lkml.org 
[lkml]   [2003]   [Nov]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    Date
    From
    SubjectRe: OOps! was: 2.6.0-test9-mm5
    On Mon, Nov 24, 2003 at 06:41:58PM -0500, Zwane Mwaikambo wrote:
    > On Mon, 24 Nov 2003, Mike Fedyk wrote:
    >
    > > I'm getting an oops on boot, right after serial is initialised.
    > >
    > > Two things it says:
    > > BAD EIP!
    > > Trying to kill init!
    > >
    > > Yes, I'm using preempt. I'll try without, and see if that "fixes" the
    > > problem, and try some other versions, since the last 2.6 booted on this
    > > machine is 2.6.0-test6-mm4.
    >
    > Any chance you can capture the oops in it's entirety? It might also be
    > worth booting with the 'initcall_debug' kernel parameter.

    I just compiled witout preempt and it still gives an oops at the same spot.

    It doesn't give a trace. Will it still be helpful for you, and the eip was
    something like 00095

    Here is a boot from my most recent previous kernel:

    Linux version 2.6.0-test6-mm4 (root@srv-lr2600) (gcc version 3.3.2 20030908 (Debian prerelease)) #2 SMP Mon Oct 6 02:32:09 PDT 2003
    Video mode to be used for restore is f01
    BIOS-provided physical RAM map:
    BIOS-e820: 0000000000000000 - 000000000009e400 (usable)
    BIOS-e820: 000000000009e400 - 00000000000a0000 (reserved)
    BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
    BIOS-e820: 0000000000100000 - 000000005fffc000 (usable)
    BIOS-e820: 000000005fffc000 - 000000005ffff000 (ACPI data)
    BIOS-e820: 000000005ffff000 - 0000000060000000 (ACPI NVS)
    BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
    BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
    BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
    639MB HIGHMEM available.
    896MB LOWMEM available.
    On node 0 totalpages: 393212
    DMA zone: 4096 pages, LIFO batch:1
    Normal zone: 225280 pages, LIFO batch:16
    HighMem zone: 163836 pages, LIFO batch:16
    DMI 2.3 present.
    ACPI: RSDP (v000 ASUS ) @ 0x000f5dc0
    ACPI: RSDT (v001 ASUS A7V8X-X 0x42302e31 MSFT 0x31313031) @ 0x5fffc000
    ACPI: FADT (v001 ASUS A7V8X-X 0x42302e31 MSFT 0x31313031) @ 0x5fffc0b2
    ACPI: BOOT (v001 ASUS A7V8X-X 0x42302e31 MSFT 0x31313031) @ 0x5fffc030
    ACPI: MADT (v001 ASUS A7V8X-X 0x42302e31 MSFT 0x31313031) @ 0x5fffc058
    ACPI: DSDT (v001 ASUS A7V8X-X 0x00001000 MSFT 0x0100000b) @ 0x00000000
    ACPI: Local APIC address 0xfee00000
    ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
    Processor #0 6:8 APIC version 16
    ACPI: LAPIC_NMI (acpi_id[0x00] polarity[0x1] trigger[0x1] lint[0x1])
    ACPI: IOAPIC (id[0x02] address[0xfec00000] global_irq_base[0x0])
    IOAPIC[0]: Assigned apic_id 2
    IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, IRQ 0-23
    ACPI: INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x0] trigger[0x1])
    ACPI: INT_SRC_OVR (bus[0] irq[0x9] global_irq[0x9] polarity[0x3] trigger[0x3])
    Enabling APIC mode: Flat. Using 1 I/O APICs
    Using ACPI (MADT) for SMP configuration information
    Building zonelist for node : 0
    Kernel command line: root=/dev/hda1 ro vga=extended nmi_watchdog=2 ide=reverse
    ide_setup: ide=reverse : Enabled support for IDE inverse scan order.
    Initializing CPU#0
    PID hash table entries: 4096 (order 12: 32768 bytes)
    Detected 2083.203 MHz processor.
    Console: colour VGA+ 80x50
    Memory: 1552416k/1572848k available (2270k kernel code, 19280k reserved, 884k data, 192k init, 655344k highmem)
    Calibrating delay loop... 4104.19 BogoMIPS
    Security Scaffold v1.0.0 initialized
    Capability LSM initialized
    Dentry cache hash table entries: 262144 (order: 8, 1048576 bytes)
    Inode-cache hash table entries: 131072 (order: 7, 524288 bytes)
    Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
    CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000
    CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000
    CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
    CPU: L2 Cache: 256K (64 bytes/line)
    CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000020
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#0.
