lkml.org 
[lkml]   [2000]   [Sep]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectPROBLEM: Xircom Realport gets MAC 00:00:00...... Card known good.
This is very verbose. Sorry. I much prefer to toss all the pieces on the
table at the same time.

Dag B

[1.] One line summary of the problem:
-test7/8 version of xircom_tulip_cb does not enable my Xircom Realport
(RBEM56G-100)

Nor any of the other kernels I have tried...


[2.] Full description of the problem/report:
My Xircom Realport (RBEM56G-100) is causing headaches. It works with
NT4/SP5 on my Dell CPi laptop, so the hardware is functional. (Tested
this morning. )
When loading the xircom_tulip_cb.c:v0.91 driver, things looks ok, until
you study the MAC address, which is all zeros. What follows is the
output from -test7 and test8:

-test7:
Linux PCMCIA Card Services 3.1.11
options: [pci] [cardbus] [pm]
Yenta IRQ list 0098, PCI irq11
Socket status: 30000006
Yenta IRQ list 0098, PCI irq11
Socket status: 30000020
devfs: v0.102 (20000622) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
kmem_create: Forcing size word alignment - nfs_fh
cs: cb_alloc(bus 4): vendor 0x115d, device 0x0003
PCI: Failed to allocate resource 1 for PCI device 115d:0003
PCI: Failed to allocate resource 2 for PCI device 115d:0003
PCI: Failed to allocate resource 6 for PCI device 115d:0003
PCI: Enabling device 04:00.0 (0000 -> 0003)
PCI: Failed to allocate resource 1 for PCI device 115d:0103
PCI: Failed to allocate resource 2 for PCI device 115d:0103
PCI: Failed to allocate resource 6 for PCI device 115d:0103
PCI: Enabling device 04:00.1 (0000 -> 0003)
[snip]
tulip_attach(04:00.0)
PCI: Setting latency timer of device 04:00.0 to 64
xircom_tulip_cb.c:v0.91 4/14/99 becker@cesdis.gsfc.nasa.gov (modified by
danilo@cs.uni-magdeburg.de for XIRCOM CBE, fixed by Doug Ledford)
eth1: Xircom Cardbus Adapter (DEC 21143 compatible mode) rev 3 at
0x1800, 00:00:00:00:00:00, IRQ 11.

-test8:
Linux PCMCIA Card Services 3.1.20
options: [pci] [cardbus] [pm]
Yenta IRQ list 0298, PCI irq11
Socket status: 30000006
devfs: v0.102 (20000622) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x2
kmem_create: Forcing size word alignment - nfs_fh
Yenta IRQ list 0298, PCI irq11
Socket status: 30000020
cs: cb_alloc(bus 4): vendor 0x115d, device 0x0003
PCI: Failed to allocate resource 1 for PCI device 115d:0003
PCI: Failed to allocate resource 2 for PCI device 115d:0003
PCI: Failed to allocate resource 6 for PCI device 115d:0003
PCI: Enabling device 04:00.0 (0000 -> 0003)
PCI: Failed to allocate resource 1 for PCI device 115d:0103
PCI: Failed to allocate resource 2 for PCI device 115d:0103
PCI: Failed to allocate resource 6 for PCI device 115d:0103
PCI: Enabling device 04:00.1 (0000 -> 0003)
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 204k freed
Warning: unable to open an initial console.
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x300-0x307 0x378-0x37f
0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
eth0: first available media type: MII
tulip_attach(04:00.0)
PCI: Setting latency timer of device 04:00.0 to 64
xircom_tulip_cb.c:v0.91 4/14/99 becker@cesdis.gsfc.nasa.gov (modified by
danilo@cs.uni-magdeburg.de for XIRCOM CBE, fixed by Doug Ledford)
eth1: Xircom Cardbus Adapter (DEC 21143 compatible mode) rev 3 at
0x1800, 00:00:00:00:00:00, IRQ 11.

I can use ifconfig to set a hw-address (does the card really support
this?), but if I try to set an IP-address, the system hangs hard.

Donald Becker's tulip-diag says:
dagblap:/tmp# ./tulip-diag -p 0x1800 -t 4 -ee
tulip-diag.c:v2.03 7/31/2000 Donald Becker (becker@scyld.com)
http://www.scyld.com/diag/index.html
Assuming a Digital DS21143 Tulip adapter at 0x1800.
Port selection is MII, half-duplex.
Transmit stopped, Receive stopped, half-duplex.
The Rx process state is 'Stopped'.
The Tx process state is 'Stopped'.
PCI bus error!: Parity Error.
The transmit threshold is 128.
The NWay status register is 000000c6.
EEPROM size is 8.
WARNING: The EEPROM is missing or erased!
This interface is missing the EEPROM.
This is likely the non-primary interface on a multiport board.
EEPROM contents:
ffff ffff ffff ffff ffff ffff ffff ffff
ffff ffff ffff ffff ffff ffff ffff ffff
ffff ffff ffff ffff ffff ffff ffff ffff
ffff ffff ffff ffff ffff ffff ffff ffff
ffff ffff ffff ffff ffff ffff ffff ffff
ffff ffff ffff ffff ffff ffff ffff ffff
ffff ffff ffff ffff ffff ffff ffff ffff
ffff ffff ffff ffff ffff ffff ffff ffff
ID block CRC 0xfa (vs. 0xff).
Full contents CRC 0x6a15 (read as 0xffff).
Internal autonegotiation state is 'Invalid state'.

