lkml.org 
[lkml]   [2000]   [Feb]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRunlevel at boot prompt doesn't work with BusLogic command in "append"
Hi.

I recently added an additional command to my "append" field in
lilo.conf, and it causes the kernel to not recognize the run level
parameter at the boot prompt anymore. In other words, if I type "linux
1" at the LILO: prompt, or "linux 2" or "linux 3", etc, I still go to
the run level defined in the inittab. I made another entry in lilo.conf
without the extra "append" command, and the run level works as it
should.

Any help is appreciated.


Here's the relevant parts of lilo.conf:
boot=/dev/hda
linear
disk=/dev/sda
bios=0x81
disk=/dev/sdb
bios=0x82
map=/boot/map
install=/boot/boot.b
prompt
timeout=50
default=linux

image=/boot/vmlinuz-2.2.14.3
label=linux
read-only
root=/dev/sda2
append="hdc=ide-scsi hdd=ide-scsi BusLogic=QD:[64,,,,64]"
image=/boot/vmlinuz-2.2.14.3
label=linux-work
read-only
root=/dev/sda2
append="hdc=ide-scsi hdd=ide-scsi"
image=... (other images, etc)


The "linux" label doesn't allow initial runlevel to be set at the
LILO prompt, but "linux-work" does. Other than the BusLogic command,
the two are identical.

Here's .config from /usr/src/linux:

CONFIG_EXPERIMENTAL=y
CONFIG_M686=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_TSC=y
CONFIG_X86_GOOD_APIC=y
CONFIG_1GB=y
CONFIG_MTRR=y
CONFIG_SMP=y
CONFIG_MODULES=y
CONFIG_KMOD=y
CONFIG_NET=y
CONFIG_PCI=y
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_QUIRKS=y
CONFIG_PCI_OLD_PROC=y
CONFIG_X86_IO_APIC=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_SYSVIPC=y
CONFIG_SYSCTL=y
CONFIG_BINFMT_AOUT=y
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_MISC=y
CONFIG_PARPORT=m
CONFIG_PARPORT_PC=m
CONFIG_APM=y
CONFIG_APM_POWER_OFF=y
CONFIG_BLK_DEV_FD=y
CONFIG_BLK_DEV_IDE=y
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_BLK_DEV_IDECD=y
CONFIG_BLK_DEV_IDESCSI=y
CONFIG_BLK_DEV_CMD640=y
CONFIG_BLK_DEV_RZ1000=y
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_BLK_DEV_IDEDMA=y
CONFIG_IDEDMA_AUTO=y
CONFIG_BLK_DEV_LOOP=m
CONFIG_BLK_DEV_NBD=m
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_INITRD=y
CONFIG_PARIDE_PARPORT=m
CONFIG_PACKET=y
CONFIG_UNIX=y
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_SKB_LARGE=y
CONFIG_SCSI=y
CONFIG_BLK_DEV_SD=y
CONFIG_BLK_DEV_SR=m
CONFIG_CHR_DEV_SG=m
CONFIG_SCSI_AIC7XXX=y
CONFIG_AIC7XXX_TCQ_ON_BY_DEFAULT=y
CONFIG_AIC7XXX_CMDS_PER_DEVICE=120
CONFIG_AIC7XXX_RESET_DELAY=5
CONFIG_SCSI_BUSLOGIC=y
CONFIG_NETDEVICES=y
CONFIG_DUMMY=y
CONFIG_NET_ETHERNET=y
CONFIG_NET_ISA=y
CONFIG_NET_EISA=y
CONFIG_NE2K_PCI=y
CONFIG_PPP=m
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_SERIAL=y
CONFIG_UNIX98_PTYS=y
CONFIG_UNIX98_PTY_COUNT=256
CONFIG_PRINTER=m
CONFIG_MOUSE=y
CONFIG_PSMOUSE=y
CONFIG_RTC=y
CONFIG_AUTOFS_FS=y
CONFIG_FAT_FS=m
CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
CONFIG_ISO9660_FS=m
CONFIG_JOLIET=y
CONFIG_MINIX_FS=m
CONFIG_NTFS_FS=m
CONFIG_PROC_FS=y
CONFIG_DEVPTS_FS=y
CONFIG_EXT2_FS=y
CONFIG_REISERFS_FS=y
CONFIG_CRYPTO_SECURE_HASH=y
CONFIG_NFS_FS=y
CONFIG_NFSD=y
CONFIG_SUNRPC=y
CONFIG_LOCKD=y
CONFIG_NLS=y
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_ISO8859_1=y
CONFIG_VGA_CONSOLE=y
CONFIG_SOUND=m
CONFIG_SOUND_OSS=m
CONFIG_SOUND_SB=m
CONFIG_SOUND_SOFTOSS=m
CONFIG_LOWLEVEL_SOUND=y
CONFIG_AWE32_SYNTH=m


--


-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.rutgers.edu
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2005-03-22 13:56    [W:0.037 / U:0.452 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site