    Enabling fast FPU save and restore... done.
    Enabling unmasked SIMD FPU exception support... done.
    Checking 'hlt' instruction... OK.
    POSIX conformance testing by UNIFIX
    CPU0: AMD Athlon(TM) XP 2600+ stepping 01
    per-CPU timeslice cutoff: 731.36 usecs.
    task migration cache decay timeout: 1 msecs.
    enabled ExtINT on CPU#0
    ESR value before enabling vector: 00000000
    ESR value after enabling vector: 00000000
    Error: only one processor found.
    ENABLING IO-APIC IRQs
    init IO_APIC IRQs
    IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not connected.
    ..TIMER: vector=0x31 pin1=2 pin2=-1
    number of MP IRQ sources: 15.
    number of IO-APIC #2 registers: 24.
    testing the IO APIC.......................
    IO APIC #2......
    .... register #00: 02000000
    ....... : physical APIC id: 02
    ....... : Delivery Type: 0
    ....... : LTS : 0
    .... register #01: 00178003
    ....... : max redirection entries: 0017
    ....... : PRQ implemented: 1
    ....... : IO APIC version: 0003
    .... IRQ redirection table:
    NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
    00 000 00 1 0 0 0 0 0 0 00
    01 001 01 0 0 0 0 0 1 1 39
    02 001 01 0 0 0 0 0 1 1 31
    03 001 01 0 0 0 0 0 1 1 41
    04 001 01 0 0 0 0 0 1 1 49
    05 001 01 0 0 0 0 0 1 1 51
    06 001 01 0 0 0 0 0 1 1 59
    07 001 01 0 0 0 0 0 1 1 61
    08 001 01 0 0 0 0 0 1 1 69
    09 001 01 1 1 0 1 0 1 1 71
    0a 001 01 0 0 0 0 0 1 1 79
    0b 001 01 0 0 0 0 0 1 1 81
    0c 001 01 0 0 0 0 0 1 1 89
    0d 001 01 0 0 0 0 0 1 1 91
    0e 001 01 0 0 0 0 0 1 1 99
    0f 001 01 0 0 0 0 0 1 1 A1
    10 000 00 1 0 0 0 0 0 0 00
    11 000 00 1 0 0 0 0 0 0 00
    12 000 00 1 0 0 0 0 0 0 00
    13 000 00 1 0 0 0 0 0 0 00
    14 000 00 1 0 0 0 0 0 0 00
    15 000 00 1 0 0 0 0 0 0 00
    16 000 00 1 0 0 0 0 0 0 00
    17 000 00 1 0 0 0 0 0 0 00
    IRQ to pin mappings:
    IRQ0 -> 0:2
    IRQ1 -> 0:1
    IRQ3 -> 0:3
    IRQ4 -> 0:4
    IRQ5 -> 0:5
    IRQ6 -> 0:6
    IRQ7 -> 0:7
    IRQ8 -> 0:8
    IRQ9 -> 0:9
    IRQ10 -> 0:10
    IRQ11 -> 0:11
    IRQ12 -> 0:12
    IRQ13 -> 0:13
    IRQ14 -> 0:14
    IRQ15 -> 0:15
    .................................... done.
    Using local APIC timer interrupts.
    calibrating APIC timer ...
    ..... CPU clock speed is 2082.0719 MHz.
    ..... host bus clock speed is 333.0235 MHz.
    Starting migration thread for cpu 0
    CPUS done 2
    NET: Registered protocol family 16
    PCI: PCI BIOS revision 2.10 entry at 0xf15e0, last bus=1
    PCI: Using configuration type 1
    mtrr: v2.0 (20020519)
    ACPI: Subsystem revision 20030813
    ACPI: Interpreter enabled
    ACPI: Using IOAPIC for interrupt routing
    ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11 12 14 15, disabled)
    ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
    ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11 12 14)
    ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15, disabled)
    ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15, enabled at IRQ 9)
    ACPI: PCI Root Bridge [PCI0] (00:00)
    PCI: Probing PCI hardware (bus 00)
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
    Linux Plug and Play Support v0.97 (c) Adam Belay
    PnPBIOS: Scanning system for PnP BIOS support...
