000000000 +0900
+++ linux98/include/asm-i386/dma.h 2003-03-17 15:24:26.000000000 +0900
@@ -1,298 +1,10 @@
-/* $Id: dma.h,v 1.7 1992/12/14 00:29:34 root Exp root $
- * linux/include/asm/dma.h: Defines for using and allocating dma channels.
- * Written by Hennus Bergman, 1992.
- * High DMA channel support & info by Hannu Savolainen
- * and John Boyd, Nov. 1992.
- */
-
#ifndef _ASM_DMA_H
#define _ASM_DMA_H

-#include <linux/config.h>
-#include <linux/spinlock.h> /* And spinlocks */
-#include <asm/io.h> /* need byte IO */
-#include <linux/delay.h>
-
-
-#ifdef HAVE_REALLY_SLOW_DMA_CONTROLLER
-#define dma_outb outb_p
-#else
-#define dma_outb outb
-#endif
-
-#define dma_inb inb
-
-/*
- * NOTES about DMA transfers:
- *
- * controller 1: channels 0-3, byte operations, ports 00-1F
- * controller 2: channels 4-7, word operations, ports C0-DF
- *
- * - ALL registers are 8 bits only, regardless of transfer size
- * - channel 4 is not used - cascades 1 into 2.
- * - channels 0-3 are byte - addresses/counts are for physical bytes
- * - channels 5-7 are word - addresses/counts are for physical words
- * - transfers must not cross physical 64K (0-3) or 128K (5-7) boundaries
- * - transfer count loaded to registers is 1 less than actual count
- * - controller 2 offsets are all even (2x offsets for controller 1)
- * - page registers for 5-7 don't use data bit 0, represent 128K pages
- * - page registers for 0-3 use bit 0, represent 64K pages
- *
- * DMA transfers are limited to the lower 16MB of _physical_ memory.
- * Note that addresses loaded into registers must be _physical_ addresses,
- * not logical addresses (which may differ if paging is active).
- *
- * Address mapping for channels 0-3:
- *
- * A23 ... A16 A15 ... A8 A7 ... A0 (Physical addresses)
- * | ... | | ... | | ... |
- * | ... | | ... | | ... |
- * | ... | | ... | | ... |
- * P7 ... P0 A7 ... A0 A7 ... A0
- * | Page | Addr MSB | Addr LSB | (DMA registers)
- *
- * Address mapping for channels 5-7:
- *
- * A23 ... A17 A16 A15 ... A9 A8 A7 ... A1 A0 (Physical addresses)
- * | ... | \ \ ... \ \ \ ... \ \
- * | ... | \ \ ... \ \ \ ... \ (not used)
- * | ... | \ \ ... \ \ \ ... \
- * P7 ... P1 (0) A7 A6 ... A0 A7 A6 ... A0
- * | Page | Addr MSB | Addr LSB | (DMA registers)
- *
- * Again, channels 5-7 transfer _physical_ words (16 bits), so addresses
- * and counts _must_ be word-aligned (the lowest address bit is _ignored_ at
- * the hardware level, so odd-byte transfers aren't possible).
- *
- * Transfer count (_not # bytes_) is limited to 64K, represented as actual
- * count - 1 : 64K => 0xFFFF, 1 => 0x0000. Thus, count is always 1 or more,
- * and up to 128K bytes may be transferred on channels 5-7 in one operation.
- *
- */
-
-#define MAX_DMA_CHANNELS 8
-
-/* The maximum address that we can perform a DMA transfer to on this platform */
-#define MAX_DMA_ADDRESS (PAGE_OFFSET+0x1000000)
-
-/* 8237 DMA controllers */
-#define IO_DMA1_BASE 0x00 /* 8 bit slave DMA, channels 0..3 */
-#define IO_DMA2_BASE 0xC0 /* 16 bit master DMA, ch 4(=slave input)..7 */
-
-/* DMA controller registers */
-#define DMA1_CMD_REG 0x08 /* command register (w) */
-#define DMA1_STAT_REG 0x08 /* status register (r) */
-#define DMA1_REQ_REG 0x09 /* request register (w) */
-#define DMA1_MASK_REG 0x0A /* single-channel mask (w) */
-#define DMA1_MODE_REG 0x0B /* mode register (w) */
-#define DMA1_CLEAR_FF_REG 0x0C /* clear pointer flip-flop (w) */
-#define DMA1_TEMP_REG 0x0D /* Temporary Register (r) */
-#define DMA1_RESET_REG 0x0D /* Master Clear (w) */
-#define DMA1_CLR_MASK_REG 0x0E /* Clear Mask */
-#define DMA1_MASK_ALL_REG 0x0F /* all-channels mask (w) */
-
