lkml.org 
[lkml]   [2000]   [Feb]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectNULL pointer dereference on boot 2.3.4[67]
Hello all...

I've run into the following problem in 2.3.46 and 2.3.47 where
I get an "Unable to handle kernel NULL pointer dereference" when booting
up. Any numbers are for my 2.3.47 build (I've already pitched the 2.3.46
and can't confirm that the numbers match). 2.3.45 boots and runs fine
and I used the 2.3.45 config file to build the new config file using
"make oldconfig".

When booting 2.3.47, I get to the point of ide detection. I
get the following normal messages just before the failure:

PIIX4: IDE controller on PCI Bus 00 dev 21
PIIX4: not 100% native mode: will probe irqs later
hdc: ATAPI 44X CDROM, ATAPI CDROM drive
ide1 at 0x170-0x177,0x376 on irq 15

I should see these messages next (taken from 2.3.45 bootup):

hdc: ATAPI 40X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.06

Instead I get:

Unable to handle kernel NULL pointer dereference at virtual address 00000267
printing eip:
c019a198
*pde=00000000
Oops: 0000

[...] (I can get the rest of the register dump if anyone needs it,
I just have to copy it down by hand)

The call traceback is:

[<c018f4fc>] [<c019a48b>] [<c019a56d>] [<c019a701>] [<c0105000>] [<c010709f>] [<c0107497>]

Related pieces of System.map:

[<c018f4fc>]
c018f4fc T do_ide1_request

[<c019a48b>]
[<c019a56d>]
c019a200 t hwif_init
c019a4f4 T ideprobe_init
c019a5a0 t put_cmd640_reg_pci1
c019a5e4 t get_cmd640_reg_pci1

[<c019a701>]
c019a6fc t match_pci_cmd640_device
c019a750 t probe_for_cmd640_pci1
c019a79c t probe_for_cmd640_pci2

[<c0105000>]
c0105000 T empty_bad_page

[<c010709f>]
c0107098 t init
c01071f0 T disable_hlt

[<c0107497>]
c0107474 T kernel_thread
c01074a4 T exit_thread


System Info:

CPU: Pentium III (Katmai)
Speed: 450 MHz
Mem: 256M
Distro: RedHat 6.1
gcc: gcc version egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)

Problem does not occur on 2.3.45 but does occur on 2.3.46 and 2.3.47
dependably.

This is also not occuring on another system of mine which is a
RedHat 5.2 system on a 350MHz AMD K6, which is running 2.3.47 just fine.

Gcc on the K6 system: gcc version 2.7.2.3

Other differences... The system which fails has no ide hard drives
and ide0 is disabled (CD-Rom is on ide1). The system which has not failed
does have an ide hard drive on ide0 and a CD-Rom drive on ide1.

I've also tried 586 and 686 builds. All fail (just with different
addresses).

Attached below is my .config file from this build.

I have not (yet) tried building the kernel for the P-III system
on the K6 system. If there is strong reason to suspect the compiler,
I will try that next.

Any other ideas or suggestions on what to try next?

Mike
--
Michael H. Warfield | (770) 985-6132 | mhw@WittsEnd.com
(The Mad Wizard) | (770) 331-2437 | http://www.wittsend.com/mhw/
NIC whois: MHW9 | An optimist believes we live in the best of all
PGP Key: 0xDF1DD471 | possible worlds. A pessimist is sure of it!

===== linux-2.3.47/.config =====
#
# Automatically generated make config: don't edit
#
CONFIG_X86=y
CONFIG_ISA=y
CONFIG_UID16=y

#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y

#
# Processor type and features
#
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
CONFIG_M686=y
# CONFIG_MK6 is not set
# CONFIG_MK7 is not set
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_TSC=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_PGE=y
# CONFIG_MICROCODE is not set
CONFIG_NOHIGHMEM=y
# CONFIG_HIGHMEM4G is not set
# CONFIG_HIGHMEM64G is not set
# CONFIG_MATH_EMULATION is not set
# CONFIG_MTRR is not set
# CONFIG_SMP is not set
# CONFIG_X86_UP_IOAPIC is not set

