lkml.org 
[lkml]   [2003]   [Nov]   [4]   [last100]   RSS Feed
Views: [more markup]  [less markup]  [headers]  [forward] 
 
Messages in this thread
/
FromErno Rigo <>
SubjectRe: kernel: ata1: DMA timeout, stat 0x1
DateTue, 4 Nov 2003 14:01:33 +0100
On Tuesday 04 November 2003 13:51, Erno Rigo wrote:

Hmm... Additional information...

libata version 0.75 loaded.
sata_via version 0.11
PCI: Found IRQ 3 for device 0000:00:0f.0
IRQ routing conflict for 0000:00:0f.0, have irq 9, want irq 3
PCI: Sharing IRQ 3 with 0000:00:0f.1
IRQ routing conflict for 0000:00:10.0, have irq 9, want irq 3
IRQ routing conflict for 0000:00:10.1, have irq 9, want irq 3
ata1: SATA max UDMA/133 cmd 0xD000 ctl 0xB802 bmdma 0xA800 irq 9
ata2: SATA max UDMA/133 cmd 0xB400 ctl 0xB002 bmdma 0xA808 irq 9
ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003 
88:407f
ata1: dev 0 ATA, max UDMA/133, 234441648 sectors (lba48)
ata1: dev 0 configured for UDMA/133
scsi0 : sata_via
ATA: abnormal status 0x7F on port 0xB407
ata2: thread exiting
scsi1 : sata_via
  Vendor: ATA       Model: ST3120026AS       Rev: 0.75
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
SCSI device sda: drive cache: write through
 /dev/scsi/host0/bus0/target0/lun0: p1
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0,  type 0

> Hello!
>
> [1.] One line summary of the problem:
>
> kernel: ata1: DMA timeout, stat 0x1
>
> [2.] Full description of the problem/report:
>
> I've just purchased a VIA KT600 based mainboard and a Seagate Barracuda
> 120G SATA drive. The controller and the drive is properly recognized, but
> after a while, independent of the workload, I get the above error, and the
> drive bails out. (It's unaccessible from the point I get the message).
>
> I've also tried the backport in 2.4.22-ac4, it's a bit more verbose, and
> complains about a 'scsi Media Sense error' before the dma timeout.
>
> [3.] Keywords (i.e., modules, networking, kernel):
>
> VIA, SATA
>
> [4.] Kernel version (from /proc/version):
>
> Linux version 2.6.0-test9 (root@mcree) (gcc version 3.3.2 20030908 (Debian
> prerelease)) #6 Tue Nov 4 13:11:19 CET 2003
>
> [5.] Output of Oops.. message (if applicable) with symbolic information
>      resolved (see Documentation/oops-tracing.txt)
>
> N/A
>
> [6.] A small shell script or example program which triggers the
>      problem (if possible)
>
> Normal usage. (Sometimes I can cp tens of gigabytes, sometimes I can't even
> change to a directory)
>
> [7.] Environment
> [7.1.] Software (add the output of the ver_linux script here)
>
> Linux mcree 2.6.0-test9 #6 Tue Nov 4 13:11:19 CET 2003 i686 GNU/Linux
>
> Gnu C                  3.3.2
> Gnu make               3.80
> util-linux             2.12
> mount                  2.12
> module-init-tools      0.9.15-pre2
> e2fsprogs              1.35-WIP
> Linux C Library        2.3.2
> Dynamic linker (ldd)   2.3.2
> Procps                 3.1.12
> Net-tools              1.60
> Console-tools          0.2.3
> Sh-utils               5.0.90
> Modules Loaded
>
> [7.2.] Processor information (from /proc/cpuinfo):
>
> processor       : 0
> vendor_id       : AuthenticAMD
> cpu family      : 6
> model           : 8
> model name      : AMD Athlon(TM) XP 2100+
> stepping        : 1
> cpu MHz         : 1734.223
> cache size      : 256 KB
> fdiv_bug        : no
> hlt_bug         : no
> f00f_bug        : no
> coma_bug        : no
> fpu             : yes
> fpu_exception   : yes
> cpuid level     : 1
> wp              : yes
> flags           : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca
> cmov pat pse36 mmx fxsr sse syscall mmxext 3dnowext 3dnow
> bogomips        : 3416.06
>
> [7.3.] Module information (from /proc/modules):
>
> empty
>
> [7.4.] Loaded driver and hardware information (/proc/ioports, /proc/iomem)
>
> [root@mcree| /usr/src/linux-2.6.0-test9/scripts]#cat /proc/ioports
> 0000-001f : dma1
> 0020-0021 : pic1
> 0040-005f : timer
> 0060-006f : keyboard
> 0070-0077 : rtc
> 0080-008f : dma page reg
> 00a0-00a1 : pic2
> 00c0-00df : dma2
> 00f0-00ff : fpu
> 0170-0177 : ide1
> 01f0-01f7 : ide0
> 0376-0376 : ide1
> 0378-037a : parport0
> 03c0-03df : vga+
> 03f6-03f6 : ide0
> 03f8-03ff : serial
> 0cf8-0cff : PCI conf1
> 8400-84ff : 0000:00:13.0
>   8400-84ff : tulip
> 8800-881f : 0000:00:10.3
> 9000-901f : 0000:00:10.2
> 9400-941f : 0000:00:10.1
> 9800-981f : 0000:00:10.0