-#define DMA2_CMD_REG 0xD0 /* command register (w) */
-#define DMA2_STAT_REG 0xD0 /* status register (r) */
-#define DMA2_REQ_REG 0xD2 /* request register (w) */
-#define DMA2_MASK_REG 0xD4 /* single-channel mask (w) */
-#define DMA2_MODE_REG 0xD6 /* mode register (w) */
-#define DMA2_CLEAR_FF_REG 0xD8 /* clear pointer flip-flop (w) */
-#define DMA2_TEMP_REG 0xDA /* Temporary Register (r) */
-#define DMA2_RESET_REG 0xDA /* Master Clear (w) */
-#define DMA2_CLR_MASK_REG 0xDC /* Clear Mask */
-#define DMA2_MASK_ALL_REG 0xDE /* all-channels mask (w) */
-
-#define DMA_ADDR_0 0x00 /* DMA address registers */
-#define DMA_ADDR_1 0x02
-#define DMA_ADDR_2 0x04
-#define DMA_ADDR_3 0x06
-#define DMA_ADDR_4 0xC0
-#define DMA_ADDR_5 0xC4
-#define DMA_ADDR_6 0xC8
-#define DMA_ADDR_7 0xCC
-
-#define DMA_CNT_0 0x01 /* DMA count registers */
-#define DMA_CNT_1 0x03
-#define DMA_CNT_2 0x05
-#define DMA_CNT_3 0x07
-#define DMA_CNT_4 0xC2
-#define DMA_CNT_5 0xC6
-#define DMA_CNT_6 0xCA
-#define DMA_CNT_7 0xCE
-
-#define DMA_PAGE_0 0x87 /* DMA page registers */
-#define DMA_PAGE_1 0x83
-#define DMA_PAGE_2 0x81
-#define DMA_PAGE_3 0x82
-#define DMA_PAGE_5 0x8B
-#define DMA_PAGE_6 0x89
-#define DMA_PAGE_7 0x8A
-
-#define DMA_MODE_READ 0x44 /* I/O to memory, no autoinit, increment, single mode */
-#define DMA_MODE_WRITE 0x48 /* memory to I/O, no autoinit, increment, single mode */
-#define DMA_MODE_CASCADE 0xC0 /* pass thru DREQ->HRQ, DACK<-HLDA only */
-
-#define DMA_AUTOINIT 0x10
-
-
-extern spinlock_t dma_spin_lock;
-
-static __inline__ unsigned long claim_dma_lock(void)
-{
- unsigned long flags;
- spin_lock_irqsave(&dma_spin_lock, flags);
- return flags;
-}
-
-static __inline__ void release_dma_lock(unsigned long flags)
-{
- spin_unlock_irqrestore(&dma_spin_lock, flags);
-}
-
-/* enable/disable a specific DMA channel */
-static __inline__ void enable_dma(unsigned int dmanr)
-{
- if (dmanr<=3)
- dma_outb(dmanr, DMA1_MASK_REG);
- else
- dma_outb(dmanr & 3, DMA2_MASK_REG);
-}
-
-static __inline__ void disable_dma(unsigned int dmanr)
-{
- if (dmanr<=3)
- dma_outb(dmanr | 4, DMA1_MASK_REG);
- else
- dma_outb((dmanr & 3) | 4, DMA2_MASK_REG);
-}
-
-/* Clear the 'DMA Pointer Flip Flop'.
- * Write 0 for LSB/MSB, 1 for MSB/LSB access.
- * Use this once to initialize the FF to a known state.
- * After that, keep track of it. :-)
- * --- In order to do that, the DMA routines below should ---
- * --- only be used while holding the DMA lock ! ---
- */
-static __inline__ void clear_dma_ff(unsigned int dmanr)
-{
- if (dmanr<=3)
- dma_outb(0, DMA1_CLEAR_FF_REG);
- else
- dma_outb(0, DMA2_CLEAR_FF_REG);
-}
-
-/* set mode (above) for a specific DMA channel */
-static __inline__ void set_dma_mode(unsigned int dmanr, char mode)
-{
- if (dmanr<=3)
- dma_outb(mode | dmanr, DMA1_MODE_REG);
- else
- dma_outb(mode | (dmanr&3), DMA2_MODE_REG);
-}
-
-/* Set only the page register bits of the transfer address.
- * This is used for successive transfers when we know the contents of
- * the lower 16 bits of the DMA current address register, but a 64k boundary
- * may have been crossed.
- */
-static __inline__ void set_dma_page(unsigned int dmanr, char pagenr)
-{
- switch(dmanr) {
- case 0:
- dma_outb(pagenr, DMA_PAGE_0);
- break;
- case 1:
- dma_outb(pagenr, DMA_PAGE_1);
- break;
- case 2:
- dma_outb(pagenr, DMA_PAGE_2);
- break;
- case 3:
- dma_outb(pagenr, DMA_PAGE_3);
- break;
- case 5:
- dma_outb(pagenr & 0xfe, DMA_PAGE_5);
- break;
- case 6:
- dma_outb(pagenr & 0xfe, DMA_PAGE_6);
- break;
- case 7:
- dma_outb(pagenr & 0xfe, DMA_PAGE_7);
- break;
- }
-}
-
-
-/* Set transfer address & page bits for specific DMA channel.
- * Assumes dma flipflop is clear.
