lkml.org 
[lkml]   [2001]   [Jun]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    Date
    From
    SubjectRe: Cleanup kbuild for aic7xxx
    Here is the output of a plain jane 2.4.5 compile with the 'new' adaptec 
    compiled in:

    Linux version 2.4.5 (root@James) (gcc version 2.95.3 20010315 (release))
    #3 Fri
    Jun 22 21:23:04 PDT 2001
    ...
    Kernel command line: BOOT_IMAGE=test ro root=801 BOOT_FILE=/boot/test
    aic7xxx=verbose nmi_watchdog=1 console=ttyS0,38400 console=tty0
    serial=0,38400n8
    ...
    ahc_pci:0:12:0: Reading SEEPROM...done.
    ahc_pci:0:12:0: Manual LVD Termination
    ahc_pci:0:12:0: BIOS eeprom not present
    ahc_pci:0:12:0: Secondary High byte termination Enabled
    ahc_pci:0:12:0: Primary Low Byte termination Enabled
    ahc_pci:0:12:0: Primary High Byte termination Enabled
    ahc_pci:0:12:0: Downloading Sequencer Program... 416 instructions downloaded
    PCI: Found IRQ 10 for device 00:0c.1
    PCI: The same IRQ used for device 00:0c.0
    ahc_pci:0:12:1: Reading SEEPROM...done.
    ahc_pci:0:12:1: Manual LVD Termination
    ahc_pci:0:12:1: BIOS eeprom not present
    ahc_pci:0:12:1: Secondary High byte termination Enabled
    ahc_pci:0:12:1: Primary Low Byte termination Enabled
    ahc_pci:0:12:1: Primary High Byte termination Enabled
    ahc_pci:0:12:1: Downloading Sequencer Program... 416 instructions downloaded
    scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.1.13
    <Adaptec aic7896/97 Ultra2 SCSI adapter>
    aic7896/97: Ultra2 Wide Channel B, SCSI Id=7, 32/255 SCBs

    scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.1.13
    <Adaptec aic7896/97 Ultra2 SCSI adapter>
    aic7896/97: Ultra2 Wide Channel A, SCSI Id=7, 32/255 SCBs

    Now it breaks

    scsi0:0:0:0: Attempting to queue an ABORT message
    scsi0: Dumping Card State while idle, at SEQADDR 0x8
    SCSISEQ = 0x12, SBLKCTL = 0x6
    DFCNTRL = 0x0, DFSTATUS = 0x89
    LASTPHASE = 0x1, SCSISIGI = 0x0, SXFRCTL0 = 0x80
    SSTAT0 = 0x0, SSTAT1 = 0xa
    STACK == 0x3, 0x108, 0x15f, 0x0
    SCB count = 4
    Kernel NEXTQSCB = 2
    Card NEXTQSCB = 2
    QINFIFO entries:
    Waiting Queue entries:
    Disconnected Queue entries:
    QOUTFIFO entries:
    Sequencer Free SCB List: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
    19 20 21 22 23 24 25 26 27 28 29 30 31
    Pending list:
    Kernel Free SCB list: 3 1 0
    DevQ(0:0:0): 0 waiting
    scsi0:0:0:0: Command already completed
    aic7xxx_abort returns 8194
    scsi0:0:0:0: Attempting to queue an ABORT message
    (scsi0:A:0:0): Sending PPR bus_width 1, period c, offset 7f, ppr_options 0
    scsi0: Dumping Card State in Message-out phase, at SEQADDR 0x168
    SCSISEQ = 0x12, SBLKCTL = 0x6
    DFCNTRL = 0x0, DFSTATUS = 0x89
    LASTPHASE = 0xa0, SCSISIGI = 0xb6, SXFRCTL0 = 0x88
    SSTAT0 = 0x2, SSTAT1 = 0x3
    STACK == 0x175, 0x15f, 0x0, 0xe7
    SCB count = 4
    Kernel NEXTQSCB = 3
    Card NEXTQSCB = 3
    QINFIFO entries:
    Waiting Queue entries:
    Disconnected Queue entries:
    QOUTFIFO entries:
    Sequencer Free SCB List: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
    20 21 22 23 24 25 26 27 28 29 30 31
    Pending list: 2
    Kernel Free SCB list: 1 0
    Untagged Q(0): 2
    DevQ(0:0:0): 0 waiting
    scsi0:0:0:0: Device is active, asserting ATN
    Recovery code sleeping
    Recovery code awake
    Timer Expired
    aic7xxx_abort returns 8195
    scsi0:0:0:0: Attempting to queue a TARGET RESET message
    aic7xxx_dev_reset returns 8195
    Recovery SCB completes
    scsi0: SCSI bus reset delivered. 1 SCBs aborted.
    scsi0:0:0:0: Attempting to queue an ABORT message
    ahc_intr: HOST_MSG_LOOP bad phase 0x0
    scsi0: Dumping Card State in Message-out phase, at SEQADDR 0x45
    SCSISEQ = 0x12, SBLKCTL = 0x6
    DFCNTRL = 0x0, DFSTATUS = 0x89
    LASTPHASE = 0xa0, SCSISIGI = 0x0, SXFRCTL0 = 0x88
    SSTAT0 = 0x0, SSTAT1 = 0x0
    STACK == 0x15f, 0x0, 0xe6, 0x3
    SCB count = 4
    Kernel NEXTQSCB = 2
    Card NEXTQSCB = 3
    QINFIFO entries: 3
    Waiting Queue entries:
    Disconnected Queue entries:
    QOUTFIFO entries:
    Sequencer Free SCB List: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
    19 20 21 22 23 24 25 26 27 28 29 30 31
    Pending list: 3
    Kernel Free SCB list: 1 0
    Untagged Q(0): 3
    DevQ(0:0:0): 0 waiting
    scsi0:0:0:0: Cmd aborted from QINFIFO
    aic7xxx_abort returns 8194
    scsi: device set offline - not ready or command retry failed after bus
    reset: host 0 channel 0 id 0 lun 0

    (repeated for each ID on each channel)

    David


    -
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

    \
     
     \ /
      Last update: 2005-03-22 12:55    [W:0.027 / U:60.156 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site