> a000-a00f : 0000:00:0f.1
>   a000-a007 : ide0
>   a008-a00f : ide1
> a400-a4ff : 0000:00:0f.0
>   a400-a4ff : libata
> a800-a80f : 0000:00:0f.0
>   a800-a80f : libata
> b000-b003 : 0000:00:0f.0
>   b000-b003 : libata
> b400-b407 : 0000:00:0f.0
>   b400-b407 : libata
> b800-b803 : 0000:00:0f.0
>   b800-b803 : libata
> d000-d007 : 0000:00:0f.0
>   d000-d007 : libata
> d400-d43f : 0000:00:0e.0
> d800-d8ff : 0000:00:09.0
>
> [root@mcree| /usr/src/linux-2.6.0-test9/scripts]#cat /proc/iomem
> 00000000-0009d7ff : System RAM
> 0009d800-0009ffff : reserved
> 000a0000-000bffff : Video RAM area
> 000c0000-000c7fff : Video ROM
> 000f0000-000fffff : System ROM
> 00100000-1fffbfff : System RAM
>   00100000-0034aa64 : Kernel code
>   0034aa65-004195ff : Kernel data
> 1fffc000-1fffefff : ACPI Tables
> 1ffff000-1fffffff : ACPI Non-volatile Storage
> ea800000-ea8003ff : 0000:00:13.0
>   ea800000-ea8003ff : tulip
> eb000000-eb0000ff : 0000:00:10.4
> eb800000-eb803fff : 0000:00:09.0
> ec000000-edefffff : PCI Bus #01
>   ec000000-ecffffff : 0000:01:00.0
> ee000000-ee000fff : 0000:00:0d.1
> ee800000-ee800fff : 0000:00:0d.0
>   ee800000-ee800fff : bttv0
> ef700000-f7ffffff : PCI Bus #01
>   ef800000-ef87ffff : 0000:01:00.0
>   f0000000-f7ffffff : 0000:01:00.0
> f8000000-fbffffff : 0000:00:00.0
> fec00000-fec00fff : reserved
> fee00000-fee00fff : reserved
> ffff0000-ffffffff : reserved
>
> [7.5.] PCI information ('lspci -vvv' as root)
>
> [root@mcree| /usr/src/linux-2.6.0-test9/scripts]#lspci -vvv
> 00:00.0 Host bridge: VIA Technologies, Inc. VT8377 [KT400 AGP] Host Bridge
> (rev 80)
>         Subsystem: Asustek Computer, Inc.: Unknown device 807f
>         Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
>         Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort+ >SERR- <PERR-
>         Latency: 0
>         Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
>         Capabilities: [80] AGP version 3.5
>                 Status: RQ=32 Iso- ArqSz=0 Cal=2 SBA+ ITACoh- GART64-
> HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
>                 Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-
> Rate=<none>
>         Capabilities: [c0] Power Management version 2
>                 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:01.0 PCI bridge: VIA Technologies, Inc.: Unknown device b198 (prog-if 00
> [Normal decode])
>         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
>         Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort+ >SERR- <PERR-
>         Latency: 0
>         Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
>         I/O behind bridge: 0000e000-0000dfff
>         Memory behind bridge: ec000000-edefffff
>         Prefetchable memory behind bridge: ef700000-f7ffffff
>         BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
>         Capabilities: [80] Power Management version 2
>                 Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:09.0 Ethernet controller: 3Com Corporation: Unknown device 1700 (rev 12)
>         Subsystem: Asustek Computer, Inc.: Unknown device 80eb
>         Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
>         Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
>         Latency: 32 (5750ns min, 7750ns max), cache line size 08
>         Interrupt: pin A routed to IRQ 5
>         Region 0: Memory at eb800000 (32-bit, non-prefetchable) [disabled]
> [size=16K]
>         Region 1: I/O ports at d800 [disabled] [size=256]
>         Capabilities: [48] Power Management version 2
>                 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2
> +,D3hot+,D3cold+)
>                 Status: D0 PME-Enable- DSel=7 DScale=1 PME-
>         Capabilities: [50] Vital Product Data
>
> 00:0d.0 Multimedia video controller: Brooktree Corporation Bt878 Video
> Capture (rev 11)
>         Subsystem: Pinnacle Systems Inc. PCTV pro (TV + FM stereo receiver)
>         Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
>         Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
>         Latency: 32 (4000ns min, 10000ns max)
>         Interrupt: pin A routed to IRQ 11
>         Region 0: Memory at ee800000 (32-bit, prefetchable) [size=4K]
>         Capabilities: [44] Vital Product Data
>         Capabilities: [4c] Power Management version 2
>                 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:0d.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture
> (rev 11)
>         Subsystem: Pinnacle Systems Inc. PCTV pro (TV + FM stereo receiver,
> audio section)
>         Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
>         Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
>         Latency: 32 (1000ns min, 63750ns max)
>         Interrupt: pin A routed to IRQ 11
>         Region 0: Memory at ee000000 (32-bit, prefetchable) [disabled]
> [size=4K]
>         Capabilities: [44] Vital Product Data
>         Capabilities: [4c] Power Management version 2
>                 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:0e.0 Multimedia audio controller: Ensoniq 5880 AudioPCI (rev 02)
>         Subsystem: Ensoniq Creative Sound Blaster AudioPCI128
>         Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
>         Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
>         Latency: 32 (3000ns min, 32000ns max)
>         Interrupt: pin A routed to IRQ 0
>         Region 0: I/O ports at d400 [disabled] [size=64]
>         Capabilities: [dc] Power Management version 1
>                 Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:0f.0 RAID bus controller: VIA Technologies, Inc.: Unknown device 3149
> (rev 80)
>         Subsystem: Asustek Computer, Inc.: Unknown device 80ed
>         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
>         Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
>         Latency: 32
>         Interrupt: pin A routed to IRQ 9
>         Region 0: I/O ports at d000 [size=8]
>         Region 1: I/O ports at b800 [size=4]
>         Region 2: I/O ports at b400 [size=8]
>         Region 3: I/O ports at b000 [size=4]
>         Region 4: I/O ports at a800 [size=16]
>         Region 5: I/O ports at a400 [size=256]
>         Capabilities: [c0] Power Management version 2
>                 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586/B/686A/B PIPC Bus
> Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
>         Subsystem: Asustek Computer, Inc.: Unknown device 80ed
>         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
>         Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
>         Latency: 32
>         Interrupt: pin A routed to IRQ 3
>         Region 4: I/O ports at a000 [size=16]
>         Capabilities: [c0] Power Management version 2
>                 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:10.0 USB Controller: VIA Technologies, Inc. USB (rev 81) (prog-if 00
> [UHCI])
>         Subsystem: Asustek Computer, Inc.: Unknown device 80ed
>         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
>         Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
>         Latency: 32, cache line size 08
>         Interrupt: pin A routed to IRQ 9
>         Region 4: I/O ports at 9800 [size=32]
>         Capabilities: [80] Power Management version 2
>                 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2
> +,D3hot+,D3cold+)
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:10.1 USB Controller: VIA Technologies, Inc. USB (rev 81) (prog-if 00
> [UHCI])
>         Subsystem: Asustek Computer, Inc.: Unknown device 80ed
>         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
>         Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
>         Latency: 32, cache line size 08
>         Interrupt: pin A routed to IRQ 9
>         Region 4: I/O ports at 9400 [size=32]
>         Capabilities: [80] Power Management version 2
>                 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2
> +,D3hot+,D3cold+)
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:10.2 USB Controller: VIA Technologies, Inc. USB (rev 81) (prog-if 00
> [UHCI])
>         Subsystem: Asustek Computer, Inc.: Unknown device 80ed
>         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
>         Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
>         Latency: 32, cache line size 08
>         Interrupt: pin B routed to IRQ 11
>         Region 4: I/O ports at 9000 [size=32]
>         Capabilities: [80] Power Management version 2
>                 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2
> +,D3hot+,D3cold+)
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:10.3 USB Controller: VIA Technologies, Inc. USB (rev 81) (prog-if 00
> [UHCI])