- */
-static __inline__ void set_dma_addr(unsigned int dmanr, unsigned int a)
-{
- set_dma_page(dmanr, a>>16);
- if (dmanr <= 3) {
- dma_outb( a & 0xff, ((dmanr&3)<<1) + IO_DMA1_BASE );
- dma_outb( (a>>8) & 0xff, ((dmanr&3)<<1) + IO_DMA1_BASE );
- } else {
- dma_outb( (a>>1) & 0xff, ((dmanr&3)<<2) + IO_DMA2_BASE );
- dma_outb( (a>>9) & 0xff, ((dmanr&3)<<2) + IO_DMA2_BASE );
- }
-}
-
-
-/* Set transfer size (max 64k for DMA1..3, 128k for DMA5..7) for
- * a specific DMA channel.
- * You must ensure the parameters are valid.
- * NOTE: from a manual: "the number of transfers is one more
- * than the initial word count"! This is taken into account.
- * Assumes dma flip-flop is clear.
- * NOTE 2: "count" represents _bytes_ and must be even for channels 5-7.
- */
-static __inline__ void set_dma_count(unsigned int dmanr, unsigned int count)
-{
- count--;
- if (dmanr <= 3) {
- dma_outb( count & 0xff, ((dmanr&3)<<1) + 1 + IO_DMA1_BASE );
- dma_outb( (count>>8) & 0xff, ((dmanr&3)<<1) + 1 + IO_DMA1_BASE );
- } else {
- dma_outb( (count>>1) & 0xff, ((dmanr&3)<<2) + 2 + IO_DMA2_BASE );
- dma_outb( (count>>9) & 0xff, ((dmanr&3)<<2) + 2 + IO_DMA2_BASE );
- }
-}
-
-
-/* Get DMA residue count. After a DMA transfer, this
- * should return zero. Reading this while a DMA transfer is
- * still in progress will return unpredictable results.
- * If called before the channel has been used, it may return 1.
- * Otherwise, it returns the number of _bytes_ left to transfer.
- *
- * Assumes DMA flip-flop is clear.
- */
-static __inline__ int get_dma_residue(unsigned int dmanr)
-{
- unsigned int io_port = (dmanr<=3)? ((dmanr&3)<<1) + 1 + IO_DMA1_BASE
- : ((dmanr&3)<<2) + 2 + IO_DMA2_BASE;
-
- /* using short to get 16-bit wrap around */
- unsigned short count;
-
- count = 1 + dma_inb(io_port);
- count += dma_inb(io_port) << 8;
-
- return (dmanr<=3)? count : (count<<1);
-}
-
-
-/* These are in kernel/dma.c: */
-extern int request_dma(unsigned int dmanr, const char * device_id); /* reserve a DMA channel */
-extern void free_dma(unsigned int dmanr); /* release it again */
-
-/* From PCI */
-
-#ifdef CONFIG_PCI
-extern int isa_dma_bridge_buggy;
+#ifdef CONFIG_X86_PC9800
+#include <asm-i386/mach-pc9800/mach_dma.h>
#else
-#define isa_dma_bridge_buggy (0)
+#include <asm-i386/mach-default/mach_dma.h>
#endif

#endif /* _ASM_DMA_H */
diff -Nru linux/include/asm-i386/mach-default/mach_dma.h linux98/include/asm-i386/mach-default/mach_dma.h
--- linux/include/asm-i386/mach-default/mach_dma.h 1970-01-01 09:00:00.000000000 +0900
+++ linux98/include/asm-i386/mach-default/mach_dma.h 2003-03-17 15:28:32.000000000 +0900
@@ -0,0 +1,298 @@
+/* $Id: dma.h,v 1.7 1992/12/14 00:29:34 root Exp root $
+ * linux/include/asm/dma.h: Defines for using and allocating dma channels.
+ * Written by Hennus Bergman, 1992.
+ * High DMA channel support & info by Hannu Savolainen
+ * and John Boyd, Nov. 1992.
+ */
+
+#ifndef _ASM_MACH_DMA_H
+#define _ASM_MACH_DMA_H
+
+#include <linux/config.h>
+#include <linux/spinlock.h> /* And spinlocks */
+#include <asm/io.h> /* need byte IO */
+#include <linux/delay.h>
+
+
+#ifdef HAVE_REALLY_SLOW_DMA_CONTROLLER
+#define dma_outb outb_p
+#else
+#define dma_outb outb
+#endif
+
+#define dma_inb inb
+
+/*
+ * NOTES about DMA transfers:
+ *
+ * controller 1: channels 0-3, byte operations, ports 00-1F
+ * controller 2: channels 4-7, word operations, ports C0-DF
+ *
+ * - ALL registers are 8 bits only, regardless of transfer size
+ * - channel 4 is not used - cascades 1 into 2.
+ * - channels 0-3 are byte - addresses/counts are for physical bytes
+ * - channels 5-7 are word - addresses/counts are for physical words
+ * - transfers must not cross physical 64K (0-3) or 128K (5-7) boundaries
+ * - transfer count loaded to registers is 1 less than actual count
+ * - controller 2 offsets are all even (2x offsets for controller 1)
+ * - page registers for 5-7 don't use data bit 0, represent 128K pages
+ * - page registers for 0-3 use bit 0, represent 64K pages
+ *
+ * DMA transfers are limited to the lower 16MB of _physical_ memory.
