lkml.org 
[lkml]   [2001]   [May]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRE: 8139too bug in 2.4.4 (2.4.3?) & VIA 686a

I've compiled 2.4.3mdk-25 source with Athlon optimizations, and the
problem still happens.

eth0 Link encap:Ethernet HWaddr FF:FF:FF:FF:FF:FF
inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:4294967221 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:11 Base address:0x9000

Look at the HWaddr. With default kernel (not compiled), I haven't this
problem and my ethernet card goes well and the HWaddr is: ·"HWaddr
00:E0:29:9A:CB:62 ". And I'm sure after reboot I *MUST* restore all the
values of my BIOS setup. Believe me, I know. :(


Here is the output of dmesg when loading the 81389too module:

Assertion failed! ioaddr != NULL,8139too.c,rtl8139_init_one,line=927
eth0: SMC1211TX EZCard 10/100 (RealTek RTL8139) at 0x9000,
ff:ff:ff:ff:ff:ff, IRQ 11
eth0: Identified 8139 chip type 'RTL-8139C'
eth0: Setting 100mbps half-duplex based on auto-negotiated partner ability
ffff.
"Assertion failed! ioaddr != NULL,8139too.c,rtl8139_init_one,line=927"?
What is this? Is this the cause of the bug?

Now the lspci -vv:

00:0c.0 Ethernet controller: Accton Technology Corporation SMC2-1211TX
(rev 10)
Subsystem: Accton Technology Corporation EN-1207D Fast Ethernet Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 9000 [size=256]
Region 1: Memory at da800000 (32-bit, non-prefetchable) [size=256]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
I hope these lines can help.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2005-03-22 12:52    [from the cache]
©2003-2014 Jasper Spaans. Advertise on this site