Messages in this thread |  | | | Subject | Re: 2.5.65-mm1 | | From | Alexander Hoogerhuis <> | | Date | 19 Mar 2003 01:14:13 +0100 |
| |
Russell King <rmk@arm.linux.org.uk> writes:
> On Tue, Mar 18, 2003 at 04:51:11PM +0100, Alexander Hoogerhuis wrote: > > Oh well, I've had one hang within 10 minutes of booting, came back and > > the machine was unresponsive (mouse and keyboard under X, unable to > > switch to console). Apart from that I've got two funnies in my boot > > messages: > > Could you send the full bus information for all devices (lspci -vv), > and the contents of /proc/iomem and /proc/ioports ? > > I don't believe there's anything in my PCI updates which should have > changed the behaviour - they were touching mainly the scanning for > devices, and the way we write resources back into the hardware. The > latter rarely happens on x86, except for cardbus devices. >
I'm not suspecting the PCI in particular for the PCIC-bits, only making X and the Radeon work again. But here you are:
lapper root # lspci -vv 00:00.0 Host bridge: Intel Corp. 82845 845 (Brookdale) Chipset Host Bridge (rev 04) Subsystem: Compaq Computer Corporation: Unknown device 004a Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 0 Region 0: Memory at a0000000 (32-bit, prefetchable) [size=256M] Capabilities: [e4] #09 [d104] Capabilities: [a0] AGP version 2.0 Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2,x4 Command: RQ=0 SBA+ AGP+ 64bit- FW- Rate=x4 00:01.0 PCI bridge: Intel Corp. 82845 845 (Brookdale) Chipset AGP Bridge (rev 04) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 00003000-00003fff Memory behind bridge: 80300000-803fffff Prefetchable memory behind bridge: 88000000-900fffff BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B- 00:1e.0 PCI bridge: Intel Corp. 82801BAM/CAM PCI Bridge (rev 42) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=02, subordinate=03, sec-latency=32 I/O behind bridge: 00002000-00002fff Memory behind bridge: 80000000-803fffff BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- 00:1f.0 ISA bridge: Intel Corp. 82801CAM ISA Bridge (LPC) (rev 02) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0
00:1f.1 IDE interface: Intel Corp. 82801CAM IDE U100 (rev 02) (prog-if 8a [Master SecP PriP]) Subsystem: Compaq Computer Corporation: Unknown device 004a Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 5 Region 0: I/O ports at <unassigned> Region 1: I/O ports at <unassigned> Region 2: I/O ports at <unassigned> Region 3: I/O ports at <unassigned> Region 4: I/O ports at 4440 [size=16] Region 5: Memory at 30000400 (32-bit, non-prefetchable) [size=1K] 00:1f.5 Multimedia audio controller: Intel Corp. 82801CA/CAM AC'97 Audio (rev 02) Subsystem: Compaq Computer Corporation: Unknown device 004a Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin B routed to IRQ 5 Region 0: I/O ports at 4000 [size=256] Region 1: I/O ports at 4400 [size=64]
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M7 LW [Radeon Mobility 7500] (prog-if 00 [VGA]) Subsystem: Compaq Computer Corporation: Unknown device 004a Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 66 (2000ns min), cache line size 08 Interrupt: pin A routed to IRQ 11 Region 0: Memory at 88000000 (32-bit, prefetchable) [size=128M] Region 1: I/O ports at 3000 [size=256] Region 2: Memory at 80380000 (32-bit, non-prefetchable) [size=64K] Expansion ROM at <unassigned> [disabled] [size=128K] Capabilities: [58] AGP version 2.0 Status: RQ=47 SBA+ 64bit- FW- Rate=x1,x2,x4 Command: RQ=31 SBA+ AGP+ 64bit- FW- Rate=x4 Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 02:04.0 Communication controller: Lucent Microelectronics LT WinModem (rev 02) Subsystem: AMBIT Microsystem Corp.: Unknown device 0450 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 66 (63000ns min, 3500ns max) Interrupt: pin A routed to IRQ 5 Region 0: Memory at 80280000 (32-bit, non-prefetchable) [size=256] Region 1: I/O ports at 2440 [size=8] Region 2: I/O ports at 2000 [size=256] Capabilities: [f8] Power Management version 2 Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=160mA PME(D0-,D1-,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 02:06.