lkml.org 
[lkml]   [2001]   [Dec]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    SubjectPROBLEM: Kernel Oops on cat /proc/ioports
    From
    Date
    [1.] One line summary of the problem:    

    Running "cat /proc/ioports" causes a segfault and kernel oops.


    [2.] Full description of the problem/report:

    Running "cat /proc/ioports" may cause cat to segfault, and the kernel to
    Oops. It doesn't happen immediately after boot -- its required to run
    the kernel for some time (minimum two days for me), and make it do some
    work.


    [3.] Keywords (i.e., modules, networking, kernel):

    kernel, proc


    [4.] Kernel version (from /proc/version):

    Linux version 2.4.14 (root@clo002c.clobea.co.za)
    (gcc version 2.96 20000731 (Red Hat Linux 7.1 2.96-81))
    #3 SMP Mon Nov 12 15:34:14 SAST 2001


    [5.] Output of Oops.. message (if applicable) with symbolic information
    resolved (see Documentation/oops-tracing.txt)

    Unable to handle kernel paging request at virtual address f886bc55
    printing eip:
    c02a925b
    *pde = 37bb5067
    *pte = 00000000
    Oops: 0000
    CPU: 0
    EIP: 0010:[vsnprintf+523/1056] Not tainted
    EIP: 0010:[<c02a925b>] Not tainted
    EFLAGS: 00010297
    eax: f886bc55 ebx: d957f16c ecx: f886bc55 edx: fffffffe
    esi: ffffffff edi: e98ddec4 ebp: ffffffff esp: e98dde6c
    ds: 0018 es: 0018 ss: 0018
    Process cat (pid: 29869, stackpage=e98dd000)
    Stack: 00000000 ffffffff 0000000a d760e480 d957f15e 00000006 d9580000 c02a94a6
    d957f15e 26a80ea2 c02bd8a6 e98ddeb8 c02a94c4 d957f15e c02bd895 e98ddeb8
    c011dcfb d957f15e c02bd895 00003000 0000307f f886bc55 c2838478 d957f15e
    Call Trace: [vsprintf+22/32] [sprintf+20/32] [do_resource_list+75/128] [do_resource_list+107/128] [get_resource_list+66/96]
    Call Trace: [<c02a94a6>] [<c02a94c4>] [<c011dcfb>] [<c011dd1b>] [<c011dd72>]
    [ioports_read_proc+46/96] [proc_file_read+206/400] [sys_read+150/208] [sys_brk+186/240] [system_call+51/56]
    [<c0154eae>] [<c0152a3e>] [<c01368f6>] [<c0127caa>] [<c010712b>]
    Code: 80 38 00 74 07 40 4a 83 fa ff 75 f4 29 c8 f6 04 24 10 89 c6

    and ksymoops < oops:

    Warning (compare_maps): mismatch on symbol partition_name , ksyms_base
    says c0254350, System.map says c01560b0. Ignoring ksyms_base entry

    >>EIP; c02a925b <vsnprintf+20b/420> <=====
    Trace; c02a94a6 <vsprintf+16/20>
    Trace; c02a94c4 <sprintf+14/20>
    Trace; c011dcfb <do_resource_list+4b/80>
    Trace; c011dd1b <do_resource_list+6b/80>
    Trace; c011dd72 <get_resource_list+42/60>
    Trace; c0154eae <ioports_read_proc+2e/60>
    Trace; c0152a3e <proc_file_read+ce/190>
    Trace; c01368f6 <sys_read+96/d0>
    Trace; c0127caa <sys_brk+ba/f0>
    Trace; c010712b <system_call+33/38>
    Code; c02a925b <vsnprintf+20b/420>
    00000000 <_EIP>:
    Code; c02a925b <vsnprintf+20b/420> <=====
    0: 80 38 00 cmpb $0x0,(%eax) <=====
    Code; c02a925e <vsnprintf+20e/420>
    3: 74 07 je c <_EIP+0xc> c02a9267 <vsnprintf+217/420>
    Code; c02a9260 <vsnprintf+210/420>
    5: 40 inc %eax
    Code; c02a9261 <vsnprintf+211/420>
    6: 4a dec %edx
    Code; c02a9262 <vsnprintf+212/420>
    7: 83 fa ff cmp $0xffffffff,%edx
    Code; c02a9265 <vsnprintf+215/420>
    a: 75 f4 jne 0 <_EIP>
    Code; c02a9267 <vsnprintf+217/420>
    c: 29 c8 sub %ecx,%eax
    Code; c02a9269 <vsnprintf+219/420>
    e: f6 04 24 10 testb $0x10,(%esp,1)
    Code; c02a926d <vsnprintf+21d/420>
    12: 89 c6 mov %eax,%esi