+ * Note that addresses loaded into registers must be _physical_ addresses,
+ * not logical addresses (which may differ if paging is active).
+ *
+ * Address mapping for channels 0-3:
+ *
+ * A23 ... A16 A15 ... A8 A7 ... A0 (Physical addresses)
+ * | ... | | ... | | ... |
+ * | ... | | ... | | ... |
+ * | ... | | ... | | ... |
+ * P7 ... P0 A7 ... A0 A7 ... A0
+ * | Page | Addr MSB | Addr LSB | (DMA registers)
+ *
+ * Address mapping for channels 5-7:
+ *
+ * A23 ... A17 A16 A15 ... A9 A8 A7 ... A1 A0 (Physical addresses)
+ * | ... | \ \ ... \ \ \ ... \ \
+ * | ... | \ \ ... \ \ \ ... \ (not used)
+ * | ... | \ \ ... \ \ \ ... \
+ * P7 ... P1 (0) A7 A6 ... A0 A7 A6 ... A0
+ * | Page | Addr MSB | Addr LSB | (DMA registers)
+ *
+ * Again, channels 5-7 transfer _physical_ words (16 bits), so addresses
+ * and counts _must_ be word-aligned (the lowest address bit is _ignored_ at
+ * the hardware level, so odd-byte transfers aren't possible).
+ *
+ * Transfer count (_not # bytes_) is limited to 64K, represented as actual
+ * count - 1 : 64K => 0xFFFF, 1 => 0x0000. Thus, count is always 1 or more,
+ * and up to 128K bytes may be transferred on channels 5-7 in one operation.
+ *
+ */
+
+#define MAX_DMA_CHANNELS 8
+
+/* The maximum address that we can perform a DMA transfer to on this platform */
+#define MAX_DMA_ADDRESS (PAGE_OFFSET+0x1000000)
+
+/* 8237 DMA controllers */
+#define IO_DMA1_BASE 0x00 /* 8 bit slave DMA, channels 0..3 */
+#define IO_DMA2_BASE 0xC0 /* 16 bit master DMA, ch 4(=slave input)..7 */
+
+/* DMA controller registers */
+#define DMA1_CMD_REG 0x08 /* command register (w) */
+#define DMA1_STAT_REG 0x08 /* status register (r) */
+#define DMA1_REQ_REG 0x09 /* request register (w) */
+#define DMA1_MASK_REG 0x0A /* single-channel mask (w) */
+#define DMA1_MODE_REG 0x0B /* mode register (w) */
+#define DMA1_CLEAR_FF_REG 0x0C /* clear pointer flip-flop (w) */
+#define DMA1_TEMP_REG 0x0D /* Temporary Register (r) */
+#define DMA1_RESET_REG 0x0D /* Master Clear (w) */
+#define DMA1_CLR_MASK_REG 0x0E /* Clear Mask */
+#define DMA1_MASK_ALL_REG 0x0F /* all-channels mask (w) */
+
+#define DMA2_CMD_REG 0xD0 /* command register (w) */
+#define DMA2_STAT_REG 0xD0 /* status register (r) */
+#define DMA2_REQ_REG 0xD2 /* request register (w) */
+#define DMA2_MASK_REG 0xD4 /* single-channel mask (w) */
+#define DMA2_MODE_REG 0xD6 /* mode register (w) */
+#define DMA2_CLEAR_FF_REG 0xD8 /* clear pointer flip-flop (w) */
+#define DMA2_TEMP_REG 0xDA /* Temporary Register (r) */
+#define DMA2_RESET_REG 0xDA /* Master Clear (w) */
+#define DMA2_CLR_MASK_REG 0xDC /* Clear Mask */
+#define DMA2_MASK_ALL_REG 0xDE /* all-channels mask (w) */
+
+#define DMA_ADDR_0 0x00 /* DMA address registers */
+#define DMA_ADDR_1 0x02
+#define DMA_ADDR_2 0x04
+#define DMA_ADDR_3 0x06
+#define DMA_ADDR_4 0xC0
+#define DMA_ADDR_5 0xC4
+#define DMA_ADDR_6 0xC8
+#define DMA_ADDR_7 0xCC
+
+#define DMA_CNT_0 0x01 /* DMA count registers */
+#define DMA_CNT_1 0x03
+#define DMA_CNT_2 0x05
+#define DMA_CNT_3 0x07
+#define DMA_CNT_4 0xC2
+#define DMA_CNT_5 0xC6
+#define DMA_CNT_6 0xCA
+#define DMA_CNT_7 0xCE
+
+#define DMA_PAGE_0 0x87 /* DMA page registers */
+#define DMA_PAGE_1 0x83
+#define DMA_PAGE_2 0x81
+#define DMA_PAGE_3 0x82
+#define DMA_PAGE_5 0x8B