This is a 10/100BaseTX/56K modem combo card. Loading serial_cb produces
nothing. And the card still works under that other OS...



[3.] Keywords (i.e., modules, networking, kernel):
Xircom, cardbus, xircom_tulip_cb, mac, hwaddress


[4.] Kernel version (from /proc/version):
2.4.0-test8 (gcc version 2.95.2 19991024 (release))

[5.] Output of Oops.. message (if applicable) with symbolic information
resolved (see Documentation/oops-tracing.txt)
[6.] A small shell script or example program which triggers the
problem (if possible)
[7.] Environment
[7.1.] Software (add the output of the ver_linux script here)
Linux dagblap 2.4.0-test8 #1 Mon Sep 11 21:36:49 CEST 2000 i686 unknown
Kernel modules 2.3.15
Gnu C 2.95.2
Binutils 2.10.0.24
Linux C Library 2.1.3
Dynamic linker ldd (GNU libc) 2.1.3
Procps 2.0.7
Mount 2.10o
Net-tools 1.57
Console-tools 0.2.3
Sh-utils 2.0
Modules Loaded xircom_tulip_cb


[7.2.] Processor information (from /proc/cpuinfo):
PII366

[7.3.] Module information (from /proc/modules):
xircom_tulip_cb

[7.4.] Loaded driver and hardware information (/proc/ioports,
/proc/iomem)
# cat /proc/ioports
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
02e8-02ef : serial(auto)
0376-0376 : ide1
03c0-03df : vesafb
03f6-03f6 : ide0
03f8-03ff : serial(auto)
0800-083f : Intel Corporation 82371AB PIIX4 ACPI
0840-085f : Intel Corporation 82371AB PIIX4 ACPI
0860-086f : Intel Corporation 82371AB PIIX4 IDE
0860-0867 : ide0
0868-086f : ide1
0cf8-0cff : PCI conf1
1000-10ff : PCI CardBus #02
1400-14ff : PCI CardBus #02
1800-18ff : PCI CardBus #04
1800-187f : PCI device 115d:0003
1800-187f : eth1
1880-1887 : PCI device 115d:0103
1c00-1cff : PCI CardBus #04
c000-cfff : PCI Bus #01
ec80-ecbf : 3Com Corporation 3c905 100BaseTX [Boomerang]
ec80-ecbf : eth0
ece0-ecff : Intel Corporation 82371AB PIIX4 USB

# cat /proc/iomem
00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000ce000-000ce7ff : Extension ROM
000ce800-000cefff : Extension ROM
000cf000-000cf7ff : Extension ROM
000cf800-000cffff : Extension ROM
000f0000-000fffff : System ROM
00100000-05feffff : System RAM
00100000-00272a67 : Kernel code
00272a68-0029a077 : Kernel data
05ff0000-05ffffff : ACPI Tables
10000000-10000fff : Texas Instruments PCI1225
10001000-10001fff : Texas Instruments PCI1225 (#2)
100a0000-100fffff : reserved
10400000-107fffff : PCI CardBus #02
10800000-10bfffff : PCI CardBus #02
10c00000-10ffffff : PCI CardBus #04
11000000-113fffff : PCI CardBus #04
f4000000-f7ffffff : Intel Corporation 440BX/ZX - 82443BX/ZX Host bridge
f9000000-fbffffff : PCI Bus #01
fac00000-faffffff : Neomagic Corporation [MagicMedia 256AV Audio]
fb000000-fbffffff : Neomagic Corporation [MagicMedia 256AV]
fb000000-fb25ffff : vesafb
fd000000-feffffff : PCI Bus #01
fda00000-fdafffff : Neomagic Corporation [MagicMedia 256AV Audio]
fdb00000-fdbfffff : Neomagic Corporation [MagicMedia 256AV]
fdc00000-fdffffff : Neomagic Corporation [MagicMedia 256AV]
ffe00000-ffffffff : reserved

[7.5.] PCI information ('lspci -vvv' as root)
You really want all that? :-)
# lspci -vvv
00:00.0 Host bridge: Intel Corporation 440BX/ZX - 82443BX/ZX Host bridge
(rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 32
Region 0: Memory at f4000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 1.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>

