Messages in this thread | | | From | age <> | Subject | READAHEAD | Date | Thu, 30 Oct 2003 20:23:06 +0100 |
| |
Hi, Andre
Hi,
I have a problem which i don`t understand and i hope that you will and can help me. The problem is that i experience strange disk read performance. I have to set hdparm -m16 -u1 -c1 -d1 -a4096 /dev/hde to get timing buffered disk reads of 56 MB/SEC. When i disable readahead i get 17 MB/SEC When i enable readahead with -a8 i get 17 MB/SEC When i enable readahead with -a16 i get 24,5 MB/SEC When i enable readahead with -a32 i get 30,5 MB/SEC When i enable readahead with -a64 i get 35 MB/SEC When i enable readahead with -a128 i get 39 MB/SEC When i enable readahead with -a256 i get 39 MB/SEC When i enable readahead with -a512 i get 41 MB/SEC When i enable readahead with -a1024 i get 50 MB/SEC When i enable readahead with -a2048 i get 50 MB/SEC When i enable readahead with -a4096 i get 56 MB/SEC With -a8192,-a16384 and -a32768 i get also 56MB/SEC
Before, i never had to set readahead so high Please could you tell me, what is going on here ?
I use 2.6.0-test9 with TCQ enabled. The harddisk is the new Hitachi 7K250 40 GB PATA.
PS: It doesn`t matter when i disable tcq and/or multcount, i get the same results.
THX
Age huisman
/dev/hde:
Model=HDS722540VLAT20, FwRev=V31OA60A, SerialNo=VN321EC2R9X1ML Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs } RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=52 BuffType=DualPortCache, BuffSize=1794kB, MaxMultSect=16, MultSect=16 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=80418240 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120} PIO modes: pio0 pio1 pio2 pio3 pio4 DMA modes: mdma0 mdma1 mdma2 UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5 AdvancedPM=yes: disabled (255) WriteCache=enabled Drive conforms to: ATA/ATAPI-6 T13 1410D revision 3a:
* signifies the current active mode
ATA device, with non-removable media powers-up in standby; SET FEATURES subcmd spins-up. Model Number: HDS722540VLAT20 Serial Number: VN321EC2R9X1ML Firmware Revision: V31OA60A Standards: Used: ATA/ATAPI-6 T13 1410D revision 3a Supported: 6 5 4 3 Configuration: Logical max current cylinders 16383 65535 heads 16 1 sectors/track 63 63 -- CHS current addressable sectors: 4128705 LBA user addressable sectors: 80418240 LBA48 user addressable sectors: 80418240 device size with M = 1024*1024: 39266 MBytes device size with M = 1000*1000: 41174 MBytes (41 GB) Capabilities: LBA, IORDY(can be disabled) bytes avail on r/w long: 52 Queue depth: 32 Standby timer values: spec'd by Standard, no device specific minimum R/W multiple sector transfer: Max = 16 Current = 16 Advanced power management level: unknown setting (0x0000) Recommended acoustic management value: 128, current value: 254 DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=240ns IORDY flow control=120ns Commands/features: Enabled Supported: * NOP cmd * READ BUFFER cmd * WRITE BUFFER cmd * Host Protected Area feature set Release interrupt * Look-ahead * Write cache * Power Management feature set Security Mode feature set SMART feature set * FLUSH CACHE EXT command * Mandatory FLUSH CACHE command * Device Configuration Overlay feature set * 48-bit Address feature set Automatic Acoustic Management feature set SET MAX security extension Address Offset Reserved Area Boot SET FEATURES subcommand required to spinup after power up Power-Up In Standby feature set Advanced Power Management feature set * READ/WRITE DMA QUEUED * General Purpose Logging feature set * SMART self-test * SMART error logging Security: Master password revision code = 65534 supported not enabled not locked not frozen not expired: security count not supported: enhanced erase 22min for SECURITY ERASE UNIT. HW reset results: CBLID- above Vih Device num = 0 determined by the jumper Checksum: correct
00:0e.0 Unknown mass storage controller: Promise Technology, Inc. 20269 (rev 02) (prog-if 85) Subsystem: Promise Technology, Inc. Ultra133TX2 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (1000ns min, 4500ns max), Cache Line Size: 0x08 (32 bytes) Interrupt: pin A routed to IRQ 10 Region 0: I/O ports at eff0 [size=8] Region 1: I/O ports at efe4 [size=4] Region 2: I/O ports at efa8 [size=8] Region 3: I/O ports at efe0 [size=4] Region 4: I/O ports at ef90 [size=16] Region 5: Memory at febfc000 (32-bit, non-prefetchable) [size=16K] Expansion ROM at febf8000 [disabled] [size=16K] Capabilities: [60] Power Management version 1 Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
wuuk:/proc/ide/hde# cat settings name value min max mode ---- ----- --- --- ---- acoustic 0 0 254 rw address 1 0 2 rw bios_cyl 16383 0 65535 rw bios_head 255 0 255 rw bios_sect 63 0 63 rw bswap 0 0 1 r current_speed 69 0 70 rw failures 0 0 65535 rw init_speed 69 0 70 rw io_32bit 1 0 3 rw keepsettings 0 0 1 rw lun 0 0 7 rw max_failures 1 0 65535 rw multcount 16 0 16 rw nice1 1 0 1 rw nowerr 0 0 1 rw number 0 0 3 rw pio_mode write-only 0 255 w slow 0 0 1 rw unmaskirq 1 0 1 rw using_dma 1 0 1 rw using_tcq 1 0 32 rw wcache 0 0 1 rw
