lkml.org 
[lkml]   [2003]   [Dec]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectE7505 has only 2 APIC's but Linux says 3
Hi,

According to Intel's spec. for the E7505 chipset, there are only two
APICs mapped at 0xFEC00000 and 0xFEC80000.

On boot, however, both kernel's 2.4 and 2.6 report three APIC's (see
dmesg snippet below). That third memory address (oxFEC80100) looks odd
to me.

Could the MPTable be incorrect thus leading Linux astray or could it be
a kernel problem?

Could my system's APIC's end up being mis-configured/mis-used as a result?

Many thanks,

Dan.

Output from dmesg:

Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: Product ID: PLACER CRB APIC at: 0xFEE00000
I/O APIC #2 Version 32 at 0xFEC00000.
I/O APIC #3 Version 32 at 0xFEC80000.
I/O APIC #4 Version 32 at 0xFEC80100.
Enabling APIC mode: Flat. Using 3 I/O APICs

Output from lspci:

00:00.0 Host bridge: Intel Corp. E7505 Memory Controller Hub (rev 03)
Subsystem: Tyan Computer: Unknown device 2665
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Capabilities: [40] #09 [0104]
Capabilities: [a0] AGP version 3.0
Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2
Command: RQ=0 SBA- AGP+ 64bit- FW- Rate=x2

00:00.1 Class ff00: Intel Corp. E7000 Series RAS Controller (rev 03)
Subsystem: Tyan Computer: Unknown device 2665
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

00:01.0 PCI bridge: Intel Corp. E7000 Series Processor to AGP Controller
(rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M]
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: d9000000-d9ffffff
Prefetchable memory behind bridge: f0000000-f7ffffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [60] AGP version 3.5
Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2
Command: RQ=0 SBA+ AGP+ 64bit- FW- Rate=x2

00:02.0 PCI bridge: Intel Corp. E7000 Series Hub Interface B PCI-to-PCI
Bridge (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Bus: primary=00, secondary=02, subordinate=04, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: da000000-da1fffff
Prefetchable memory behind bridge: fff00000-000fffff
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-

00:1d.0 USB Controller: Intel Corp. 82801DB USB (Hub #1) (rev 02)
(prog-if 00 [UHCI])
Subsystem: Tyan Computer: Unknown device 2665
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 4: I/O ports at 1840 [size=32]

00:1d.1 USB Controller: Intel Corp. 82801DB USB (Hub #2) (rev 02)
(prog-if 00 [UHCI])
Subsystem: Tyan Computer: Unknown device 2665
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 10
Region 4: I/O ports at 1860 [size=32]

00:1d.2 USB Controller: Intel Corp. 82801DB USB (Hub #3) (rev 02)
(prog-if 00 [UHCI])
Subsystem: Tyan Computer: Unknown device 2665
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 5
Region 4: I/O ports at 1880 [size=32]

00:1d.7 USB Controller: Intel Corp. 82801DB USB2 (rev 02) (prog-if 20
[EHCI])
Subsystem: Tyan Computer: Unknown device 2665
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 11
Region 0: Memory at d8000000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] #0a [2080]

00:1e.0 PCI bridge: Intel Corp. 82801BA/CA/DB/EB PCI Bridge (rev 82)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=32
I/O behind bridge: 00003000-00003fff
Memory behind bridge: da200000-da2fffff
Prefetchable memory behind bridge: fff00000-000fffff
BridgeCtl: Parity+ SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-

00:1f.0 ISA bridge: Intel Corp. 82801DB LPC Interface Controller (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0

00:1f.1 IDE interface: Intel Corp. 82801DB Ultra ATA Storage Controller
(rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Tyan Computer: Unknown device 2665
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 0
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at 18a0 [size=16]
Region 5: Memory at 80000000 (32-bit, non-prefetchable) [size=1K]

00:1f.3 SMBus: Intel Corp. 82801DB/DBM SMBus Controller (rev 02)
Subsystem: Tyan Computer: Unknown device 2665
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 0
Region 4: I/O ports at 1100 [size=32]