#
# Loadable module support
#
CONFIG_MODULES=y
# CONFIG_MODVERSIONS is not set
CONFIG_KMOD=y

#
# General setup
#
CONFIG_NET=y
# CONFIG_VISWS is not set
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_NAMES=y
# CONFIG_MCA is not set
# CONFIG_HOTPLUG is not set
CONFIG_SYSVIPC=y
# CONFIG_BSD_PROCESS_ACCT is not set
CONFIG_SYSCTL=y
CONFIG_KCORE_ELF=y
# CONFIG_KCORE_AOUT is not set
CONFIG_BINFMT_AOUT=y
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_MISC=y
CONFIG_PARPORT=y
CONFIG_PARPORT_PC=y
# CONFIG_PARPORT_PC_FIFO is not set
# CONFIG_PARPORT_AMIGA is not set
# CONFIG_PARPORT_MFC3 is not set
# CONFIG_PARPORT_ATARI is not set
# CONFIG_PARPORT_SUNBPP is not set
# CONFIG_PARPORT_OTHER is not set
# CONFIG_PARPORT_1284 is not set
# CONFIG_ACPI is not set
# CONFIG_APM is not set

#
# Plug and Play configuration
#
# CONFIG_PNP is not set
# CONFIG_ISAPNP is not set

#
# Block devices
#
CONFIG_BLK_DEV_FD=y
CONFIG_BLK_DEV_IDE=y

#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=y
# CONFIG_IDEDISK_MULTI_MODE is not set
CONFIG_BLK_DEV_IDECD=y
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
# CONFIG_BLK_DEV_IDESCSI is not set

#
# IDE chipset support/bugfixes
#
CONFIG_BLK_DEV_CMD640=y
# CONFIG_BLK_DEV_CMD640_ENHANCED is not set
CONFIG_BLK_DEV_RZ1000=y
CONFIG_BLK_DEV_IDEPCI=y
# CONFIG_BLK_DEV_IDEDMA_PCI is not set
# CONFIG_BLK_DEV_OFFBOARD is not set
# CONFIG_BLK_DEV_AEC6210 is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_IDE_CHIPSETS is not set
# CONFIG_BLK_CPQ_DA is not set

#
# Additional Block Devices
#
CONFIG_BLK_DEV_LOOP=y
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_MD is not set
CONFIG_BLK_DEV_RAM=m
# CONFIG_BLK_DEV_XD is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_PARIDE is not set
CONFIG_BLK_DEV_IDE_MODES=y
# CONFIG_BLK_DEV_HD is not set

#
# Networking options
#
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_NETLINK=y
CONFIG_RTNETLINK=y
CONFIG_NETLINK_DEV=y
CONFIG_NETFILTER=y
CONFIG_NETFILTER_DEBUG=y
CONFIG_FILTER=y
CONFIG_UNIX=y
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
# CONFIG_IP_PNP is not set
# CONFIG_IP_ROUTER is not set
CONFIG_NET_IPIP=m
CONFIG_NET_IPGRE=m
# CONFIG_NET_IPGRE_BROADCAST is not set
# CONFIG_IP_MROUTE is not set
CONFIG_IP_ALIAS=y
# CONFIG_ARPD is not set
CONFIG_SYN_COOKIES=y

#
# (it is safe to leave these untouched)
#
CONFIG_SKB_LARGE=y
CONFIG_IPV6=y
CONFIG_IPV6_EUI64=y
# CONFIG_IPV6_NO_PB is not set
# CONFIG_KHTTPD is not set
# CONFIG_ATM is not set

#
#
#
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_DECNET is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_BRIDGE is not set
# CONFIG_LLC is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_NET_FASTROUTE is not set
# CONFIG_NET_HW_FLOWCONTROL is not set

#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set

#
# Telephony Support
#
# CONFIG_PHONE is not set
# CONFIG_PHONE_IXJ is not set

#
# SCSI support
#
CONFIG_SCSI=y

#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
CONFIG_SD_EXTRA_DEVS=40
CONFIG_CHR_DEV_ST=y
CONFIG_ST_EXTRA_DEVS=2
CONFIG_BLK_DEV_SR=y
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_SR_EXTRA_DEVS=2
CONFIG_CHR_DEV_SG=y

