lkml.org 
[lkml]   [2002]   [Jun]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: Another -pre
From
Date
On the IDE fixes note, I am using a HighPoint card with the HPT302
chipset - I can get the primary IDE channel to work perfectly, but the
secondary doesn't show up.


Below is a DMESG:

Matt


PS - I'm trying to be helpful and think this is the proper way to do it.
Please let me know if I am mistaken or need to do something differently.




Linux version 2.4.19-pre9-ac2 (root@mattswork) (gcc version 2.96
20000731 (Red Hat Linux 7.3 2.96-110)) #1 SMP Mon Jun 3 11:57:00 PDT
2002
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fffd000 (usable)
BIOS-e820: 000000003fffd000 - 000000003ffff000 (ACPI data)
BIOS-e820: 000000003ffff000 - 0000000040000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f6e50
hm, page 000f6000 reserved twice.
hm, page 000f7000 reserved twice.
hm, page 000f6000 reserved twice.
hm, page 000f7000 reserved twice.
On node 0 totalpages: 262141
zone(0): 4096 pages.
zone(1): 225280 pages.
zone(2): 32765 pages.
Intel MultiProcessor Specification v1.1
Virtual Wire compatibility mode.
OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
Processor #1 Pentium(tm) Pro APIC version 17
Processor #0 Pentium(tm) Pro APIC version 17
I/O APIC #2 Version 17 at 0xFEC00000.
Processors: 2
Kernel command line: auto BOOT_IMAGE=linux-2.4.19p9 ro root=806
BOOT_FILE=/boot/vmlinuz-2.4.19.pre9-ac hda=ide-scsi
ide_setup: hda=ide-scsi
Initializing CPU#0
Detected 451.034 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 897.84 BogoMIPS
Memory: 1030600k/1048564k available (1823k kernel code, 17576k reserved,
549k data, 288k init, 131060k highmem)
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode cache hash table entries: 65536 (order: 7, 524288 bytes)
Mount cache hash table entries: 16384 (order: 5, 131072 bytes)
Buffer cache hash table entries: 65536 (order: 6, 262144 bytes)
Page-cache hash table entries: 262144 (order: 8, 1048576 bytes)
CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
CPU0: Intel Pentium III (Katmai) stepping 03
per-CPU timeslice cutoff: 1461.42 usecs.
task migration cache decay timeout: 10 msecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Booting processor 1/0 eip 2000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 901.12 BogoMIPS
CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000
Intel machine check reporting enabled on CPU#1.
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
CPU1: Intel Pentium III (Katmai) stepping 03
Total of 2 processors activated (1798.96 BogoMIPS).
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-5, 2-9, 2-10, 2-11, 2-13, 2-20, 2-21, 2-22,
2-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 15.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................

IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
.... register #01: 00170011
....... : max redirection entries: 0017
....... : PRQ implemented: 0
....... : IO APIC version: 0011
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 003 03 0 0 0 0 0 1 1 39
02 003 03 0 0 0 0 0 1 1 31
03 003 03 0 0 0 0 0 1 1 41
04 003 03 0 0 0 0 0 1 1 49
05 000 00 1 0 0 0 0 0 0 00
06 003 03 0 0 0 0 0 1 1 51
07 003 03 0 0 0 0 0 1 1 59
08 003 03 0 0 0 0 0 1 1 61
09 000 00 1 0 0 0 0 0 0 00
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 003 03 0 0 0 0 0 1 1 69
0d 000 00 1 0 0 0 0 0 0 00
0e 003 03 0 0 0 0 0 1 1 71
0f 003 03 0 0 0 0 0 1 1 79
10 003 03 1 1 0 1 0 1 1 81
11 003 03 1 1 0 1 0 1 1 89
12 003 03 1 1 0 1 0 1 1 91
13 003 03 1 1 0 1 0 1 1 99
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:18
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:19
IRQ10 -> 0:17
IRQ11 -> 0:16
IRQ12 -> 0:12
IRQ14 -> 0:14
IRQ15 -> 0:15
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 451.0322 MHz.
..... host bus clock speed is 100.2291 MHz.
cpu: 0, clocks: 1002291, slice: 334097
CPU0<T0:1002288,T1:668176,D:15,S:334097,C:1002291>
cpu: 1, clocks: 1002291, slice: 334097
CPU1<T0:1002288,T1:334080,D:14,S:334097,C:1002291>
checking TSC synchronization across CPUs: passed.
migration_task 0 on cpu=0
migration_task 1 on cpu=1
PCI: PCI BIOS revision 2.10 entry at 0xf0730, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 0: assuming transparent
PCI: Using IRQ router PIIX [8086/7110] at 00:04.0
Limiting direct PCI/PCI transfers.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
allocated 32 pages and 32 bhs reserved for the highmem bounces
Journalled Block Device driver loaded
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ
SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
block: 1024 slots per queue, batch=256
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 21
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:pio, hdd:pio
HPT302: IDE controller on PCI bus 00 dev 60
HPT302: chipset revision 1
HPT302: not 100% native mode: will probe irqs later
HPT37X: using 33MHz PCI clock
ide2: BM-DMA at 0x9800-0x9807, BIOS settings: hde:DMA, hdf:pio
hda: Hewlett-Packard CD-Writer Plus 8100, ATAPI CD/DVD-ROM drive
hde: WDC WD400BB-00CFC0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide2 at 0xb000-0xb007,0xa802 on irq 11
hde: host protected area => 1
hde: 78165360 sectors (40021 MB) w/2048KiB Cache, CHS=77545/16/63,
UDMA(100)
Partition check:
hde: [PTBL] [4865/255/63] hde1
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
loop: loaded (max 8 devices)
Linux Tulip driver version 0.9.15-pre11 (May 11, 2002)
eth0: Macronix 98715 PMAC rev 32 at 0xd000, 00:80:C6:F7:82:05, IRQ 9.
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 816M
agpgart: Detected Intel 440BX chipset
agpgart: AGP aperture is 64M @ 0xe4000000
[drm] Initialized tdfx 1.0.0 20010216 on minor 0
[drm] AGP 0.99 on Intel 440BX @ 0xe4000000 64MB
[drm] Initialized radeon 1.1.1 20010405 on minor 1
SCSI subsystem driver Revision: 1.00
scsi: ***** BusLogic SCSI Driver Version 2.1.15 of 17 August 1998 *****
scsi: Copyright 1995-1998 by Leonard N. Zubkoff <lnz@dandelion.com>
scsi0: Configuring BusLogic Model BT-958 PCI Wide Ultra SCSI Host
Adapter
scsi0: Firmware Version: 5.06I, I/O Address: 0xB400, IRQ Channel:
10/Level
scsi0: PCI Bus: 0, Device: 11, Address: 0xDE800000, Host Adapter SCSI
ID: 7
scsi0: Parity Checking: Enabled, Extended Translation: Enabled
scsi0: Synchronous Negotiation: Ultra, Wide Negotiation: Enabled
scsi0: Disconnect/Reconnect: Enabled, Tagged Queuing: Enabled
scsi0: Scatter/Gather Limit: 128 of 8192 segments, Mailboxes: 211
scsi0: Driver Queue Depth: 211, Host Adapter Queue Depth: 192
scsi0: Tagged Queue Depth: Automatic, Untagged Queue Depth: 3
scsi0: Error Recovery Strategy: Default, SCSI Bus Reset: Enabled
scsi0: SCSI Bus Termination: Both Enabled, SCAM: Enabled, Level 1
scsi0: *** BusLogic BT-958 Initialized Successfully ***
scsi0 : BusLogic BT-958
Vendor: SEAGATE Model: ST318451LW Rev: 0003
Type: Direct-Access ANSI SCSI revision: 03
Vendor: SEAGATE Model: ST39103LW Rev: 0001
Type: Direct-Access ANSI SCSI revision: 02
scsi0: Target 0: Queue Depth 28, Wide Synchronous at 40.0 MB/sec, offset
15
scsi0: Target 14: Queue Depth 28, Wide Synchronous at 40.0 MB/sec,
offset 15
scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.8
<Adaptec 2902/04/10/15/20/30C SCSI adapter>
aic7850: Single Channel A, SCSI Id=7, 3/253 SCBs

Vendor: SEAGATE Model: DAT 06240-XXX Rev: 8110
Type: Sequential-Access ANSI SCSI revision: 03
(scsi1:A:4): 10.000MB/s transfers (10.000MHz, offset 15)
scsi2 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: HP Model: CD-Writer+ 8100 Rev: 1.0g
Type: CD-ROM ANSI SCSI revision: 02
st: Version 20020205, bufsize 32768, wrt 30720, max init. bufs 4, s/g
segs 16
Attached scsi tape st0 at scsi1, channel 0, id 4, lun 0
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi disk sdb at scsi0, channel 0, id 14, lun 0
SCSI device sda: 35843671 512-byte hdwr sectors (18352 MB)
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 >
SCSI device sdb: 17783240 512-byte hdwr sectors (9105 MB)
sdb: sdb1 sdb2
Attached scsi CD-ROM sr0 at scsi2, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
usb.c: registered new driver hub
uhci.c: USB Universal Host Controller Interface driver v1.1
uhci.c: USB UHCI at I/O 0xd400, IRQ 9
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 288k freed
scsi0: Tagged Queuing now active for Target 0
Adding Swap: 2048248k swap-space (priority -1)

On Mon, 2002-06-03 at 17:15, Alan Cox wrote:
> On Mon, 2002-06-03 at 15:55, Marcelo Tosatti wrote:
> > On Mon, 3 Jun 2002, Pawel Kot wrote:
> >
> > > On Mon, 3 Jun 2002, Marcelo Tosatti wrote:
> > >
> > > > Due to some missing network fixes and -ac merge, I'll release another -pre
> > > > later today.
> > > >
> > > > -rc should be out by the end of the week.
> > >
> > > Would you please consider merging some IDE updates before releasing
> > > 2.4.19? Current version remains unusable for me.
> > > See http://marc.theaimsgroup.com/?l=linux-kernel&m=102277249800423&w=2
> > > and followers for more detailes.
> >
> > Andre,
> >
> > Have you looked into this problem ?
>
> With the current code I've got these items on my list I class as
> problematic.
>
> 1 Weird corruption report with AMD chipset in PIO mode
> 1 NULL pointer crash report on SiS chipset
> 2 Intel 845G issues (PIO only, incorrect BIOS setup)
> 1 set of requested Promise changes
>
> The 845G and Promise ones are present in both. The AMD one is utterly
> weird and I'm still looking at the SiS one.



-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2005-03-22 13:26    [W:0.090 / U:0.284 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site