+#define DMA_PAGE_6 0x89
+#define DMA_PAGE_7 0x8A
+
+#define DMA_MODE_READ 0x44 /* I/O to memory, no autoinit, increment, single mode */
+#define DMA_MODE_WRITE 0x48 /* memory to I/O, no autoinit, increment, single mode */
+#define DMA_MODE_CASCADE 0xC0 /* pass thru DREQ->HRQ, DACK<-HLDA only */
+
+#define DMA_AUTOINIT 0x10
+
+
+extern spinlock_t dma_spin_lock;
+
+static __inline__ unsigned long claim_dma_lock(void)
+{
+ unsigned long flags;
+ spin_lock_irqsave(&dma_spin_lock, flags);
+ return flags;
+}
+
+static __inline__ void release_dma_lock(unsigned long flags)
+{
+ spin_unlock_irqrestore(&dma_spin_lock, flags);
+}
+
+/* enable/disable a specific DMA channel */
+static __inline__ void enable_dma(unsigned int dmanr)
+{
+ if (dmanr<=3)
+ dma_outb(dmanr, DMA1_MASK_REG);
+ else
+ dma_outb(dmanr & 3, DMA2_MASK_REG);
+}
+
+static __inline__ void disable_dma(unsigned int dmanr)
+{
+ if (dmanr<=3)
+ dma_outb(dmanr | 4, DMA1_MASK_REG);
+ else
+ dma_outb((dmanr & 3) | 4, DMA2_MASK_REG);
+}
+
+/* Clear the 'DMA Pointer Flip Flop'.
+ * Write 0 for LSB/MSB, 1 for MSB/LSB access.
+ * Use this once to initialize the FF to a known state.
+ * After that, keep track of it. :-)
+ * --- In order to do that, the DMA routines below should ---
+ * --- only be used while holding the DMA lock ! ---
+ */
+static __inline__ void clear_dma_ff(unsigned int dmanr)
+{
+ if (dmanr<=3)
+ dma_outb(0, DMA1_CLEAR_FF_REG);
+ else
+ dma_outb(0, DMA2_CLEAR_FF_REG);
+}
+
+/* set mode (above) for a specific DMA channel */
+static __inline__ void set_dma_mode(unsigned int dmanr, char mode)
+{
+ if (dmanr<=3)
+ dma_outb(mode | dmanr, DMA1_MODE_REG);
+ else
+ dma_outb(mode | (dmanr&3), DMA2_MODE_REG);
+}
+
+/* Set only the page register bits of the transfer address.
+ * This is used for successive transfers when we know the contents of
+ * the lower 16 bits of the DMA current address register, but a 64k boundary
+ * may have been crossed.
+ */
+static __inline__ void set_dma_page(unsigned int dmanr, char pagenr)
+{
+ switch(dmanr) {
+ case 0:
+ dma_outb(pagenr, DMA_PAGE_0);
+ break;
+ case 1:
+ dma_outb(pagenr, DMA_PAGE_1);
+ break;
+ case 2:
+ dma_outb(pagenr, DMA_PAGE_2);
+ break;
+ case 3:
+ dma_outb(pagenr, DMA_PAGE_3);
+ break;
+ case 5:
+ dma_outb(pagenr & 0xfe, DMA_PAGE_5);
+ break;
+ case 6:
+ dma_outb(pagenr & 0xfe, DMA_PAGE_6);
+ break;
+ case 7:
+ dma_outb(pagenr & 0xfe, DMA_PAGE_7);
+ break;
+ }
+}
+
+
+/* Set transfer address & page bits for specific DMA channel.
+ * Assumes dma flipflop is clear.
+ */
+static __inline__ void set_dma_addr(unsigned int dmanr, unsigned int a)
+{
+ set_dma_page(dmanr, a>>16);
+ if (dmanr <= 3) {
+ dma_outb( a & 0xff, ((dmanr&3)<<1) + IO_DMA1_BASE );
+ dma_outb( (a>>8) & 0xff, ((dmanr&3)<<1) + IO_DMA1_BASE );
+ } else {
+ dma_outb( (a>>1) & 0xff, ((dmanr&3)<<2) + IO_DMA2_BASE );
+ dma_outb( (a>>9) & 0xff, ((dmanr&3)<<2) + IO_DMA2_BASE );
+ }
+}
+
+
+/* Set transfer size (max 64k for DMA1..3, 128k for DMA5..7) for
+ * a specific DMA channel.
+ * You must ensure the parameters are valid.
+ * NOTE: from a manual: "the number of transfers is one more
+ * than the initial word count"! This is taken into account.
+ * Assumes dma flip-flop is clear.
+ * NOTE 2: "count" represents _bytes_ and must be even for channels 5-7.