#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
# CONFIG_SCSI_DEBUG_QUEUES is not set
CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_CONSTANTS=y
CONFIG_SCSI_LOGGING=y

#
# SCSI low-level drivers
#
# CONFIG_SCSI_7000FASST is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AHA152X is not set
# CONFIG_SCSI_AHA1542 is not set
# CONFIG_SCSI_AHA1740 is not set
CONFIG_SCSI_AIC7XXX=y
# CONFIG_AIC7XXX_TCQ_ON_BY_DEFAULT is not set
CONFIG_AIC7XXX_CMDS_PER_DEVICE=8
# CONFIG_AIC7XXX_PROC_STATS is not set
CONFIG_AIC7XXX_RESET_DELAY=15
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_IN2000 is not set
# CONFIG_SCSI_AM53C974 is not set
# CONFIG_SCSI_MEGARAID is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_DTC3280 is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_EATA_DMA is not set
# CONFIG_SCSI_EATA_PIO is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_GENERIC_NCR5380 is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_PPA is not set
# CONFIG_SCSI_IMM is not set
# CONFIG_SCSI_NCR53C406A is not set
# CONFIG_SCSI_SYM53C416 is not set
# CONFIG_SCSI_SIM710 is not set
# CONFIG_SCSI_NCR53C7xx is not set
# CONFIG_SCSI_NCR53C8XX is not set
# CONFIG_SCSI_SYM53C8XX is not set
# CONFIG_SCSI_PAS16 is not set
# CONFIG_SCSI_PCI2000 is not set
# CONFIG_SCSI_PCI2220I is not set
# CONFIG_SCSI_PSI240I is not set
# CONFIG_SCSI_QLOGIC_FAS is not set
# CONFIG_SCSI_QLOGIC_ISP is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_SEAGATE is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_T128 is not set
# CONFIG_SCSI_U14_34F is not set
# CONFIG_SCSI_ULTRASTOR is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set

#
# IEEE 1394 (FireWire) support
#
# CONFIG_IEEE1394 is not set

#
# I2O device support
#
# CONFIG_I2O is not set
# CONFIG_I2O_PCI is not set
# CONFIG_I2O_BLOCK is not set
# CONFIG_I2O_LAN is not set
# CONFIG_I2O_SCSI is not set
# CONFIG_I2O_PROC is not set

#
# Network device support
#
CONFIG_NETDEVICES=y

#
# ARCnet devices
#
# CONFIG_ARCNET is not set
# CONFIG_DUMMY is not set
# CONFIG_EQUALIZER is not set
# CONFIG_ETHERTAP is not set
# CONFIG_NET_SB1000 is not set

#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
CONFIG_NET_VENDOR_3COM=y
# CONFIG_EL1 is not set
# CONFIG_EL2 is not set
# CONFIG_ELPLUS is not set
# CONFIG_EL16 is not set
# CONFIG_EL3 is not set
# CONFIG_3C515 is not set
# CONFIG_VORTEX is not set
# CONFIG_LANCE is not set
# CONFIG_NET_VENDOR_SMC is not set
# CONFIG_NET_VENDOR_RACAL is not set
# CONFIG_AT1700 is not set
# CONFIG_DEPCA is not set
# CONFIG_NET_ISA is not set
CONFIG_NET_PCI=y
# CONFIG_PCNET32 is not set
# CONFIG_ADAPTEC_STARFIRE is not set
# CONFIG_AC3200 is not set
# CONFIG_APRICOT is not set
# CONFIG_DE4X5 is not set
# CONFIG_TULIP is not set
# CONFIG_DGRS is not set
# CONFIG_DM9102 is not set
# CONFIG_EEPRO100 is not set
# CONFIG_LNE390 is not set
# CONFIG_NE3210 is not set
# CONFIG_NE2K_PCI is not set
# CONFIG_RTL8129 is not set
# CONFIG_8139TOO is not set
# CONFIG_SIS900 is not set
# CONFIG_TLAN is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_ES3210 is not set
# CONFIG_EPIC100 is not set
# CONFIG_NET_POCKET is not set