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus Controller (rev 02) Subsystem: Compaq Computer Corporation: Unknown device 004a Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 168, cache line size 20 Interrupt: pin A routed to IRQ 11 Region 0: Memory at 80080000 (32-bit, non-prefetchable) [size=4K] Bus: primary=02, secondary=03, subordinate=06, sec-latency=176 Memory window 0: 30400000-307ff000 (prefetchable) Memory window 1: 30800000-30bff000 I/O window 0: 00001400-000014ff I/O window 1: 00001800-000018ff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+ 16-bit legacy interface ports at 0001 02:08.0 Ethernet controller: Intel Corp. 82801CAM (ICH3) PRO/100 VE (LOM) Ethernet Controller (rev 42) Subsystem: Compaq Computer Corporation: Unknown device 0093 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 66 (2000ns min, 14000ns max), cache line size 08 Interrupt: pin A routed to IRQ 10 Region 0: Memory at 80100000 (32-bit, non-prefetchable) [size=4K] Region 1: I/O ports at 2400 [size=64] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=2 PME- 02:0e.0 USB Controller: NEC Corporation USB (rev 41) (prog-if 10 [OHCI]) Subsystem: Compaq Computer Corporation: Unknown device 004a Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (250ns min, 10500ns max), cache line size 08 Interrupt: pin A routed to IRQ 10 Region 0: Memory at 80180000 (32-bit, non-prefetchable) [size=4K] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 02:0e.1 USB Controller: NEC Corporation USB (rev 41) (prog-if 10 [OHCI]) Subsystem: Compaq Computer Corporation: Unknown device 004a Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (250ns min, 10500ns max), cache line size 08 Interrupt: pin B routed to IRQ 10 Region 0: Memory at 80200000 (32-bit, non-prefetchable) [size=4K] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 02:0e.2 USB Controller: NEC Corporation USB 2.0 (rev 02) (prog-if 20 [EHCI]) Subsystem: Compaq Computer Corporation: Unknown device 004a Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (4000ns min, 8500ns max), cache line size 20 Interrupt: pin C routed to IRQ 10 Region 0: Memory at 30000000 (32-bit, non-prefetchable) [size=256] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- lapper root # cat /proc/iomem /proc/ioports 00000000-0009fbff : System RAM 0009fc00-0009ffff : reserved 000a0000-000bffff : Video RAM area 000c0000-000c7fff : Video ROM 000f0000-000fffff : System ROM 00100000-2ffcffff : System RAM 00100000-002af453 : Kernel code 002af454-00364003 : Kernel data 2ffd0000-2fff0bff : reserved 2fff0c00-2fffbfff : ACPI Non-volatile Storage 2fffc000-2fffffff : reserved 30000000-300000ff : NEC Corporation USB 2.0 30000000-300000ff : ehci-hcd 30000400-300007ff : Intel Corp. 82801CAM IDE U100 30400000-307fffff : PCI CardBus #03 30800000-30bfffff : PCI CardBus #03 80080000-80080fff : Texas Instruments PCI1410 PC card Card 80100000-80100fff : Intel Corp. 82801CAM (ICH3) PRO/ 80100000-80100fff : eepro100 80180000-80180fff : NEC Corporation USB 80180000-80180fff : ohci-hcd 80200000-80200fff : NEC Corporation USB (#2) 80200000-80200fff : ohci-hcd 80280000-802800ff : Lucent Microelectron LT WinModem 80300000-803fffff : PCI Bus #01 80380000-8038ffff : ATI Technologies Inc Radeon Mobility M7 L 88000000-900fffff : PCI Bus #01 88000000-8fffffff : ATI Technologies Inc Radeon Mobility M7 L a0000000-afffffff : Intel Corp. 82845 845 (Brookdale 0000-001f : dma1 0020-003f : pic1 0040-005f : timer 0060-006f : keyboard 0080-008f : dma page reg 00a0-00bf : pic2 00c0-00df : dma2 00f0-00ff : fpu 0170-0177 : ide1 01f0-01f7 : ide0 0376-0376 : ide1 0378-037a : parport0 037b-037f : parport0 03c0-03df : vga+ 03f6-03f6 : ide0 0cf8-0cff : PCI conf1 1060-106f : i810 TCO 1400-14ff : PCI CardBus #03 1800-18ff : PCI CardBus #03 2000-20ff : Lucent Microelectron LT WinModem 2400-243f : Intel Corp. 82801CAM (ICH3) PRO/ 2400-243f : eepro100 2440-2447 : Lucent Microelectron LT WinModem 3000-3fff : PCI Bus #01 3000-30ff : ATI Technologies Inc Radeon Mobility M7 L 4000-40ff : Intel Corp. 82801CA/CAM AC'97 Au 4000-40ff : Intel ICH3 4400-443f : Intel Corp. 82801CA/CAM AC'97 Au 4400-443f : Intel ICH3 4440-444f : Intel Corp. 82801CAM IDE U100 4440-4447 : ide0 4448-444f : ide1 lapper root # mvh, A -- Alexander Hoogerhuis | alexh@ihatent.com CCNP - CCDP - MCNE - CCSE | +47 908 21 485 "You have zero privacy anyway. Get over it." --Scott McNealy - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
|  |