+ */
+static __inline__ void set_dma_count(unsigned int dmanr, unsigned int count)
+{
+ count--;
+ if (dmanr <= 3) {
+ dma_outb( count & 0xff, ((dmanr&3)<<1) + 1 + IO_DMA1_BASE );
+ dma_outb( (count>>8) & 0xff, ((dmanr&3)<<1) + 1 + IO_DMA1_BASE );
+ } else {
+ dma_outb( (count>>1) & 0xff, ((dmanr&3)<<2) + 2 + IO_DMA2_BASE );
+ dma_outb( (count>>9) & 0xff, ((dmanr&3)<<2) + 2 + IO_DMA2_BASE );
+ }
+}
+
+
+/* Get DMA residue count. After a DMA transfer, this
+ * should return zero. Reading this while a DMA transfer is
+ * still in progress will return unpredictable results.
+ * If called before the channel has been used, it may return 1.
+ * Otherwise, it returns the number of _bytes_ left to transfer.
+ *
+ * Assumes DMA flip-flop is clear.
+ */
+static __inline__ int get_dma_residue(unsigned int dmanr)
+{
+ unsigned int io_port = (dmanr<=3)? ((dmanr&3)<<1) + 1 + IO_DMA1_BASE
+ : ((dmanr&3)<<2) + 2 + IO_DMA2_BASE;
+
+ /* using short to get 16-bit wrap around */
+ unsigned short count;
+
+ count = 1 + dma_inb(io_port);
+ count += dma_inb(io_port) << 8;
+
+ return (dmanr<=3)? count : (count<<1);
+}
+
+
+/* These are in kernel/dma.c: */
+extern int request_dma(unsigned int dmanr, const char * device_id); /* reserve a DMA channel */
+extern void free_dma(unsigned int dmanr); /* release it again */
+
+/* From PCI */
+
+#ifdef CONFIG_PCI
+extern int isa_dma_bridge_buggy;
+#else
+#define isa_dma_bridge_buggy (0)
+#endif
+
+#endif /* _ASM_MACH_DMA_H */
diff -Nru linux/include/asm-i386/mach-pc9800/mach_dma.h linux98/include/asm-i386/mach-pc9800/mach_dma.h
--- linux/include/asm-i386/mach-pc9800/mach_dma.h 1970-01-01 09:00:00.000000000 +0900
+++ linux98/include/asm-i386/mach-pc9800/mach_dma.h 2003-03-17 16:28:14.000000000 +0900
@@ -0,0 +1,258 @@
+/* $Id: dma.h,v 1.7 1992/12/14 00:29:34 root Exp root $
+ * linux/include/asm/dma.h: Defines for using and allocating dma channels.
+ * Written by Hennus Bergman, 1992.
+ * High DMA channel support & info by Hannu Savolainen
+ * and John Boyd, Nov. 1992.
+ *
+ * Modified for PC-9800 sub architecture by Osamu Tomita <tomita@cinet.co.jp>
+ */
+
+#ifndef _ASM_MACH_DMA_H
+#define _ASM_MACH_DMA_H
+
+#include <linux/config.h>
+#include <linux/spinlock.h> /* And spinlocks */
+#include <asm/io.h> /* need byte IO */
+#include <linux/delay.h>
+
+
+#ifdef HAVE_REALLY_SLOW_DMA_CONTROLLER
+#define dma_outb outb_p
+#else
+#define dma_outb outb
+#endif
+
+#define dma_inb inb
+
+/*
+ * NOTES about DMA transfers:
+ *
+ * controller 1: channels 0-3, byte operations, ports 01-1F
+ *
+ * - ALL registers are 8 bits only, regardless of transfer size
+ * - channels 0-3 are byte - addresses/counts are for physical bytes
+ * - transfers must not cross physical 64K (0-3) boundaries
+ * - transfer count loaded to registers is 1 less than actual count
+ * - page registers for 0-3 use bit 0, represent 64K pages
+ *
+ * Note that addresses loaded into registers must be _physical_ addresses,
+ * not logical addresses (which may differ if paging is active).
+ *
+ * Address mapping for channels 0-3:
+ *
+ * A31 ... A24 A23 ... A16 A15 ... A8 A7 ... A0 (Physical addresses)
+ * | ... | | ... | | ... | | ... |
+ * | ... | | ... | | ... | | ... |
+ * | ... | | ... | | ... | | ... |
+ * P7 ... P0 P7 ... P0 A7 ... A0 A7 ... A0
+ * | Ex Page | Page | Addr MSB | Addr LSB | (DMA registers)
+ *
+ * Transfer count (_not # bytes_) is limited to 64K, represented as actual
+ * count - 1 : 64K => 0xFFFF, 1 => 0x0000. Thus, count is always 1 or more.