#
# Ethernet (1000 Mbit)
#
# CONFIG_YELLOWFIN is not set
# CONFIG_ACENIC is not set
# CONFIG_SK98LIN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PLIP is not set
CONFIG_PPP=m
CONFIG_PPP_ASYNC=m
# CONFIG_PPP_SYNC_TTY is not set
CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
# CONFIG_SLIP is not set

#
# Wireless LAN (non-hamradio)
#
# CONFIG_NET_RADIO is not set

#
# Token Ring driver support
#
# CONFIG_TR is not set
# CONFIG_NET_FC is not set
# CONFIG_RCPCI is not set
# CONFIG_SHAPER is not set

#
# Wan interfaces
#
# CONFIG_WAN is not set

#
# Amateur Radio support
#
# CONFIG_HAMRADIO is not set

#
# IrDA (infrared) support
#
# CONFIG_IRDA is not set

#
# ISDN subsystem
#
# CONFIG_ISDN is not set

#
# Old CD-ROM drivers (not SCSI, not IDE)
#
# CONFIG_CD_NO_IDESCSI is not set

#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_SERIAL=y
# CONFIG_SERIAL_CONSOLE is not set
# CONFIG_SERIAL_EXTENDED is not set
CONFIG_SERIAL_NONSTANDARD=y
CONFIG_COMPUTONE=m
# CONFIG_ROCKETPORT is not set
# CONFIG_CYCLADES is not set
# CONFIG_DIGIEPCA is not set
# CONFIG_DIGI is not set
# CONFIG_ESPSERIAL is not set
# CONFIG_MOXA_INTELLIO is not set
# CONFIG_MOXA_SMARTIO is not set
# CONFIG_ISI is not set
# CONFIG_SYNCLINK is not set
# CONFIG_N_HDLC is not set
# CONFIG_RISCOM8 is not set
# CONFIG_SPECIALIX is not set
# CONFIG_SX is not set
# CONFIG_STALDRV is not set
CONFIG_UNIX98_PTYS=y
CONFIG_UNIX98_PTY_COUNT=256
CONFIG_PRINTER=y
# CONFIG_LP_CONSOLE is not set
# CONFIG_PPDEV is not set

#
# I2C support
#
CONFIG_I2C=y
CONFIG_I2C_ALGOBIT=m
# CONFIG_I2C_PHILIPSPAR is not set
# CONFIG_I2C_ELV is not set
# CONFIG_I2C_VELLEMAN is not set
# CONFIG_I2C_ALGOPCF is not set
CONFIG_I2C_CHARDEV=m

#
# Mice
#
# CONFIG_BUSMOUSE is not set
CONFIG_MOUSE=y
CONFIG_PSMOUSE=y
# CONFIG_82C710_MOUSE is not set
# CONFIG_PC110_PAD is not set

#
# Joysticks
#
CONFIG_JOYSTICK=m
CONFIG_JOY_ANALOG=m
# CONFIG_JOY_ASSASSIN is not set
# CONFIG_JOY_GRAVIS is not set
# CONFIG_JOY_LOGITECH is not set
# CONFIG_JOY_SIDEWINDER is not set
# CONFIG_JOY_THRUSTMASTER is not set
# CONFIG_JOY_CREATIVE is not set
# CONFIG_JOY_LIGHTNING is not set
# CONFIG_JOY_PCI is not set
# CONFIG_JOY_MAGELLAN is not set
# CONFIG_JOY_SPACEORB is not set
# CONFIG_JOY_SPACEBALL is not set
# CONFIG_JOY_WARRIOR is not set
# CONFIG_JOY_CONSOLE is not set
# CONFIG_JOY_DB9 is not set
# CONFIG_JOY_TURBOGRAFX is not set
CONFIG_QIC02_TAPE=m
CONFIG_QIC02_DYNCONF=y