    PnPBIOS: Found PnP BIOS installation structure at 0xc00f9bf0
    PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x9c20, dseg 0xf0000
    PnPBIOS: 14 nodes reported by PnP BIOS; 14 recorded by driver
    SCSI subsystem initialized
    IOAPIC[0]: Set PCI routing entry (2-17 -> 0xa9 -> IRQ 17 Mode:1 Active:1)
    00:00:07[A] -> 2-17 -> IRQ 17
    Pin 2-17 already programmed
    IOAPIC[0]: Set PCI routing entry (2-18 -> 0xb1 -> IRQ 18 Mode:1 Active:1)
    00:00:09[A] -> 2-18 -> IRQ 18
    IOAPIC[0]: Set PCI routing entry (2-19 -> 0xb9 -> IRQ 19 Mode:1 Active:1)
    00:00:0c[A] -> 2-19 -> IRQ 19
    IOAPIC[0]: Set PCI routing entry (2-16 -> 0xc1 -> IRQ 16 Mode:1 Active:1)
    00:00:0c[B] -> 2-16 -> IRQ 16
    Pin 2-17 already programmed
    Pin 2-18 already programmed
    Pin 2-16 already programmed
    Pin 2-17 already programmed
    Pin 2-18 already programmed
    Pin 2-19 already programmed
    Pin 2-17 already programmed
    Pin 2-18 already programmed
    Pin 2-19 already programmed
    Pin 2-16 already programmed
    Pin 2-18 already programmed
    Pin 2-19 already programmed
    Pin 2-16 already programmed
    Pin 2-17 already programmed
    Pin 2-19 already programmed
    Pin 2-16 already programmed
    Pin 2-17 already programmed
    Pin 2-18 already programmed
    Pin 2-16 already programmed
    Pin 2-17 already programmed
    Pin 2-18 already programmed
    Pin 2-19 already programmed
    IOAPIC[0]: Set PCI routing entry (2-21 -> 0xc9 -> IRQ 21 Mode:1 Active:1)
    00:00:10[A] -> 2-21 -> IRQ 21
    Pin 2-21 already programmed
    sage repeated 2 times
    IOAPIC[0]: Set PCI routing entry (2-22 -> 0xd1 -> IRQ 22 Mode:1 Active:1)
    00:00:11[C] -> 2-22 -> IRQ 22
    IOAPIC[0]: Set PCI routing entry (2-23 -> 0xd9 -> IRQ 23 Mode:1 Active:1)
    00:00:12[A] -> 2-23 -> IRQ 23
    Pin 2-16 already programmed
    Pin 2-17 already programmed
    ACPI: No IRQ known for interrupt pin A of device 0000:00:11.1 - using IRQ 255
    PCI: Using ACPI for IRQ routing
    PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
    divert: not allocating divert_blk for non-ethernet device lo
    SBF: Simple Boot Flag extension found and enabled.
    SBF: Setting boot flags 0x1
    Machine check exception polling timer started.
    apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
    apm: overridden by ACPI.
    highmem bounce pool size: 64 pages
    VFS: Disk quotas dquot_6.5.1
    Initializing Cryptographic API
    ACPI: Power Button (FF) [PWRF]
    ACPI: Processor [CPU0] (supports C1)
    isapnp: Scanning for PnP cards...
    isapnp: No Plug & Play device found
    pty: 256 Unix98 ptys configured
    Hangcheck: starting hangcheck timer 0.5.0 (tick is 180 seconds, margin is 60 seconds).
    Serial: 8250/16550 driver $Revision: 1.90 $ IRQ sharing enabled


    It oopses here.


    ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
    ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    VP_IDE: IDE controller at PCI slot 0000:00:11.1
    ACPI: No IRQ known for interrupt pin A of device 0000:00:11.1 - using IRQ 255
    VP_IDE: chipset revision 6
    VP_IDE: not 100%% native mode: will probe irqs later
    VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
    ide0: BM-DMA at 0x8400-0x8407, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0x8408-0x840f, BIOS settings: hdc:pio, hdd:pio
    hda: IBM-DPTA-372730, ATA DISK drive
    Using anticipatory io scheduler
    ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
    SiI680: IDE controller at PCI slot 0000:00:0e.0
    SiI680: chipset revision 2
    SiI680: BASE CLOCK == 133
    SiI680: 100%% native mode on irq 17
    ide2: MMIO-DMA at 0xf880a000-0xf880a007, BIOS settings: hde:pio, hdf:pio
    ide3: MMIO-DMA at 0xf880a008-0xf880a00f, BIOS settings: hdg:pio, hdh:pio
    hde: Maxtor 6Y160P0, ATA DISK drive
    ide2 at 0xf880a080-0xf880a087,0xf880a08a on irq 17
    hdg: Maxtor 6Y160P0, ATA DISK drive
    ide3 at 0xf880a0c0-0xf880a0c7,0xf880a0ca on irq 17
    PDC20269: IDE controller at PCI slot 0000:00:0c.0
    PDC20269: chipset revision 2
    PDC20269: 100%% native mode on irq 19
    ide4: BM-DMA at 0xb400-0xb407, BIOS settings: hdi:pio, hdj:pio
    ide5: BM-DMA at 0xb408-0xb40f, BIOS settings: hdk:pio, hdl:pio
    hdi: Maxtor 6Y160P0, ATA DISK drive
    ide4 at 0xd800-0xd807,0xd402 on irq 19
    hdk: Maxtor 6Y160P0, ATA DISK drive
    ide5 at 0xd000-0xd007,0xb802 on irq 19
    hda: max request size: 128KiB
    hda: 53464320 sectors (27373 MB) w/1961KiB Cache, CHS=53040/16/63, UDMA(66)
    hda: hda1 hda2
    hde: max request size: 64KiB
    hde: 320173056 sectors (163928 MB) w/7936KiB Cache, CHS=19929/255/63, UDMA(133)
    hde: hde1 hde2 hde3
    hdg: max request size: 64KiB
    hdg: 320173056 sectors (163928 MB) w/7936KiB Cache, CHS=19929/255/63, UDMA(133)
    hdg: hdg1 hdg2
    hdi: max request size: 1024KiB
    hdi: 320173056 sectors (163928 MB) w/7936KiB Cache, CHS=19929/255/63, UDMA(133)
    hdi: hdi1 hdi3
    hdk: max request size: 1024KiB
    hdk: 320173056 sectors (163928 MB) w/7936KiB Cache, CHS=19929/255/63, UDMA(133)
    hdk: hdk1 hdk2 hdk3
    mice: PS/2 mouse device common for all mice
    serio: i8042 AUX port at 0x60,0x64 irq 12
    input: AT Translated Set 2 keyboard on isa0060/serio0
    serio: i8042 KBD port at 0x60,0x64 irq 1
    md: linear personality registered as nr 1
    md: raid0 personality registered as nr 2
    md: raid1 personality registered as nr 3
    md: raid5 personality registered as nr 4
    raid5: measuring checksumming speed
    8regs : 3148.000 MB/sec
    8regs_prefetch: 2768.000 MB/sec
    32regs : 1996.000 MB/sec
    32regs_prefetch: 1748.000 MB/sec
    pIII_sse : 1704.000 MB/sec
    pII_mmx : 5548.000 MB/sec
    p5_mmx : 7372.000 MB/sec
    raid5: using function: pIII_sse (1704.000 MB/sec)
    md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
    device-mapper: 4.0.0-ioctl (2003-06-04) initialised: dm@uk.sistina.com
    NET: Registered protocol family 2
    IP: routing cache hash table of 8192 buckets, 128Kbytes
    TCP: Hash tables configured (established 262144 bind 43690)
    BIOS EDD facility v0.09 2003-Jan-22, 5 devices found
    md: Autodetecting RAID arrays.
    md: autorun ...
    md: considering hdk3 ...
    md: adding hdk3 ...
    md: hdk1 has different UUID to hdk3
    md: adding hdi3 ...
    md: adding hde3 ...
    md: hde1 has different UUID to hdk3
    md: created md0
    md: bind<hde3>
    md: bind<hdi3>
    md: bind<hdk3>
    md: running: <hdk3><hdi3><hde3>
    raid5: device hdk3 operational as raid disk 2
    raid5: device hdi3 operational as raid disk 1
    raid5: device hde3 operational as raid disk 0
    raid5: allocated 3148kB for md0
    raid5: raid level 5 set md0 active with 3 out of 3 devices, algorithm 0
    RAID5 conf printout:
    --- rd:3 wd:3 fd:0
    disk 0, o:1, dev:hde3
    disk 1, o:1, dev:hdi3
    disk 2, o:1, dev:hdk3
    md: considering hdk1 ...
    md: adding hdk1 ...
    md: adding hde1 ...
    md: created md1
    md: bind<hde1>
    md: bind<hdk1>
    md: running: <hdk1><hde1>
    raid1: raid set md1 active with 2 out of 2 mirrors
    md: ... autorun DONE.
    kjournald starting. Commit interval 5 seconds
    EXT3-fs: mounted filesystem with ordered data mode.
    VFS: Mounted root (ext3 filesystem) readonly.
    Freeing unused kernel memory: 192k freed
    NET: Registered protocol family 1
    Adding 364888k swap on /dev/hda2. Priority:1 extents:1
    EXT3 FS on hda1, internal journal
    Real Time Clock Driver v1.12
    8139too Fast Ethernet driver 0.9.26
    via-rhine.c:v1.10-LK1.1.19-2.5 July-12-2003 Written by Donald Becker
    http://www.scyld.com/network/via-rhine.html
    divert: allocating divert_blk for eth0
    eth0: VIA VT6102 Rhine-II at 0xf7000000, 00:0c:6e:1f:81:95, IRQ 23.
    eth0: MII PHY found at address 1, status 0x786d advertising 01e1 Link 45e1.
    inserting floppy driver for 2.6.0-test6-mm4
    Floppy drive(s): fd0 is 1.44M
    FDC 0 is a post-1991 82077
    end_request: I/O error, dev fd0, sector 0
    Adding 262136k swap on /usr/swap_file. Priority:2 extents:68
    parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
    parport0: irq 7 detected
    parport0: cpp_daisy: aa5500ff(38)
    parport0: assign_addrs: aa5500ff(38)
    parport0: cpp_daisy: aa5500ff(38)
    parport0: assign_addrs: aa5500ff(38)
    lp0: using parport0 (polling).
    drivers/usb/core/usb.c: registered new driver usbfs
    drivers/usb/core/usb.c: registered new driver hub
    ehci_hcd 0000:00:10.3: EHCI Host Controller
    ehci_hcd 0000:00:10.3: irq 21, pci mem f8875000
    ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 1
    ehci_hcd 0000:00:10.3: USB 2.0 enabled, EHCI 1.00, driver 2003-Jun-13
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 6 ports detected
    ohci-hcd: 2003 Feb 24 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
    ohci-hcd: block sizes: ed 64 td 64
    drivers/usb/host/uhci-hcd.c: USB Universal Host Controller Interface driver v2.1
    uhci-hcd 0000:00:10.0: UHCI Host Controller
    uhci-hcd 0000:00:10.0: irq 21, io base 00009400
    uhci-hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 2 ports detected
    uhci-hcd 0000:00:10.1: UHCI Host Controller
    uhci-hcd 0000:00:10.1: irq 21, io base 00009000
    uhci-hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
    hub 3-0:1.0: USB hub found
    hub 3-0:1.0: 2 ports detected
    uhci-hcd 0000:00:10.2: UHCI Host Controller
    uhci-hcd 0000:00:10.2: irq 21, io base 00008800
    uhci-hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
    hub 4-0:1.0: USB hub found
    hub 4-0:1.0: 2 ports detected
    hub 2-0:1.0: new USB device on port 2, assigned address 2
    eth0: Setting full-duplex based on MII #1 link partner capability of 45e1.
    nfs warning: mount version older than kernel
    sage repeated 3 times
    ttyS1: LSR safety check engaged!
    ttyS1: LSR safety check engaged!
    process `named' is using obsolete setsockopt SO_BSDCOMPAT
    sage repeated 5 times
    input: Logitech USB Mouse on usb-0000:00:10.0-2
    drivers/usb/core/usb.c: registered new driver usbmouse
    drivers/usb/input/usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
    drivers/usb/core/usb.c: registered new driver hiddev
    drivers/usb/core/usb.c: registered new driver hid
    drivers/usb/input/hid-core.c: v2.0:USB HID core driver
    nfs: server fs not responding, still trying
    sage repeated 2 times
    nfs: server fs OK
    sage repeated 2 times
    nfs: server fs not responding, still trying
    sage repeated 3 times
    nfs: server fs OK
    sage repeated 3 times
    nfs: server fs not responding, still trying
    nfs: server fs not responding, still trying
    nfs: server fs OK
    nfs: server fs OK
    process `rndc' is using obsolete setsockopt SO_BSDCOMPAT
    Kernel logging (proc) stopped.
    Kernel log daemon terminating.
    -
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

    \
     
     \ /
      Last update: 2005-03-22 13:58    [W:0.051 / U:0.404 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site