+ *
+ */
+
+#define MAX_DMA_CHANNELS 4
+
+/* The maximum address that we can perform a DMA transfer to on this platform */
+#define MAX_DMA_ADDRESS (~0UL)
+
+/* 8237 DMA controllers */
+#define IO_DMA1_BASE 0x01 /* 8 bit DMA, channels 0..3 */
+#define IO_DMA2_BASE 0x00 /* none */
+
+/* DMA controller registers */
+#define DMA1_CMD_REG 0x11 /* command register (w) */
+#define DMA1_STAT_REG 0x11 /* status register (r) */
+#define DMA1_REQ_REG 0x13 /* request register (w) */
+#define DMA1_MASK_REG 0x15 /* single-channel mask (w) */
+#define DMA1_MODE_REG 0x17 /* mode register (w) */
+#define DMA1_CLEAR_FF_REG 0x19 /* clear pointer flip-flop (w) */
+#define DMA1_TEMP_REG 0x1B /* Temporary Register (r) */
+#define DMA1_RESET_REG 0x1B /* Master Clear (w) */
+#define DMA1_CLR_MASK_REG 0x1D /* Clear Mask */
+#define DMA1_MASK_ALL_REG 0x1F /* all-channels mask (w) */
+
+#define DMA2_CMD_REG 0x00 /* none */
+#define DMA2_STAT_REG 0x00 /* none */
+#define DMA2_REQ_REG 0x00 /* none */
+#define DMA2_MASK_REG 0x00 /* none */
+#define DMA2_MODE_REG 0x00 /* none */
+#define DMA2_CLEAR_FF_REG 0x00 /* none */
+#define DMA2_TEMP_REG 0x00 /* none */
+#define DMA2_RESET_REG 0x00 /* none */
+#define DMA2_CLR_MASK_REG 0x00 /* none */
+#define DMA2_MASK_ALL_REG 0x00 /* none */
+
+#define DMA_ADDR_0 0x01 /* DMA address registers */
+#define DMA_ADDR_1 0x05
+#define DMA_ADDR_2 0x09
+#define DMA_ADDR_3 0x0D
+#define DMA_ADDR_4 0x00 /* none */
+#define DMA_ADDR_5 0x00 /* none */
+#define DMA_ADDR_6 0x00 /* none */
+#define DMA_ADDR_7 0x00 /* none */
+
+#define DMA_CNT_0 0x03 /* DMA count registers */
+#define DMA_CNT_1 0x07
+#define DMA_CNT_2 0x0B
+#define DMA_CNT_3 0x0F
+#define DMA_CNT_4 0x00 /* none */
+#define DMA_CNT_5 0x00 /* none */
+#define DMA_CNT_6 0x00 /* none */
+#define DMA_CNT_7 0x00 /* none */
+
+#define DMA_PAGE_0 0x27 /* DMA page registers */
+#define DMA_PAGE_1 0x21
+#define DMA_PAGE_2 0x23
+#define DMA_PAGE_3 0x25
+#define DMA_PAGE_5 0x00 /* none */
+#define DMA_PAGE_6 0x00 /* none */
+#define DMA_PAGE_7 0x00 /* none */
+
+#define DMA_Ex_PAGE_0 0xe05 /* DMA Extended page reg base */
+#define DMA_Ex_PAGE_1 0xe07
+#define DMA_Ex_PAGE_2 0xe09
+#define DMA_Ex_PAGE_3 0xe0b
+
+#define DMA_MODE_READ 0x44 /* I/O to memory, no autoinit, increment, single mode */
+#define DMA_MODE_WRITE 0x48 /* memory to I/O, no autoinit, increment, single mode */
+#define DMA_MODE_CASCADE 0x00 /* none */
+
+#define DMA_AUTOINIT 0x10
+
+
+extern spinlock_t dma_spin_lock;
+
+static __inline__ unsigned long claim_dma_lock(void)
+{
+ unsigned long flags;
+ spin_lock_irqsave(&dma_spin_lock, flags);
+ return flags;
+}
+
+static __inline__ void release_dma_lock(unsigned long flags)
+{
+ spin_unlock_irqrestore(&dma_spin_lock, flags);
+}
+
+/* enable/disable a specific DMA channel */
+static __inline__ void enable_dma(unsigned int dmanr)
+{
+ dma_outb(dmanr, DMA1_MASK_REG);
+}
+
+static __inline__ void disable_dma(unsigned int dmanr)
+{
+ dma_outb(dmanr | 4, DMA1_MASK_REG);
+}
+
+/* Clear the 'DMA Pointer Flip Flop'.
+ * Write 0 for LSB/MSB, 1 for MSB/LSB access.
+ * Use this once to initialize the FF to a known state.
+ * After that, keep track of it. :-)
+ * --- In order to do that, the DMA routines below should ---
+ * --- only be used while holding the DMA lock ! ---
+ */
+static __inline__ void clear_dma_ff(unsigned int dmanr)
+{
+ dma_outb(0, DMA1_CLEAR_FF_REG);
+}
+
+/* set mode (above) for a specific DMA channel */
+static __inline__ void set_dma_mode(unsigned int dmanr, char mode)
+{
+ dma_outb(mode | dmanr, DMA1_MODE_REG);
+}
+
+/* Set only the page register bits of the transfer address.
+ * This is used for successive transfers when we know the contents of
+ * the lower 16 bits of the DMA current address register, but a 64k boundary
+ * may have been crossed.