#
# Setting runtime QIC-02 configuration is done with qic02conf
#

#
# from the tpqic02-support package. It is available at
#

#
# metalab.unc.edu or ftp://titus.cfw.com/pub/Linux/util/
#

#
# Watchdog Cards
#
CONFIG_WATCHDOG=y
# CONFIG_WATCHDOG_NOWAYOUT is not set
# CONFIG_WDT is not set
CONFIG_SOFT_WATCHDOG=y
# CONFIG_PCWATCHDOG is not set
# CONFIG_ACQUIRE_WDT is not set
# CONFIG_MIXCOMWD is not set
CONFIG_NVRAM=y
CONFIG_RTC=y

#
# Video For Linux
#
CONFIG_VIDEO_DEV=m
# CONFIG_I2C_PARPORT is not set

#
# Radio Adapters
#
# CONFIG_RADIO_CADET is not set
# CONFIG_RADIO_RTRACK is not set
# CONFIG_RADIO_RTRACK2 is not set
# CONFIG_RADIO_AZTECH is not set
# CONFIG_RADIO_GEMTEK is not set
# CONFIG_RADIO_MIROPCM20 is not set
# CONFIG_RADIO_SF16FMI is not set
# CONFIG_RADIO_TERRATEC is not set
# CONFIG_RADIO_TRUST is not set
# CONFIG_RADIO_TYPHOON is not set
# CONFIG_RADIO_ZOLTRIX is not set

#
# Video Adapters
#
CONFIG_VIDEO_BT848=m
# CONFIG_VIDEO_PMS is not set
# CONFIG_VIDEO_BWQCAM is not set
# CONFIG_VIDEO_CQCAM is not set
# CONFIG_VIDEO_SAA5249 is not set
# CONFIG_VIDEO_STRADIS is not set
# CONFIG_VIDEO_ZORAN is not set
# CONFIG_VIDEO_BUZ is not set
# CONFIG_VIDEO_ZR36120 is not set
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set

#
# Ftape, the floppy tape device driver
#
# CONFIG_FTAPE is not set
# CONFIG_DRM is not set
# CONFIG_DRM_TDFX is not set
# CONFIG_AGP is not set

#
# USB support
#
CONFIG_USB=m

#
# USB Controllers
#
CONFIG_USB_UHCI=m
# CONFIG_USB_UHCI_HIGH_BANDWIDTH is not set
CONFIG_USB_UHCI_ALT=m
# CONFIG_USB_UHCI_ALT_UNLINK_OPTIMIZE is not set
CONFIG_USB_OHCI=m

#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y

#
# USB Devices
#
CONFIG_USB_PRINTER=m
CONFIG_USB_SCANNER=m
CONFIG_USB_AUDIO=m
CONFIG_USB_ACM=m
CONFIG_USB_SERIAL=m
CONFIG_USB_SERIAL_GENERIC=y
# CONFIG_USB_SERIAL_VISOR is not set
# CONFIG_USB_SERIAL_WHITEHEAT is not set
# CONFIG_USB_SERIAL_FTDI_SIO is not set
# CONFIG_USB_SERIAL_KEYSPAN_PDA is not set
# CONFIG_USB_CPIA is not set
# CONFIG_USB_IBMCAM is not set
# CONFIG_USB_OV511 is not set
# CONFIG_USB_DC2XX is not set
CONFIG_USB_STORAGE=m
# CONFIG_USB_STORAGE_DEBUG is not set
# CONFIG_USB_USS720 is not set
# CONFIG_USB_DABUSB is not set
# CONFIG_USB_PLUSB is not set

#
# USB HID
#
CONFIG_USB_HID=m
# CONFIG_USB_KBD is not set
# CONFIG_USB_MOUSE is not set
CONFIG_USB_GRAPHIRE=m
CONFIG_USB_WMFORCE=m
CONFIG_INPUT_KEYBDEV=m
CONFIG_INPUT_MOUSEDEV=m
CONFIG_INPUT_MOUSEDEV_MIX=y
# CONFIG_INPUT_MOUSEDEV_DIGITIZER is not set
CONFIG_INPUT_JOYDEV=m
# CONFIG_INPUT_EVDEV is not set