    [6.] A small shell script or example program which triggers the
    problem (if possible)

    cat /proc/ioports


    [7.] Environment
    [7.1.] Software (add the output of the ver_linux script here)

    Linux clo002c.clobea.co.za 2.4.14 #3 SMP Mon Nov 12 15:34:14 SAST 2001 i686 unknown

    Gnu C 2.96
    Gnu make 3.79.1
    binutils 2.10.91.0.2
    util-linux 2.11b
    mount 2.11b
    modutils 2.4.2
    e2fsprogs 1.19
    PPP 2.4.0
    isdn4k-utils 3.1pre1
    Linux C Library 2.2.2
    Dynamic linker (ldd) 2.2.2
    Procps 2.0.7
    Net-tools 1.57
    Console-tools 0.3.3
    Sh-utils 2.0
    Modules Loaded cyclades eepro100


    [7.2.] Processor information (from /proc/cpuinfo):


    processor : 0
    vendor_id : GenuineIntel
    cpu family : 6
    model : 8
    model name : Pentium III (Coppermine)
    stepping : 10
    cpu MHz : 999.584
    cache size : 256 KB
    fdiv_bug : no
    hlt_bug : no
    f00f_bug : no
    coma_bug : no
    fpu : yes
    fpu_exception : yes
    cpuid level : 2
    wp : yes
    flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr sse
    bogomips : 1992.29

    processor : 1
    vendor_id : GenuineIntel
    cpu family : 6
    model : 8
    model name : Pentium III (Coppermine)
    stepping : 10
    cpu MHz : 999.584
    cache size : 256 KB
    fdiv_bug : no
    hlt_bug : no
    f00f_bug : no
    coma_bug : no
    fpu : yes
    fpu_exception : yes
    cpuid level : 2
    wp : yes
    flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr sse
    bogomips : 1998.84


    [7.3.] Module information (from /proc/modules):

    cyclades 147616 16 (autoclean)
    eepro100 16960 1 (autoclean)


    [7.4.] Loaded driver and hardware information (/proc/ioports, /proc/iomem)

    I can't add this :( It causes the oops.


    [7.5.] PCI information ('lspci -vvv' as root)

    00:00.0 Host bridge: ServerWorks CNB20LE (rev 06)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
    Latency: 32, cache line size 08

    00:00.1 Host bridge: ServerWorks CNB20LE (rev 06)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 32, cache line size 08

    00:07.0 Communication controller: Cyclades Corporation Cyclom_Y below first megabyte (rev 01)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 32
    Interrupt: pin A routed to IRQ 25
    Region 0: Memory at 61100000 (32-bit, non-prefetchable) [size=128]
    Region 1: I/O ports at 3000 [size=128]
    Region 2: Memory at 000dc000 (low-1M, non-prefetchable) [size=16K]
    Expansion ROM at 61120000 [disabled] [size=4K]

    00:0b.0 Ethernet controller: Intel Corporation 82557 [Ethernet Pro 100] (rev 08)
    Subsystem: Intel Corporation 82559 Fast Ethernet LAN on Motherboard
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
    Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 32 (2000ns min, 14000ns max), cache line size 08
    Interrupt: pin A routed to IRQ 17
    Region 0: Memory at 63200000 (32-bit, non-prefetchable) [size=4K]
    Region 1: I/O ports at 3800 [size=64]
    Region 2: Memory at 63300000 (32-bit, non-prefetchable) [size=1M]
    Expansion ROM at 63400000 [disabled] [size=1M]
    Capabilities: [dc] Power Management version 2
    Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
    Status: D0 PME-Enable- DSel=0 DScale=2 PME-

    00:0d.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 65) (prog-if 00 [VGA])
    Subsystem: ATI Technologies Inc: Unknown device 0008
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
    Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 32 (2000ns min), cache line size 08
    Interrupt: pin A routed to IRQ 16
    Region 0: Memory at 62000000 (32-bit, non-prefetchable) [size=16M]
    Region 1: I/O ports at 3400 [size=256]
    Region 2: Memory at 61400000 (32-bit, non-prefetchable) [size=4K]
    Expansion ROM at 61420000 [disabled] [size=128K]
    Capabilities: [5c] Power Management version 1
    Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-

