Messages in this thread | | | Date | Mon, 06 Sep 1999 20:03:31 +0200 | From | Grégoire FAVRE <> | Subject | Re: 2.3.16 problem and P2B-LS |
| |
Grégoire FAVRE wrote: > > Hello, > > I have booted 2.3.16 with vga=normal and found the problem (2.3.13 and 2.3.15 also > don't boot normal, but I didn't see anything, as I used vga=794 and nothing print). > > At boot: > > Partition check: > sda: sda1 sda2 < sda5 > > sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 sdb6 sdb7 sdb8 sdb9 sdb10 > > Found PIIX4 ACPI device at e400 > scsi: aborting command due to timeout : pid 36, scsi 0, channel 0, id 4, lun 0 0 > x28 00 00 70 84 4c 00 00 02 00 > SCSI host 0 abort (pid 36) timeout - reseting > SCSI bus is being reset for host 0 channel 0. > SCSI ... reseted... > SCSI ... > > ad nauseam... > > The drive four is ultra2wide..., from 2.2.12: > > (scsi0) <Adaptec AIC-7890/1 Ultra2 SCSI host adapter> found at PCI 6/0 > (scsi0) Wide Channel, SCSI ID=7, 32/255 SCBs > (scsi0) Downloading sequencer code... 374 instructions downloaded > scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.19/3.2.4 > <Adaptec AIC-7890/1 Ultra2 SCSI host adapter> > scsi : 1 host. > (scsi0:0:0:0) Synchronous at 20.0 Mbyte/sec, offset 15. > Vendor: QUANTUM Model: FIREBALL_TM3200S Rev: 300X > Type: Direct-Access ANSI SCSI revision: 02 > Detected scsi disk sda at scsi0, channel 0, id 0, lun 0 > (scsi0:0:1:0) Synchronous at 20.0 Mbyte/sec, offset 8. > Vendor: PIONEER Model: DVD-ROM DVD-303 Rev: 1.09 > Type: CD-ROM ANSI SCSI revision: 02 > Detected scsi CD-ROM sr0 at scsi0, channel 0, id 1, lun 0 > (scsi0:0:2:0) Synchronous at 16.0 Mbyte/sec, offset 16. > Vendor: PIONEER Model: CD-ROM DR-U06S Rev: 1.05 > Type: CD-ROM ANSI SCSI revision: 02 > Detected scsi CD-ROM sr1 at scsi0, channel 0, id 2, lun 0 > (scsi0:0:3:0) Synchronous at 10.0 Mbyte/sec, offset 8. > Vendor: PLEXTOR Model: CD-R PX-R820T Rev: 1.05 > Type: CD-ROM ANSI SCSI revision: 02 > Detected scsi CD-ROM sr2 at scsi0, channel 0, id 3, lun 0 > (scsi0:0:4:0) Synchronous at 80.0 Mbyte/sec, offset 15. > Vendor: IBM Model: DDRS-39130D Rev: DC1B > Type: Direct-Access ANSI SCSI revision: 02 > Detected scsi disk sdb at scsi0, channel 0, id 4, lun 0 > scsi : detected 3 SCSI cdroms 2 SCSI disks total. > sr0: scsi3-mmc drive: 0x/0x cd/rw xa/form2 cdda tray > Uniform CDROM driver Revision: 2.55 > sr1: scsi3-mmc drive: 32x/32x cd/rw xa/form2 cdda tray > sr2: scsi3-mmc drive: 20x/20x writer cd/rw xa/form2 cdda tray > SCSI device sda: hdwr sector= 512 bytes. Sectors= 6281856 [3067 MB] [3.1 GB] > SCSI device sdb: hdwr sector= 512 bytes. Sectors= 17850000 [8715 MB] [8.7 GB] > PCI latency timer (CFLT) is unreasonably low at 0. Setting to 32 clocks. > eth0: Intel EtherExpress Pro 10/100 at 0xa800, 00:E0:18:90:14:C5, IRQ 14. > Board assembly 668081-002, Physical connectors present: RJ45 > Primary interface chip i82555 PHY #1. > General self-test: passed. > Serial sub-system self-test: passed. > Internal registers self-test: passed. > ROM checksum self-test: passed (0x24c9f043). > Receiver lock-up workaround activated. > Partition check: > sda: sda1 sda2 < sda5 > > sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 sdb6 sdb7 sdb8 sdb9 sdb10 > > VFS: Mounted root (ext2 filesystem) readonly. > > And my system is RedHat 6.0.
Disabling ACPI allow me to boot (paartially: vesafb won't work...).
Please, don't cc to me: I am on the list... Greg ICQ:16624071 mailto:greg@imaux.unil.ch '''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''' Gregoire Favre, Institut de Mathématique de l'Universite de Lausanne +41216923573,+41763231357, http://www.unil.ch/ima/docs/Personnes/gfavre
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.rutgers.edu Please read the FAQ at http://www.tux.org/lkml/
| |