#
# Misc devices
#

#
# File systems
#
CONFIG_QUOTA=y
CONFIG_AUTOFS_FS=y
CONFIG_AUTOFS4_FS=y
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_BFS_FS is not set
CONFIG_FAT_FS=y
CONFIG_MSDOS_FS=y
# CONFIG_UMSDOS_FS is not set
CONFIG_VFAT_FS=y
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_MINIX_FS=m
CONFIG_NTFS_FS=m
# CONFIG_NTFS_RW is not set
# CONFIG_HPFS_FS is not set
CONFIG_PROC_FS=y
# CONFIG_DEVFS_FS is not set
# CONFIG_DEVFS_DEBUG is not set
CONFIG_DEVPTS_FS=y
# CONFIG_QNX4FS_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_EXT2_FS=y
# CONFIG_SYSV_FS is not set
CONFIG_UDF_FS=y
CONFIG_UDF_RW=y
# CONFIG_UFS_FS is not set

#
# Network File Systems
#
CONFIG_CODA_FS=m
CONFIG_NFS_FS=y
# CONFIG_ROOT_NFS is not set
CONFIG_NFSD=y
# CONFIG_NFSD_V3 is not set
CONFIG_SUNRPC=y
CONFIG_LOCKD=y
CONFIG_SMB_FS=y
# CONFIG_NCP_FS is not set

#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
CONFIG_NLS=y

#
# Native Language Support
#
CONFIG_NLS_CODEPAGE_437=y
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
# CONFIG_NLS_CODEPAGE_850 is not set
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_1 is not set
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_14 is not set
# CONFIG_NLS_ISO8859_15 is not set
# CONFIG_NLS_KOI8_R is not set

#
# Console drivers
#
CONFIG_VGA_CONSOLE=y
CONFIG_VIDEO_SELECT=y
# CONFIG_MDA_CONSOLE is not set

#
# Frame-buffer support
#
# CONFIG_FB is not set

#
# Sound
#
CONFIG_SOUND=m
# CONFIG_SOUND_CMPCI is not set
# CONFIG_SOUND_ES1370 is not set
# CONFIG_SOUND_ES1371 is not set
# CONFIG_SOUND_ESSSOLO1 is not set
# CONFIG_SOUND_MAESTRO is not set
# CONFIG_SOUND_SONICVIBES is not set
# CONFIG_SOUND_TRIDENT is not set
# CONFIG_SOUND_MSNDCLAS is not set
# CONFIG_SOUND_MSNDPIN is not set
CONFIG_SOUND_OSS=m
# CONFIG_SOUND_AD1816 is not set
# CONFIG_SOUND_SGALAXY is not set
# CONFIG_SOUND_CS4232 is not set
# CONFIG_SOUND_SSCAPE is not set
# CONFIG_SOUND_GUS is not set
# CONFIG_SOUND_VMIDI is not set
# CONFIG_SOUND_TRIX is not set
CONFIG_SOUND_MSS=m
CONFIG_SOUND_MPU401=m
# CONFIG_SOUND_NM256 is not set
# CONFIG_SOUND_MAD16 is not set
# CONFIG_SOUND_PAS is not set
# CONFIG_SOUND_PSS is not set
# CONFIG_SOUND_SOFTOSS is not set
CONFIG_SOUND_SB=m
# CONFIG_SOUND_WAVEFRONT is not set
# CONFIG_SOUND_MAUI is not set
# CONFIG_SOUND_VIA82CXXX is not set
# CONFIG_SOUND_YM3812 is not set
# CONFIG_SOUND_OPL3SA1 is not set
# CONFIG_SOUND_OPL3SA2 is not set
# CONFIG_SOUND_UART6850 is not set

#
# Additional low level sound drivers
#
# CONFIG_LOWLEVEL_SOUND is not set

#
# Kernel hacking
#
# CONFIG_MAGIC_SYSRQ is not set

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.rutgers.edu
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2005-03-22 13:56    [W:0.047 / U:0.840 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site