    00:0f.0 ISA bridge: ServerWorks OSB4 (rev 50)
    Subsystem: ServerWorks OSB4
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0

    00:0f.1 IDE interface: ServerWorks: Unknown device 0211 (prog-if 8a [Master SecP PriP])
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 32
    Region 4: I/O ports at 30c0 [size=16]

    00:0f.2 USB Controller: ServerWorks: Unknown device 0220 (rev 04) (prog-if 10 [OHCI])
    Subsystem: ServerWorks: Unknown device 0220
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 32 (20000ns max), cache line size 08
    Interrupt: pin A routed to IRQ 15
    Region 0: Memory at 63f00000 (32-bit, non-prefetchable) [size=4K]

    01:03.0 SCSI storage controller: Adaptec 7899P (rev 01)
    Subsystem: Citicorp TTI: Unknown device 10e3
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
    Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 32 (10000ns min, 6250ns max), cache line size 08
    Interrupt: pin A routed to IRQ 19
    BIST result: 00
    Region 0: I/O ports at 5000 [disabled] [size=256]
    Region 1: Memory at 63c20000 (64-bit, non-prefetchable) [size=4K]
    Expansion ROM at 63c40000 [disabled] [size=128K]
    Capabilities: [dc] Power Management version 2
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-

    01:03.1 SCSI storage controller: Adaptec 7899P (rev 01)
    Subsystem: Citicorp TTI: Unknown device 10e3
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
    Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 32 (10000ns min, 6250ns max), cache line size 08
    Interrupt: pin B routed to IRQ 18
    BIST result: 00
    Region 0: I/O ports at 5400 [disabled] [size=256]
    Region 1: Memory at 63c21000 (64-bit, non-prefetchable) [size=4K]
    Expansion ROM at 63c60000 [disabled] [size=128K]
    Capabilities: [dc] Power Management version 2
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-

    01:06.0 PCI bridge: Intel Corporation: Unknown device 0962 (rev 02) (prog-if 00 [Normal decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 32, cache line size 08
    Bus: primary=01, secondary=02, subordinate=02, sec-latency=32
    I/O behind bridge: 0000f000-00000fff
    Memory behind bridge: fff00000-000fffff
    Prefetchable memory behind bridge: fff00000-000fffff
    BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-

    01:06.1 RAID bus controller: Mylex Corporation: Unknown device 0050 (rev 02)
    Subsystem: Mylex Corporation: Unknown device 0052
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B-
    Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 32, cache line size 08
    Interrupt: pin A routed to IRQ 20
    Region 0: Memory at 63e00000 (32-bit, prefetchable) [size=8K]
    Expansion ROM at 63c00000 [disabled] [size=32K]
    Capabilities: [80] Power Management version 2
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-


    [7.6.] SCSI information (from /proc/scsi/scsi)

    Attached devices:
    Host: scsi1 Channel: 00 Id: 05 Lun: 00
    Vendor: DEC Model: DLT2000 Rev: 8B37
    Type: Sequential-Access ANSI SCSI revision: 02


    [7.7.] Other information that might be relevant to the problem
    (please look in /proc and include all information that you
    think to be relevant):

    cat /proc/meminfo:
    total: used: free: shared: buffers: cached:
    Mem: 1582149632 1576222720 5926912 0 868352 706162688
    Swap: 271392768 15073280 256319488
    MemTotal: 1545068 kB
    MemFree: 5788 kB
    MemShared: 0 kB
    Buffers: 848 kB
    Cached: 685944 kB
    SwapCached: 3668 kB
    Active: 1145656 kB
    Inactive: 334440 kB
    HighTotal: 655296 kB
    HighFree: 2044 kB
    LowTotal: 889772 kB
    LowFree: 3744 kB
    SwapTotal: 265032 kB
    SwapFree: 250312 kB


    [X.] Other notes, patches, fixes, workarounds:

    I've had it with 2.4.12, 2.4.12-ac, and 2.4.14. I've tested the RAM
    with memtest86, and memtest, and haven't found a problem yet. Oddly
    enough I can run "cat /proc/ioports" right after the machine boots, but
    not after its done some work. The address listed in "Cannot handle
    kernel paging request" is always the same. Workaround: don't do that.


    Thank you
    --
    Berend De Schouwer

    -
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

    \
     
     \ /
      Last update: 2005-03-22 13:14    [W:0.043 / U:92.756 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site