![]() | |||||||||||
Messages in this thread |
The pci id # for the Edimax Ethernet Controller 9130 is not included; init_module failure during driver module loading. Purchased Siemens 1020 Ethernet Card and installed on a PC running Slackware Linux 9.0 kernel 2.4.23-pre5 Card provides instruction on using the tulip driver. Tulip ethernet driver failed when loading its module; failure error init_module - no such device Ran lspci result of lspci: 00:0a.0 Ethernet Controller: Edimax Computer Co.: Unknown Device 9130 (rev 10) Visited the Edimax Computer Co. Website (http://www.edimax.com) and read about 9130 Ethernet Cards; downloaded its driver package (windows and linux); linux driver folder contained a README file instructing to use rtl8139 driver. I've downloaded the rtl8139 driver from the http://www.scyld.com/network/rtl8139.html website and compiled it; when attempting to 'insmod' it again got a response rtl8139.o: init_module: No such device I've tried the new realtek driver 8139too as well with the same failure results. Finally, I've inspected the PCI Ethernet card itself; it has two chips on it. Chip 1 has the following text: RTL8139C 2A031Q1 241B Taiwan Chip 2 has the following text: HE-MX2021 0237 The card itself has the following text: SpeedStream SS1020 Efficient Networks SS10202BE2501467 Below are the error messages that get generated when attempting to load the module and the computer hardware info (I followed your suggestions on what info to include): bash-2.05a# insmod rtl8139.o rtl8139.o: init_module: No such device rtl8139.o: Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg bash-2.05a# modprobe 8139too /lib/modules/2.4.23-pre5/kernel/drivers/net/8139too.o: init_module: No such device /lib/modules/2.4.23-pre5/kernel/drivers/net/8139too.o: Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg /lib/modules/2.4.23-pre5/kernel/drivers/net/8139too.o: insmod /lib/modules/2.4.23-pre5/kernel/drivers/net/8139too.o failed /lib/modules/2.4.23-pre5/kernel/drivers/net/8139too.o: insmod 8139too failed I thnk I'm loading the proper driver but it is having trouble identifying the device. (ethernet card). I'm open for suggesitons how to solve this; my guess is that this card is not included in the pci device list. Below is the computer hardware info: bash-2.05a# lspci 00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge 00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge ( 00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02) 00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) 00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) 00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02) 00:09.0 SCSI storage controller: Adaptec AHA-2940U2/U2W 00:0a.0 Ethernet controller: Edimax Computer Co.: Unknown device 9130 (r 00:0b.0 Multimedia audio controller: IC Ensemble Inc ICE1712 [Envy24] (r 01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200 AGP (r bash-2.05a# lspci -v 00:0a.0 Ethernet controller: Edimax Computer Co.: Unknown device 9130 (rev 10) Subsystem: Efficient Networks, Inc: Unknown device 1020 Flags: bus master, medium devsel, latency 64, IRQ 9 I/O ports at d800 [size=256] Memory at e3000000 (32-bit, non-prefetchable) [size=256] Expansion ROM at e2000000 [disabled] [size=64K] Capabilities: [50] Power Management version 2 bash-2.05a# cat /proc/version Linux version 2.4.23-pre5 (root@BALZAAC) (gcc version 2.95.3 20010315 (release)) #2 SMP Tue Sep 30 20:48:27 EDT 2003 bash-2.05a# cat /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 7 model name : Pentium III (Katmai) stepping : 2 cpu MHz : 451.028 cache size : 512 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr sse bogomips : 897.84 bash-2.05a# cat /proc/modules pci-scan 3784 0 bash-2.05a# bash-2.05a# cat /proc/ioports 0000-001f : dma1 0020-003f : pic1 0040-005f : timer 0060-006f : keyboard 0080-008f : dma page reg 00a0-00bf : pic2 00c0-00df : dma2 00f0-00ff : fpu 02f8-02ff : serial(auto) 03c0-03df : vga+ 03c0-03df : matrox 03f8-03ff : serial(auto) 0cf8-0cff : PCI conf1 4000-403f : Intel Corp. 82371AB/EB/MB PIIX4 ACPI 5000-501f : Intel Corp. 82371AB/EB/MB PIIX4 ACPI c000-cfff : PCI Bus #01 d000-d01f : Intel Corp. 82371AB/EB/MB PIIX4 USB d400-d4ff : Adaptec AHA-2940U2/U2W d800-d8ff : PCI device 1432:9130 (Edimax Computer Co.) dc00-dc1f : IC Ensemble Inc ICE1712 [Envy24] e000-e00f : IC Ensemble Inc ICE1712 [Envy24] e400-e40f : IC Ensemble Inc ICE1712 [Envy24] e800-e83f : IC Ensemble Inc ICE1712 [Envy24] f000-f00f : Intel Corp. 82371AB/EB/MB PIIX4 IDE bash-2.05a# cat /proc/iomem 00000000-0009fbff : System RAM 0009fc00-0009ffff : reserved 000a0000-000bffff : Video RAM area 000c0000-000c7fff : Video ROM 000c8000-000ce5ff : Extension ROM 000f0000-000fffff : System ROM 00100000-27feffff : System RAM 00100000-00251f64 : Kernel code 00251f65-002e825f : Kernel data 27ff0000-27ff2fff : ACPI Non-volatile Storage 27ff3000-27ffffff : ACPI Tables d8000000-dbffffff : Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge dc000000-dfffffff : PCI Bus #01 dc000000-dc003fff : Matrox Graphics, Inc. MGA G200 AGP dc000000-dc003fff : matroxfb MMIO dd000000-dd7fffff : Matrox Graphics, Inc. MGA G200 AGP e0000000-e0ffffff : PCI Bus #01 e0000000-e0ffffff : Matrox Graphics, Inc. MGA G200 AGP e0000000-e0ffffff : matroxfb FB e3000000-e30000ff : PCI device 1432:9130 (Edimax Computer Co.) e3001000-e3001fff : Adaptec AHA-2940U2/U2W e3001000-e3001fff : aic7xxx ffff0000-ffffffff : reserved bash-2.05a# 00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 64 Region 0: Memory at d8000000 (32-bit, prefetchable) [size=64M] Capabilities: [a0] AGP version 1.0 Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2 Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none> 00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Bus: primary=00, secondary=01, subordinate=01, sec-latency=64 I/O behind bridge: 0000c000-0000cfff Memory behind bridge: dc000000-dfffffff Prefetchable memory behind bridge: e0000000-e0ffffff BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B+ 00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) (prog-if 80 [Master]) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Region 4: I/O ports at f000 [size=16] 00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) (prog-if 00 [UHCI]) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- arErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Interrupt: pin D routed to IRQ 10 Region 4: I/O ports at d000 [size=32] 00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02) Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin ? routed to IRQ 9 00:09.0 SCSI storage controller: Adaptec AHA-2940U2/U2W Subsystem: Adaptec AHA-2940U2W SCSI Controller Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (9750ns min, 6250ns max) Interrupt: pin A routed to IRQ 5 BIST result: 00 Region 0: I/O ports at d400 [disabled] [size=256] Region 1: Memory at e3001000 (64-bit, non-prefetchable) [size=4K] Expansion ROM at e1000000 [disabled] [size=128K] Capabilities: [dc] Power Management version 1 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:0a.0 Ethernet controller: Edimax Computer Co.: Unknown device 9130 (rev 10) Subsystem: Efficient Networks, Inc: Unknown device 1020 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- Fast B2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR - <PERR- Latency: 64 (8000ns min, 16000ns max) Interrupt: pin A routed to IRQ 9 Region 0: I/O ports at d800 [size=256] Region 1: Memory at e3000000 (32-bit, non-prefetchable) [size=256] Expansion ROM at e2000000 [disabled] [size=64K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:0b.0 Multimedia audio controller: IC Ensemble Inc ICE1712 [Envy24] (rev 02) Subsystem: IC Ensemble Inc: Unknown device d630 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- Fast B2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR - <PERR- Latency: 64 Interrupt: pin A routed to IRQ 10 Region 0: I/O ports at dc00 [size=32] Region 1: I/O ports at e000 [size=16] Region 2: I/O ports at e400 [size=16] Region 3: I/O ports at e800 [size=64] Capabilities: [80] Power Management version 1 Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200 AGP (rev 01) (prog-if 00 [VGA] ) Subsystem: Matrox Graphics, Inc. MGA-G200 AGP Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- Fast B2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR - <PERR- Latency: 64 (4000ns min, 8000ns max), cache line size 08 Interrupt: pin A routed to IRQ 11 Region 0: Memory at e0000000 (32-bit, prefetchable) [size=16M] Region 1: Memory at dc000000 (32-bit, non-prefetchable) [size=16K] Region 2: Memory at dd000000 (32-bit, non-prefetchable) [size=8M] Expansion ROM at <unassigned> [disabled] [size=64K] Capabilities: [dc] Power Management version 1 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [f0] AGP version 1.0 Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2 Command: RQ=31 SBA+ AGP+ 64bit- FW- Rate=x2 bash-2.05a# cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: WDIGTL Model: WDE9100 ULTRA2 Rev: 1.22 Type: Direct-Access ANSI SCSI revision: 02 Host: scsi0 Channel: 00 Id: 02 Lun: 00 Vendor: TOSHIBA Model: CD-ROM XM-6401TA Rev: 1009 Type: CD-ROM ANSI SCSI revision: 02 Host: scsi0 Channel: 00 Id: 15 Lun: 00 Vendor: WDIGTL Model: WDE18300 ULTRA2 Rev: 1.30 Type: Direct-Access ANSI SCSI revision: 02 bash-2.05a# Regards ... Yarek "Only two things are infinite, the universe and human stupidity, and I'm not sure about the former." - Albert Einstein - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/ | ||||||||||
| Last update: 2005-03-22 13:49 [from the cache] ©2003-2008 | |||||||||||