wuuk:~# dmesg Linux version 2.6.0-test9 (root@wuuk) (gcc version 3.3.2 (Debian)) #1 Wed Oct 29 02:23:54 CET 2003 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001ffe0000 (usable) BIOS-e820: 000000001ffe0000 - 000000001fff8000 (ACPI data) BIOS-e820: 000000001fff8000 - 0000000020000000 (ACPI NVS) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) 511MB LOWMEM available. On node 0 totalpages: 131040 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 126944 pages, LIFO batch:16 HighMem zone: 0 pages, LIFO batch:1 DMI 2.1 present. Building zonelist for node : 0 Kernel command line: root=/dev/hde2 ro vga=3845 Local APIC disabled by BIOS -- reenabling. Found and enabled local APIC! Initializing CPU#0 PID hash table entries: 2048 (order 11: 16384 bytes) Detected 448.128 MHz processor. Console: colour VGA+ 80x30 Memory: 515404k/524160k available (1814k kernel code, 8004k reserved, 675k data, 124k init, 0k highmem) Calibrating delay loop... 884.73 BogoMIPS Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: After generic identify, caps: 0383fbff 00000000 00000000 00000000 CPU: After vendor identify, caps: 0383fbff 00000000 00000000 00000000 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 512K CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040 CPU: Intel Pentium III (Katmai) stepping 03 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX enabled ExtINT on CPU#0 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 447.0981 MHz. ..... host bus clock speed is 99.0551 MHz. NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xfdb91, last bus=1 PCI: Using configuration type 1 mtrr: v2.0 (20020519) drivers/usb/core/usb.c: registered new driver hub PCI: Probing PCI hardware PCI: Probing PCI hardware (bus 00) PCI: Using IRQ router PIIX [8086/7110] at 0000:00:07.0 IA-32 Microcode Update Driver: v1.13 <tigran@veritas.com> Limiting direct PCI/PCI transfers. pty: 256 Unix98 ptys configured Real Time Clock Driver v1.12 Linux agpgart interface v0.100 (c) Dave Jones agpgart: Detected an Intel 440BX Chipset. agpgart: Maximum main memory to use for agp memory: 439M agpgart: AGP aperture is 64M @ 0xf8000000 Using anticipatory io scheduler Floppy drive(s): fd0 is 1.44M floppy0: no floppy controllers found RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) 8139too Fast Ethernet driver 0.9.26 PCI: Found IRQ 5 for device 0000:00:0f.0 eth0: RealTek RTL8139 at 0xe0823c00, 00:02:44:47:f8:69, IRQ 5 eth0: Identified 8139 chip type 'RTL-8100B/8139D' Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx PIIX4: IDE controller at PCI slot 0000:00:07.1 PIIX4: chipset revision 1 PIIX4: not 100% native mode: will probe irqs later ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio hdc: JLMS XJ-HD166S, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 PDC20269: IDE controller at PCI slot 0000:00:0e.0 PCI: Found IRQ 10 for device 0000:00:0e.0 PDC20269: chipset revision 2 PDC20269: ROM enabled at 0xfebf8000 PDC20269: 100% native mode on irq 10 ide2: BM-DMA at 0xef90-0xef97, BIOS settings: hde:pio, hdf:pio ide3: BM-DMA at 0xef98-0xef9f, BIOS settings: hdg:pio, hdh:pio hde: HDS722540VLAT20, ATA DISK drive ide2 at 0xeff0-0xeff7,0xefe6 on irq 10 hde: max request size: 1024KiB hde: 80418240 sectors (41174 MB) w/1794KiB Cache, CHS=16383/255/63, UDMA(100) hde: tagged command queueing enabled, command queue depth 32 hde: hde1 hde2 hde3 end_request: I/O error, dev hdc, sector 0 hdc: ATAPI 48X DVD-ROM drive, 512kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.12 ide-floppy driver 0.99.newide drivers/usb/host/uhci-hcd.c: USB Universal Host Controller Interface driver v2.1 PCI: Found IRQ 9 for device 0000:00:07.2 uhci_hcd 0000:00:07.2: UHCI Host Controller uhci_hcd 0000:00:07.2: irq 9, io base 0000ef40 uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected drivers/usb/core/usb.c: registered new driver hiddev drivers/usb/core/usb.c: registered new driver hid drivers/usb/input/hid-core.c: v2.0:USB HID core driver mice: PS/2 mouse device common for all mice serio: i8042 AUX port at 0x60,0x64 irq 12 input: AT Translated Set 2 keyboard on isa0060/serio0 serio: i8042 KBD port at 0x60,0x64 irq 1 NET: Registered protocol family 2 IP: routing cache hash table of 4096 buckets, 32Kbytes TCP: Hash tables configured (established 32768 bind 65536) NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 15 BIOS EDD facility v0.10 2003-Oct-11, 1 devices found Please report your BIOS at http://domsch.com/linux/edd30/results.html kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 124k freed hub 1-0:1.0: new USB device on port 1, assigned address 2 input: USB HID v1.10 Mouse [Logitech USB Mouse] on usb-0000:00:07.2-1 Adding 124952k swap on /dev/hde1. Priority:-1 extents:1 EXT3 FS on hde2, internal journal eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A microcode: CPU0 updated from revision 0xa to 0xe, date = 09101999
/dev/hde: multcount = 16 (on) IO_support = 1 (32-bit) unmaskirq = 1 (on) using_dma = 1 (on) keepsettings = 0 (off) readonly = 0 (off) readahead = 4096 (on) geometry = 16383/255/63, sectors = 80418240, start = 0
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |