lkml.org 
[lkml]   [2002]   [Mar]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: PDC20269 error handling problem
The attached patch "fixes" the bug. How bad sectors cause just sector
errors, no more system hangs. The patch is not perfect, but definitively
an improvement:

<<<<<<<
hde: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hde: dma_intr: error=0x01 { AddrMarkNotFound }, LBAsect=43141736,
high=2, low=9587304, sector=43141736
hde: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hde: dma_intr: error=0x01 { AddrMarkNotFound }, LBAsect=43141736,
high=2, low=9587304, sector=43141736
hde: DMA disabled
PDC202XX: Primary channel reset.
ide2: reset: master: error (0x00?)
hde: task_in_intr: status=0x59 { DriveReady SeekComplete DataRequest
Error }
hde: task_in_intr: error=0x40 { UncorrectableError }, LBAsect=43141736,
high=2, low=9587304, sector=43141736
end_request: I/O error, dev 21:00 (hde), sector 43141736
hde: task_in_intr: status=0x59 { DriveReady SeekComplete DataRequest
Error }
hde: task_in_intr: error=0x40 { UncorrectableError }, LBAsect=43141736,
high=2, low=9587304, sector=43141736
<<<

I think "master: error (0x00?)" indicate another bug.
Andre, what do you think?

--
Manfred--- 2.4/drivers/ide/pdc202xx.c Fri Mar 29 14:34:13 2002
+++ build-2.4/drivers/ide/pdc202xx.c Sun Mar 31 01:04:02 2002
@@ -729,12 +729,7 @@
byte mask = hwif->channel ? 0x08 : 0x02;
unsigned short c_mask = hwif->channel ? (1<<11) : (1<<10);

- byte ultra_66 = ((id->dma_ultra & 0x0010) ||
- (id->dma_ultra & 0x0008)) ? 1 : 0;
- byte ultra_100 = ((id->dma_ultra & 0x0020) ||
- (ultra_66)) ? 1 : 0;
- byte ultra_133 = ((id->dma_ultra & 0x0040) ||
- (ultra_100)) ? 1 : 0;
+ byte fast_ultra = id->dma_ultra & 0x0078;

switch(dev->device) {
case PCI_DEVICE_ID_PROMISE_20276:
@@ -792,7 +787,7 @@
* parameters.
*/

- if (((ultra_66) || (ultra_100) || (ultra_133)) && (cable)) {
+ if (fast_ultra && cable) {
#ifdef DEBUG
printk("ULTRA66: %s channel of Ultra 66 requires an 80-pin cable for Ultra66 operation.\n", hwif->channel ? "Secondary" : "Primary");
printk(" Switching to Ultra33 mode.\n");
@@ -805,17 +800,13 @@
printk("%s reduced to Ultra33 mode.\n", drive->name);
udma_66 = 0; udma_100 = 0; udma_133 = 0;
} else {
- if ((ultra_66) || (ultra_100) || (ultra_133)) {
+ if (fast_ultra) {
/*
* check to make sure drive on same channel
* is u66 capable
*/
if (hwif->drives[!(drive->dn%2)].id) {
- if ((hwif->drives[!(drive->dn%2)].id->dma_ultra & 0x0040) ||
- (hwif->drives[!(drive->dn%2)].id->dma_ultra
-& 0x0020) ||
- (hwif->drives[!(drive->dn%2)].id->dma_ultra & 0x0010) ||
- (hwif->drives[!(drive->dn%2)].id->dma_ultra & 0x0008)) {
+ if (hwif->drives[!(drive->dn%2)].id->dma_ultra & 0x0078) {
if (!jumpbit)
OUT_BYTE(CLKSPD | mask, (high_16 + 0x11));
} else {
@@ -1075,6 +1066,8 @@
mdelay(1000);
printk("PDC202XX: %s channel reset.\n",
HWIF(drive)->channel ? "Secondary" : "Primary");
+ /* the reset clears the configuration, reinit to pio */
+ config_chipset_for_pio(drive, 5);
}

void pdc202xx_reset (ide_drive_t *drive)
\
 
 \ /
  Last update: 2005-03-22 13:25    [W:0.046 / U:0.028 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site