lkml.org 
[lkml]   [2002]   [Oct]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
Subject[BK/GNU] net driver series 11
Marcelo, please do a

bk pull http://gkernel.bkbits.net/net-drivers-2.4

This will update the following files:

Documentation/networking/e100.txt | 99 ++++------
Documentation/networking/e1000.txt | 22 +-
drivers/net/e100/e100.h | 8
drivers/net/e100/e100_main.c | 220 ++++++++---------------
drivers/net/e100/e100_proc.c | 22 +-
drivers/net/e1000/e1000.h | 10 +
drivers/net/e1000/e1000_ethtool.c | 29 ---
drivers/net/e1000/e1000_hw.c | 56 ++++-
drivers/net/e1000/e1000_hw.h | 33 ++-
drivers/net/e1000/e1000_main.c | 167 +++++++++++------
drivers/net/e1000/e1000_osdep.h | 2
drivers/net/e1000/e1000_param.c | 105 +++++------
drivers/net/e1000/e1000_proc.c | 30 +--
drivers/net/eepro100.c | 349 +++++++++++++++++++------------------
drivers/net/ewrk3.c | 320 ++++++++++++++++++++++++++++-----
drivers/net/mii.c | 11 -
drivers/net/natsemi.c | 6
drivers/net/pcnet32.c | 36 +++
18 files changed, 892 insertions(+), 633 deletions(-)

through these ChangeSets:

<thockin@freakshow.cobalt.com> (02/10/23 1.746.1.5)
drivers/net/eepro100.c: set phy_id_mask and reg_num_mask in mii_if

<thockin@freakshow.cobalt.com> (02/10/23 1.746.1.4)
drivers/net/mii.c: fix flipped logic

<thockin@freakshow.cobalt.com> (02/10/23 1.746.1.3)
drivers/net/eepro100.c: set the PHY ID correctly

<key@austin.ibm.com> (02/10/21 1.749.1.7)
Add link status checking to pcnet32 net driver

<akropel1@rochester.rr.com> (02/10/21 1.749.1.5)
Last ewrk3 for now. Updates the changelog to cover previous patches, bumps the
revision number, and replaces the horrific EthwrkSignature function with
something (slightly) less horrific.

<akropel1@rochester.rr.com> (02/10/21 1.749.1.4)
This patch adds some locking fixups to the ewrk3 ioctl routine. None of these
are critical since the ioctls AFAIK are used only by the EEPROM config utility.

<jgarzik@redhat.com> (02/10/21 1.749.1.3)
Remove cli/sti from ewrk3 net driver.
Also, comment out ETHTOOL_PHYS_ID until its sleeping is fixed.

Originally by Denis Vlasenko, then via Adam Kropelin, and
finally cleaned up by me.

<thockin@freakshow.cobalt.com> (02/10/21 1.746.1.2)
drivers/net/eepro100.c: cleanup messages that pop up since netif_msg_xxx change

<akropel1@rochester.rr.com> (02/10/21 1.749.1.2)
The following patch adds support for ethtool to the ewrk3 driver. It is against
2.5-BK but should apply to any recent 2.5 and 2.4 as well. In addition to adding
ethtool support, it also removes the cli/sti fixup attribution from the
changelog since that didn't actually go in yet and fixes a small style issue I
introduced in the multi-card support patch.

This has been tested on an SMP x86 box containing 3 DE205 NICs.

<scott.feldman@intel.com> (02/10/18 1.742.1.18)
e100 5/5:
* updates to Documentation/networking/e100.txt


<scott.feldman@intel.com> (02/10/18 1.742.1.17)
e100 4/5:
* Updated change log
* Adding notifier to track ifname change for /proc info


<scott.feldman@intel.com> (02/10/18 1.742.1.16)
e100 3/5:
* Added meaningful message for self-test failures
* Removed confusing messages from probe when link isn't detected


<scott.feldman@intel.com> (02/10/18 1.742.1.15)
e100 2/5:
* Remove broken home-grown Rx polling mode (make way for NAPI)


<scott.feldman@intel.com> (02/10/18 1.742.1.14)
e100 1/5:
* C99 struct initializer format


<jeb.j.cramer@intel.com> (02/10/18 1.742.1.13)
e1000 11/11:
* Documentation/networking/e1000.txt updates


<jeb.j.cramer@intel.com> (02/10/18 1.742.1.12)
e1000 10/11:
* C99 struct initializer format


<jeb.j.cramer@intel.com> (02/10/18 1.742.1.11)
e1000 9/11:
* Added bullets to changelog
* Whitespace cleanup


<jeb.j.cramer@intel.com> (02/10/18 1.742.1.10)
e1000 8/11:
* Forcing 1000/fd is easier to undo with ethtool
* Adapters supporting WoL capabilities are now an inclusive versus
exclusive list


<jeb.j.cramer@intel.com> (02/10/18 1.742.1.9)
e1000 7/11:
* Added software interrupt to ensure rx ring is cleaned in case
of previous allocation failures
* Filled netdev->mem_end member


<jeb.j.cramer@intel.com> (02/10/18 1.742.1.8)
e1000 6/11:
* Adding notifier to track ifname change for /proc info


<jeb.j.cramer@intel.com> (02/10/18 1.742.1.7)
e1000 5/11:
* 2/3 wire downshift phy bits changed in newer phy revs


<jeb.j.cramer@intel.com> (02/10/18 1.742.1.6)
e1000 4/11:
* Newer controllers required manual phy PM enable for WoL to work


<jeb.j.cramer@intel.com> (02/10/18 1.742.1.5)
e1000 3/11:
* Set interrupt delay timer default to 0 across all adapters


<jeb.j.cramer@intel.com> (02/10/18 1.742.1.4)
e1000 2/11:
* Changed flow control defaults to minimize packet drops


<jeb.j.cramer@intel.com> (02/10/18 1.742.1.3)
e1000 1/11:
* add new pci ids

<thockin@freakshow.cobalt.com> (02/10/17 1.742.1.2)
drivers/net/eepro100.c: eliminate speedo_intrmask

<thockin@freakshow.cobalt.com> (02/10/17 1.737.3.8)
drivers/net/eepro100.c: compile bugs

<thockin@freakshow.cobalt.com> (02/10/16 1.737.3.7)
drivers/net/natsemi.c: init msg_enable in proper way

<sparker@sun.com> (02/10/16 1.737.3.6)
drivers/net/eepro100.c: mask the interrupt and do a small delay on close()

<sparker@sun.com> (02/10/16 1.737.3.5)
drivers/net/eepro100.c: only set priv->last_rx_time if we did work

<sparker@sun.com> (02/10/16 1.737.3.4)
drivers/net/eepro100.c: simplify wait_for_cmd_done(), better errors

<thockin@freakshow.cobalt.com> (02/10/16 1.737.3.3)
drivers/net/eepro100.c:
* use netif_msg_xxx() instead of speedo_debug
* better default debug mask, proper use of debug module param
* add ETHTOOL_[GS]MSGLVL

<thockin@freakshow.cobalt.com> (02/10/14 1.737.3.2)
drivers/net/mii.c: only call netif_carrier_{on,off} if there is a state change

<thockin@freakshow.cobalt.com> (02/10/14 1.737.3.1)
drivers/net/eepro100.c:
* mii cleanups
* use mii_check_link()
* check link every timer

[unhandled content-type:application/x-bzip2]
\
 
 \ /
  Last update: 2005-03-22 13:30    [W:0.026 / U:0.620 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site