lkml.org 
[lkml]   [2001]   [Nov]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    Date
    From
    SubjectRe: PCMCIA and APM/ACPI issue (xircom card problem)
    > > work..
    >
    > So basically, the problem exists when CONFIG_ACPI=y, right? Can you try to
    > boot the ACPI enabled kernel with acpi=off in the command line?

    okay one kernel with ACPI it doesn't work with ACPI off it does ...
    2.4.15-pre8

    > Which exact error do you get from lspci? Does it give the error on both
    > kernels?

    lspci without ACPI dumps out:
    pcilib: Cannot open /proc/bus/pci/02/00.1
    lspci: Unable to read 64 bytes of configuration space.

    same except 00.1 is 00.7 on the ACPI boot..

    I've attached a bootup with ACPI debug switched on there seems to be some
    issues but I've no idea what they mean..

    Regards,
    Dave.

    --
    David Airlie, Software Engineer
    http://www.skynet.ie/~airlied / airlied@skynet.ie
    pam_smb / Linux DecStation / Linux VAX / ILUG person

    Linux version 2.4.15-pre8-acpi (root@radon) (gcc version 2.95.2 19991024 (release)) #5 Thu Nov 22 14:17:05 GMT 2001
    BIOS-provided physical RAM map:
    BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
    BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
    BIOS-e820: 00000000000c0000 - 00000000000cc000 (reserved)
    BIOS-e820: 0000000000100000 - 0000000007fec000 (usable)
    BIOS-e820: 0000000007fec000 - 0000000007ff0000 (reserved)
    BIOS-e820: 00000000100a0000 - 0000000010100000 (reserved)
    BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
    On node 0 totalpages: 32748
    zone(0): 4096 pages.
    zone(1): 28652 pages.
    zone(2): 0 pages.
    Local APIC disabled by BIOS -- reenabling.
    Could not enable APIC!
    Kernel command line: BOOT_IMAGE=acpi ro root=306 vga=0x0301 noinitrd
    Initializing CPU#0
    Detected 430.142 MHz processor.
    Console: colour VGA+ 80x25
    Calibrating delay loop... 858.52 BogoMIPS
    Memory: 127064k/130992k available (841k kernel code, 3540k reserved, 236k data, 200k init, 0k highmem)
    Dentry-cache hash table entries: 16384 (order: 5, 131072 bytes)
    Inode-cache hash table entries: 8192 (order: 4, 65536 bytes)
    Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
    Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
    Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
    CPU: Before vendor init, caps: 0183f9ff 00000000 00000000, vendor = 0
    CPU: L1 I cache: 16K, L1 D cache: 16K
    CPU: L2 cache: 128K
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#0.
    CPU: After vendor init, caps: 0183f9ff 00000000 00000000 00000000
    CPU: After generic, caps: 0183f9ff 00000000 00000000 00000000
    CPU: Common caps: 0183f9ff 00000000 00000000 00000000
    CPU: Intel Celeron (Mendocino) stepping 0a
    Enabling fast FPU save and restore... done.
    Checking 'hlt' instruction... OK.
    POSIX conformance testing by UNIFIX
    mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
    mtrr: detected mtrr type: Intel
    PCI: PCI BIOS revision 2.10 entry at 0xfc0be, last bus=1
    PCI: Using configuration type 1
    PCI: Probing PCI hardware
    Unknown bridge resource 2: assuming transparent
    PCI: Using IRQ router PIIX [8086/7110] at 00:07.0
    Limiting direct PCI/PCI transfers.
    Linux NET4.0 for Linux 2.4
    Based upon Swansea University Computer Society NET3.039
    Starting kswapd
    devfs: v0.120 (20011103) Richard Gooch (rgooch@atnf.csiro.au)
    devfs: boot_options: 0x1
    tbxface-0099 [01] Acpi_load_tables : ACPI Tables successfully loaded
    Parsing Methods:........................................................................................................................................................
    152 Control Methods found and parsed (354 nodes total)
    ACPI Namespace successfully loaded at root c0252b20
    ACPI: Core Subsystem version [20011018]
    evxfevnt-0081 [02] Acpi_enable : Transition to ACPI mode successful
    Executing device _INI methods:.........Ps_execute: method failed - \_SB_.PCI0._INI (c7fa9f08)
    nsinit-0351 [04] Ns_init_one_device : \ /_SB_PCI0._INI failed: AE_AML_NOT_OWNER
    ..............Ps_execute: method failed - \_SB_.PCI0.PX40.FDC0._STA (c7fa6408)
    uteval-0337 [05] Ut_execute_STA : _STA on FDC0 failed AE_AML_NOT_OWNER
    ...Ps_execute: method failed - \_SB_.PCI0.PX40.UAR1._STA (c7fa5648)