00:1f.5 Multimedia audio controller: Intel Corp. 82801DB AC'97 Audio
Controller (rev 02)
Subsystem: Tyan Computer: Unknown device 2665
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 3
Region 0: I/O ports at 1400 [size=256]
Region 1: I/O ports at 1800 [size=64]
Region 2: Memory at d8000c00 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at d8000800 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

01:00.0 VGA compatible controller: nVidia Corporation NV34 [GeForce FX
5200] (rev a1) (prog-if 00 [VGA])
Subsystem: Asustek Computer, Inc.: Unknown device 80df
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 248 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 3
Region 0: Memory at d9000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at f0000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 3.0
Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2
Command: RQ=31 SBA- AGP+ 64bit- FW- Rate=x2

02:1c.0 PIC: Intel Corp. 82870P2 P64H2 I/OxAPIC (rev 04) (prog-if 20
[IO(X)-APIC])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at da000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [50] PCI-X non-bridge device.
Command: DPERE- ERO- RBC=0 OST=0
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-,
DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
02:1d.0 PCI bridge: Intel Corp. 82870P2 P64H2 Hub PCI Bridge (rev 04)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 248, cache line size 20
Bus: primary=02, secondary=03, subordinate=03, sec-latency=64
I/O behind bridge: 00002000-00002fff
Memory behind bridge: da100000-da1fffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] PCI-X non-bridge device.
Command: DPERE+ ERO+ RBC=0 OST=0
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-,
DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
02:1e.0 PIC: Intel Corp. 82870P2 P64H2 I/OxAPIC (rev 04) (prog-if 20
[IO(X)-APIC])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at da001000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [50] PCI-X non-bridge device.
Command: DPERE- ERO- RBC=0 OST=0
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-,
DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
02:1f.0 PCI bridge: Intel Corp. 82870P2 P64H2 Hub PCI Bridge (rev 04)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 248, cache line size 20
Bus: primary=02, secondary=04, subordinate=04, sec-latency=64
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] PCI-X non-bridge device.
Command: DPERE+ ERO+ RBC=0 OST=4
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-,
DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
03:03.0 SCSI storage controller: LSI Logic / Symbios Logic 53c1030 PCI-X
Fusion-MPT Dual Ultra320 SCSI (rev 07)
Subsystem: LSI Logic / Symbios Logic: Unknown device 1040
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 136 (4250ns min, 4500ns max), cache line size 08
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at 2000 [size=256]
Region 1: Memory at da110000 (64-bit, non-prefetchable) [size=64K]
Region 3: Memory at da100000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at <unassigned> [disabled] [size=1M]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Message Signalled Interrupts: 64bit+
Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [68] PCI-X non-bridge device.
Command: DPERE- ERO- RBC=2 OST=0
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-,
DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
03:03.1 SCSI storage controller: LSI Logic / Symbios Logic 53c1030 PCI-X
Fusion-MPT Dual Ultra320 SCSI (rev 07)
Subsystem: LSI Logic / Symbios Logic: Unknown device 1040
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 136 (4250ns min, 4500ns max), cache line size 08
Interrupt: pin B routed to IRQ 5
Region 0: I/O ports at 2400 [size=256]
Region 1: Memory at da130000 (64-bit, non-prefetchable) [size=64K]
Region 3: Memory at da120000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at <unassigned> [disabled] [size=1M]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Message Signalled Interrupts: 64bit+
Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [68] PCI-X non-bridge device.
Command: DPERE- ERO- RBC=2 OST=0
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-,
DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
05:02.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A
IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI])
Subsystem: Tyan Computer: Unknown device 2665
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 1000ns max), cache line size 08
Interrupt: pin A routed to IRQ 3
Region 0: Memory at da204000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at da200000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

05:03.0 Ethernet controller: Intel Corp. 82540EM Gigabit Ethernet
Controller (rev 02)
Subsystem: Tyan Computer: Unknown device 2665
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 252 (63750ns min), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at da220000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 3000 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [e4] PCI-X non-bridge device.
Command: DPERE- ERO+ RBC=2 OST=0
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-,
DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM- Capabilities: [f0]
Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000

--
dan@dcrdev.demon.co.uk
www.dancres.org



-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2005-03-22 13:59    [W:0.052 / U:0.532 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site