00:01.0 PCI bridge: Intel Corporation 440BX/ZX - 82443BX/ZX AGP bridge
(rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fd000000-feffffff
Prefetchable memory behind bridge: f9000000-fbffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B+

00:03.0 CardBus bridge: Texas Instruments PCI1225 (rev 01)
Subsystem: Dell Computer Corporation: Unknown device 0088
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 20
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 10000000 (32-bit, non-prefetchable)
[size=4K]
Bus: primary=00, secondary=02, subordinate=02, sec-latency=176
Memory window 0: 10400000-107ff000 (prefetchable)
Memory window 1: 10800000-10bff000
I/O window 0: 00001000-000010ff
I/O window 1: 00001400-000014ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+
PostWrite+
16-bit legacy interface ports at 0001

00:03.1 CardBus bridge: Texas Instruments PCI1225 (rev 01)
Subsystem: Dell Computer Corporation: Unknown device 0088
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 20
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 10001000 (32-bit, non-prefetchable)
[size=4K]
Bus: primary=00, secondary=04, subordinate=04, sec-latency=176
Memory window 0: 10c00000-10fff000 (prefetchable)
Memory window 1: 11000000-113ff000
I/O window 0: 00001800-000018ff
I/O window 1: 00001c00-00001cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt-
PostWrite+
16-bit legacy interface ports at 0001

00:07.0 Bridge: Intel Corporation 82371AB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0

00:07.1 IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 01)
(prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at 0860 [size=16]

00:07.2 USB Controller: Intel Corporation 82371AB PIIX4 USB (rev 01)
(prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at ece0 [size=32]

00:07.3 Bridge: Intel Corporation 82371AB PIIX4 ACPI (rev 02)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

00:0d.0 Ethernet controller: 3Com Corporation 3c905 100BaseTX
[Boomerang]
Subsystem: Dell Computer Corporation: Unknown device 0075
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (750ns min, 2000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at ec80 [size=64]
Expansion ROM at f3000000 [disabled] [size=64K]

01:00.0 VGA compatible controller: Neomagic Corporation [MagicMedia
256AV] (rev 20) (prog-if 00 [VGA])
Subsystem: Dell Computer Corporation: Unknown device 0088
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (4000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fb000000 (32-bit, prefetchable) [size=16M]
Region 1: Memory at fdc00000 (32-bit, non-prefetchable)
[size=4M]
Region 2: Memory at fdb00000 (32-bit, non-prefetchable)
[size=1M]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

01:00.1 Multimedia audio controller: Neomagic Corporation [MagicMedia
256AV Audio] (rev 20)
Subsystem: Dell Computer Corporation: Unknown device 0088
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 5
Region 0: Memory at fac00000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at fda00000 (32-bit, non-prefetchable)
[size=1M]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

04:00.0 Ethernet controller: Xircom Cardbus Ethernet 10/100 (rev 03)
Subsystem: Xircom Cardbus Ethernet 10/100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR+
Latency: 64 (5000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 1800 [size=128]
Region 1: [virtual] Memory at 11000000 (32-bit,
non-prefetchable) [size=4M]
Region 2: [virtual] Memory at 11000000 (32-bit,
non-prefetchable) [size=4M]
Expansion ROM at 11000000 [disabled] [size=4M]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-

04:00.1 VGA compatible controller: Xircom Cardbus Ethernet + 56k Modem
(rev 03) (prog-if 02)
Subsystem: Xircom CBEM56G-100 Ethernet + 56k Modem
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR+
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 1880 [size=8]
Region 1: [virtual] Memory at 11000000 (32-bit,
non-prefetchable) [size=4M]
Region 2: [virtual] Memory at 11000000 (32-bit,
non-prefetchable) [size=4M]
Expansion ROM at 11000000 [disabled] [size=4M]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-


[7.6.] SCSI information (from /proc/scsi/scsi)
[7.7.] Other information that might be relevant to the problem
(please look in /proc and include all information that you
think to be relevant):

# cat /proc/interrupts
CPU0
0: 141440 XT-PIC timer
1: 3 XT-PIC keyboard
2: 0 XT-PIC cascade
10: 1802 XT-PIC eth0
11: 0 XT-PIC Texas Instruments PCI1225, Texas
Instruments PCI1225 (#2)
12: 0 XT-PIC PS/2 Mouse
13: 0 XT-PIC fpu
14: 1166 XT-PIC ide0
15: 3 XT-PIC ide1
NMI: 0
ERR: 0

[X.] Other notes, patches, fixes, workarounds:
The BIOS rev. of this laptop is A09.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2005-03-22 12:38    [W:0.487 / U:0.148 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site