Messages in this thread | | | Date | Sat, 30 Mar 2002 14:27:58 +0100 (CET) | From | Jim MacBaine <> | Subject | PDC20268 broke in 2.4.19-pre4-ac3 |
| |
The Promise PDC20268 driver fails with my setup in 2.4.19-pre4-ac3. The same setup works fine for about three weeks with 2.4.19-pre2-ac4.
The configuration remained unchanged except for serial console support to read the kernel messages.
There are two IBM harddisks attached to the first channel, a single HP CDRW on the secound channel of a Promise Ultra100 TX2:
hde: IC35L060AVER07-0, ATA DISK drive hdf: IBM-DJNA-352030, ATA DISK drive hdh: R/RW 4x4x32, ATAPI CD/DVD-ROM drive
Although the kernel says,
Warning: Primary channel requires an 80-pin cable for operation.
I swear the two disks on the first channel are connected with an original Promise UDMA/100 cable. The CDRW is not connected with an 80-pin cable, but works well with 2.4.19-pre2-ac4.
Please see the attached file for the full startup log.
Regards, Jim
__________________________________________________________________
Gesendet von Yahoo! Mail - http://mail.yahoo.de Sie brauchen mehr Speicher für Ihre E-Mails? - http://premiummail.yahoo.deLinux version 2.4.19-pre4-ac3 (jim@pluto) (gcc version 2.95.3 20010315 (SuSE)) #3 Sat Mar 30 13:00:23 CET 2002 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000002fff0000 (usable) BIOS-e820: 000000002fff0000 - 000000002fff3000 (ACPI NVS) BIOS-e820: 000000002fff3000 - 0000000030000000 (ACPI data) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) On node 0 totalpages: 196592 zone(0): 4096 pages. zone(1): 192496 pages. zone(2): 0 pages. Kernel command line: BOOT_IMAGE=normal-new ro root=101 BOOT_FILE=/boot/vmlinuz-2.4.19-pre4-ac3 console=ttyS0 Initializing CPU#0 Detected 864.473 MHz processor. Console: colour VGA+ 80x25 Calibrating delay loop... 1723.59 BogoMIPS Memory: 774268k/786368k available (923k kernel code, 11712k reserved, 311k data, 228k init, 0k highmem) Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) Inode cache hash table entries: 65536 (order: 7, 524288 bytes) Mount cache hash table entries: 16384 (order: 5, 131072 bytes) Buffer cache hash table entries: 65536 (order: 6, 262144 bytes) Page-cache hash table entries: 262144 (order: 8, 1048576 bytes) CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 256K Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: Intel Pentium III (Coppermine) stepping 03 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au) mtrr: detected mtrr type: Intel PCI: PCI BIOS revision 2.10 entry at 0xfb290, last bus=1 PCI: Using configuration type 1 PCI: Probing PCI hardware Unknown bridge resource 0: assuming transparent PCI: Using IRQ router VIA [1106/0596] at 00:07.0 Activating ISA DMA hang workarounds. PnPBIOS: Found PnP BIOS installation structure at 0xc00fbce0 PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xbd10, dseg 0xf0000 PnPBIOS: 14 nodes reported by PnP BIOS; 14 recorded by driver Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16) Starting kswapd Journalled Block Device driver loaded devfs: v1.10 (20020120) Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x0 pty: 256 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A Real Time Clock Driver v1.10e block: 1024 slots per queue, batch=256 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 6.31 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller on PCI bus 00 dev 39 VP_IDE: chipset revision 16 VP_IDE: not 100% native mode: will probe irqs later ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: VIA vt82c596b (rev 23) IDE UDMA66 controller on pci00:07.1 ide0: BM-DMA at 0xc000-0xc007, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xc008-0xc00f, BIOS settings: hdc:DMA, hdd:DMA PDC20268: IDE controller on PCI bus 00 dev 60 PCI: Found IRQ 11 for device 00:0c.0 PCI: Sharing IRQ 11 with 00:0d.0 PDC20268: chipset revision 1 PDC20268: not 100% native mode: will probe irqs later ide2: BM-DMA at 0xdc00-0xdc07, BIOS settings: hde:pio, hdf:pio ide3: BM-DMA at 0xdc08-0xdc0f, BIOS settings: hdg:pio, hdh:pio hda: Maxtor 34098H4, ATA DISK drive hdc: _NEC DV-5500A, ATAPI CD/DVD-ROM drive hdd: CDD4801 CD-R/RW, ATAPI CD/DVD-ROM drive hde: IC35L060AVER07-0, ATA DISK drive hdf: IBM-DJNA-352030, ATA DISK drive hdh: R/RW 4x4x32, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 ide2 at 0xcc00-0xcc07,0xd002 on irq 11 ide3 at 0xd400-0xd407,0xd802 on irq 11 hda: 78165360 sectors (40021 MB) w/2048KiB Cache, CHS=4865/255/63, UDMA(66) hde: 120103200 sectors (61493 MB) w/1916KiB Cache, CHS=119150/16/63, UDMA(100) hdf: set_drive_speed_status: status=0xff { Busy } Warning: Primary channel requires an 80-pin cable for operation. hdf reduced to Ultra33 mode. hdf: set_drive_speed_status: status=0xff { Busy } hdf: status timeout: status=0xff { Busy } hdf: drive not ready for command hdf: 39876480 sectors (20417 MB) w/1966KiB Cache, CHS=39560/16/63, (U)DMA Partition check: /dev/ide/host0/bus0/target0/lun0: p1 p2 p3 /dev/ide/host2/bus0/target0/lun0:hde: status timeout: status=0xff { Busy } hde: DMA disabled hdf: DMA disabled PDC202XX: Primary channel reset. hde: drive not ready for command ide2: reset timed-out, status=0xff hde: status timeout: status=0xff { Busy } PDC202XX: Primary channel reset. hde: drive not ready for command ide2: reset timed-out, status=0xff end_request: I/O error, dev 21:00 (hde), sector 0 end_request: I/O error, dev 21:00 (hde), sector 2 end_request: I/O error, dev 21:00 (hde), sector 4 end_request: I/O error, dev 21:00 (hde), sector 6 end_request: I/O error, dev 21:00 (hde), sector 0 end_request: I/O error, dev 21:00 (hde), sector 2 end_request: I/O error, dev 21:00 (hde), sector 4 end_request: I/O error, dev 21:00 (hde), sector 6 unable to read partition table /dev/ide/host2/bus0/target1/lun0:hdf: status timeout: status=0xff { Busy } PDC202XX: Primary channel reset. hdf: drive not ready for command ide2: reset timed-out, status=0xff hdf: status timeout: status=0xff { Busy } PDC202XX: Primary channel reset. hdf: drive not ready for command ide2: reset timed-out, status=0xff end_request: I/O error, dev 21:40 (hdf), sector 0 end_request: I/O error, dev 21:40 (hdf), sector 2 end_request: I/O error, dev 21:40 (hdf), sector 4 end_request: I/O error, dev 21:40 (hdf), sector 6 end_request: I/O error, dev 21:40 (hdf), sector 0 end_request: I/O error, dev 21:40 (hdf), sector 2 end_request: I/O error, dev 21:40 (hdf), sector 4 end_request: I/O error, dev 21:40 (hdf), sector 6 unable to read partition table NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP IP: routing cache hash table of 8192 buckets, 64Kbytes TCP: Hash tables configured (established 262144 bind 65536) RAMDISK: Compressed image found at block 0 Freeing initrd memory: 1k freed VFS: Mounted root (minix filesystem).
| |