    uteval-0337 [05] Ut_execute_STA : _STA on UAR1 failed AE_AML_NOT_OWNER
    .Ps_execute: method failed - \_SB_.PCI0.PX40.IRDA._STA (c7fa5ac8)
    uteval-0337 [05] Ut_execute_STA : _STA on IRDA failed AE_AML_NOT_OWNER
    .Ps_execute: method failed - \_SB_.PCI0.PX40.ECP_._STA (c7fa5ec8)
    uteval-0337 [05] Ut_execute_STA : _STA on ECP_ failed AE_AML_NOT_OWNER
    .......................
    51 Devices found: 47 _STA, 2 _INI
    Completing Region and Field initialization:..
    0/2 Regions, 2/10 Fields initialized (354 nodes total)
    ACPI: Subsystem enabled
    pty: 256 Unix98 ptys configured
    block: 128 slots per queue, batch=32
    Uniform Multi-Platform E-IDE driver Revision: 6.31
    ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    PIIX4: IDE controller on PCI bus 00 dev 39
    PIIX4: chipset revision 1
    PIIX4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x0860-0x0867, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0x0868-0x086f, BIOS settings: hdc:DMA, hdd:pio
    hda: FUJITSU MHH2064AT, ATA DISK drive
    hdc: TORiSAN DVD-ROM DRD-U624, ATAPI CD/DVD-ROM drive
    ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
    ide1 at 0x170-0x177,0x376 on irq 15
    hda: 12685680 sectors (6495 MB) w/512KiB Cache, CHS=789/255/63, UDMA(33)
    Partition check:
    /dev/ide/host0/bus0/target0/lun0: p1 p3 < p5 p6 >
    NET4: Linux TCP/IP 1.0 for NET4.0
    IP Protocols: ICMP, UDP, TCP
    IP: routing cache hash table of 512 buckets, 4Kbytes
    TCP: Hash tables configured (established 8192 bind 8192)
    NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
    VFS: Mounted root (ext2 filesystem) readonly.
    Mounted devfs on /dev
    Freeing unused kernel memory: 200k freed
    Adding Swap: 136512k swap-space (priority -1)
    usb.c: registered new driver usbdevfs
    usb.c: registered new driver hub
    usb-uhci.c: $Revision: 1.268 $ time 14:24:38 Nov 22 2001
    usb-uhci.c: High bandwidth mode enabled
    PCI: Found IRQ 11 for device 00:07.2
    PCI: Sharing IRQ 11 with 00:03.0
    PCI: Sharing IRQ 11 with 00:03.1
    usb-uhci.c: USB UHCI at I/O 0xdce0, IRQ 11
    usb-uhci.c: Detected 2 ports
    usb.c: new USB bus registered, assigned bus number 1
    usb.c: kmalloc IF c7cb9480, numif 1
    usb.c: new device strings: Mfr=0, Product=2, SerialNumber=1
    usb.c: USB device number 1 default language ID 0x0
    Product: USB UHCI Root Hub
    SerialNumber: dce0
    hub.c: USB hub found
    hub.c: 2 ports detected
    hub.c: standalone hub
    hub.c: ganged power switching
    hub.c: global over-current protection
    hub.c: Port indicators are not supported
    hub.c: power on to power good time: 2ms
    hub.c: hub controller current requirement: 0mA
    hub.c: port removable status: RR
    hub.c: local power source is good
    hub.c: no over-current condition exists
    hub.c: enabling power on all ports
    usb.c: hub driver claimed interface c7cb9480
    usb-uhci.c: v1.268:USB Universal Host Controller Interface driver
    Linux PCMCIA Card Services 3.1.29
    kernel build: 2.4.15-pre8-acpi #5 Thu Nov 22 14:17:05 GMT 2001
    options: [pci] [cardbus] [apm]
    Intel ISA/PCI/CardBus PCIC probe:
    PCI: Found IRQ 11 for device 00:03.0
    PCI: Sharing IRQ 11 with 00:03.1
    PCI: Sharing IRQ 11 with 00:07.2
    PCI: Found IRQ 11 for device 00:03.1
    PCI: Sharing IRQ 11 with 00:03.0
    PCI: Sharing IRQ 11 with 00:07.2
    TI 1225 rev 01 PCI-to-CardBus at slot 00:03, mem 0x10000000
    host opts [0]: [ring] [serial pci & irq] [pci irq 11] [lat 32/32] [bus 4/4]
    host opts [1]: [ring] [serial pci & irq] [pci irq 11] [lat 32/32] [bus 5/5]
    ISA irqs (scanned) = 3,4,7,10 PCI status changes
    cs: cb_alloc(bus 4): vendor 0xffff, device 0xffff
    apm: BIOS version 1.2 Flags 0x03 (Driver version 1.15)
    apm: overridden by ACPI.
    PCI: Found IRQ 5 for device 00:08.0
    maestro: Configuring ESS Maestro 2E found at IO 0xD800 IRQ 5
    maestro: subvendor id: 0x00ab1028
    maestro: PCI power management capability: 0x7622
    maestro: AC97 Codec detected: v: 0x83847609 caps: 0x6940 pwr: 0xf
    maestro: 1 channels configured.
    maestro: version 0.15 time 14:24:22 Nov 22 2001

    -
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

    \
     
     \ /
      Last update: 2005-03-22 13:13    [W:0.061 / U:32.000 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site