>         Subsystem: Asustek Computer, Inc.: Unknown device 80ed
>         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
>         Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
>         Latency: 32, cache line size 08
>         Interrupt: pin B routed to IRQ 11
>         Region 4: I/O ports at 8800 [size=32]
>         Capabilities: [80] Power Management version 2
>                 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2
> +,D3hot+,D3cold+)
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86) (prog-if 20
> [EHCI])
>         Subsystem: Asustek Computer, Inc.: Unknown device 80ed
>         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
>         Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
>         Latency: 32, cache line size 08
>         Interrupt: pin C routed to IRQ 10
>         Region 0: Memory at eb000000 (32-bit, non-prefetchable) [size=256]
>         Capabilities: [80] Power Management version 2
>                 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2
> +,D3hot+,D3cold+)
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:11.0 ISA bridge: VIA Technologies, Inc.: Unknown device 3227
>         Subsystem: Asustek Computer, Inc.: Unknown device 80ed
>         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping+ SERR- FastB2B-
>         Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
>         Latency: 0
>         Capabilities: [c0] Power Management version 2
>                 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:13.0 Ethernet controller: Accton Technology Corporation EN-1216 Ethernet
> Adapter (rev 11)
>         Subsystem: Standard Microsystems Corp [SMC]: Unknown device 1255
>         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
>         Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
>         Latency: 32 (63750ns min, 63750ns max), cache line size 08
>         Interrupt: pin A routed to IRQ 5
>         Region 0: I/O ports at 8400 [size=256]
>         Region 1: Memory at ea800000 (32-bit, non-prefetchable) [size=1K]
>         Expansion ROM at <unassigned> [disabled] [size=128K]
>         Capabilities: [c0] Power Management version 2
>                 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=100mA PME(D0+,D1+,D2
> +,D3hot+,D3cold+)
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 01:00.0 VGA compatible controller: nVidia Corporation NV17 [GeForce4 MX
> 440] (rev a3) (prog-if 00 [VGA])
>         Subsystem: ABIT Computer Corp. Abit Siluro GeForce4MX440
>         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
>         Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
>         Latency: 64 (1250ns min, 250ns max)
>         Interrupt: pin A routed to IRQ 11
>         Region 0: Memory at ec000000 (32-bit, non-prefetchable) [size=16M]
>         Region 1: Memory at f0000000 (32-bit, prefetchable) [size=128M]
>         Region 2: Memory at ef800000 (32-bit, prefetchable) [size=512K]
>         Expansion ROM at ef7e0000 [disabled] [size=128K]
>         Capabilities: [60] Power Management version 2
>                 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>         Capabilities: [44] AGP version 2.0
>                 Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64-
> HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
>                 Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-
> Rate=<none>
>
> [7.6.] SCSI information (from /proc/scsi/scsi)
>
> [root@mcree| /usr/src/linux-2.6.0-test9/scripts]#cat /proc/scsi/scsi
> Attached devices:
> Host: scsi0 Channel: 00 Id: 00 Lun: 00
>   Vendor: ATA      Model: ST3120026AS      Rev: 0.75
>   Type:   Direct-Access                    ANSI SCSI revision: 05
>
>
> [7.7.] Other information that might be relevant to the problem
>        (please look in /proc and include all information that you
>        think to be relevant):
>
> [root@mcree| /usr/src/linux-2.6.0-test9/scripts]#hdparm
> /dev/scsi/host0/bus0/ target0/lun0/disc
>
> /dev/scsi/host0/bus0/target0/lun0/disc:
>  readonly     =  0 (off)
>
> (Hangs here in kernel mode - unable to kill -9 it)
>
> [X.] Other notes, patches, fixes, workarounds:
>
> Please CC your additional questions to mcree@freemail.hu, as I'm not on the
> kernel mailing list.

-- 
McRee
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2005-03-22 13:58    [from the cache]
©2003-2008