+ */
+static __inline__ void set_dma_page(unsigned int dmanr, unsigned int pagenr)
+{
+ unsigned char low=pagenr&0xff;
+ unsigned char hi=pagenr>>8;
+
+ switch(dmanr) {
+ case 0:
+ dma_outb(low, DMA_PAGE_0);
+ dma_outb(hi, DMA_Ex_PAGE_0);
+ break;
+ case 1:
+ dma_outb(low, DMA_PAGE_1);
+ dma_outb(hi, DMA_Ex_PAGE_1);
+ break;
+ case 2:
+ dma_outb(low, DMA_PAGE_2);
+ dma_outb(hi, DMA_Ex_PAGE_2);
+ break;
+ case 3:
+ dma_outb(low, DMA_PAGE_3);
+ dma_outb(hi, DMA_Ex_PAGE_3);
+ break;
+ }
+}
+
+
+/* Set transfer address & page bits for specific DMA channel.
+ * Assumes dma flipflop is clear.
+ */
+static __inline__ void set_dma_addr(unsigned int dmanr, unsigned int a)
+{
+ set_dma_page(dmanr, a>>16);
+ dma_outb( a & 0xff, ((dmanr&3)<<2) + IO_DMA1_BASE );
+ dma_outb( (a>>8) & 0xff, ((dmanr&3)<<2) + IO_DMA1_BASE );
+}
+
+
+/* Set transfer size (max 64k for DMA1..3, 128k for DMA5..7) for
+ * a specific DMA channel.
+ * You must ensure the parameters are valid.
+ * NOTE: from a manual: "the number of transfers is one more
+ * than the initial word count"! This is taken into account.
+ * Assumes dma flip-flop is clear.
+ * NOTE 2: "count" represents _bytes_ and must be even for channels 5-7.
+ */
+static __inline__ void set_dma_count(unsigned int dmanr, unsigned int count)
+{
+ count--;
+ dma_outb( count & 0xff, ((dmanr&3)<<2) + 2 + IO_DMA1_BASE );
+ dma_outb( (count>>8) & 0xff, ((dmanr&3)<<2) + 2 + IO_DMA1_BASE );
+}
+
+
+/* Get DMA residue count. After a DMA transfer, this
+ * should return zero. Reading this while a DMA transfer is
+ * still in progress will return unpredictable results.
+ * If called before the channel has been used, it may return 1.
+ * Otherwise, it returns the number of _bytes_ left to transfer.
+ *
+ * Assumes DMA flip-flop is clear.
+ */
+static __inline__ int get_dma_residue(unsigned int dmanr)
+{
+ /* using short to get 16-bit wrap around */
+ unsigned short count;
+
+ count = 1 + dma_inb(((dmanr&3)<<2) + 2 + IO_DMA1_BASE);
+ count += dma_inb(((dmanr&3)<<2) + 2 + IO_DMA1_BASE) << 8;
+
+ return count;
+}
+
+
+/* These are in kernel/dma.c: */
+extern int request_dma(unsigned int dmanr, const char * device_id); /* reserve a DMA channel */
+extern void free_dma(unsigned int dmanr); /* release it again */
+
+/* From PCI */
+
+#ifdef CONFIG_PCI
+extern int isa_dma_bridge_buggy;
+#else
+#define isa_dma_bridge_buggy (0)
+#endif
+
+#endif /* _ASM_MACH_DMA_H */
diff -Nru linux/include/asm-i386/scatterlist.h linux98/include/asm-i386/scatterlist.h
--- linux/include/asm-i386/scatterlist.h 2002-04-15 04:18:52.000000000 +0900
+++ linux98/include/asm-i386/scatterlist.h 2002-04-17 10:37:22.000000000 +0900
@@ -1,6 +1,8 @@
#ifndef _I386_SCATTERLIST_H
#define _I386_SCATTERLIST_H

+#include <linux/config.h>
+
struct scatterlist {
struct page *page;
unsigned int offset;
@@ -8,6 +10,10 @@
unsigned int length;
};

+#ifdef CONFIG_X86_PC9800
+#define ISA_DMA_THRESHOLD (0xffffffff)
+#else
#define ISA_DMA_THRESHOLD (0x00ffffff)
+#endif

#endif /* !(_I386_SCATTERLIST_H) */
diff -Nru linux/kernel/dma.c linux98/kernel/dma.c
--- linux/kernel/dma.c 2002-08-11 10:41:22.000000000 +0900
+++ linux98/kernel/dma.c 2002-08-21 09:53:59.000000000 +0900
@@ -9,6 +9,7 @@
* [It also happened to remove the sizeof(char *) == sizeof(int)
* assumption introduced because of those /proc/dma patches. -- Hennus]
*/
+#include <linux/config.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/errno.h>
@@ -62,10 +63,12 @@
{ 0, 0 },
{ 0, 0 },
{ 0, 0 },
+#ifndef CONFIG_X86_PC9800
{ 1, "cascade" },
{ 0, 0 },
{ 0, 0 },
{ 0, 0 }
+#endif
};


-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
\
 
 \ /
  Last update: 2005-03-22 13:34    [from the cache]
©2003-2011 Jasper Spaans. Advertise on this site