Messages in this thread |  | | | From | "Allison, Bob" <> | | Subject | Linux 2.2.0-pre6 Success | | Date | Tue, 12 Jan 1999 00:48:02 -0500 |
| |
Since I don't see many reports of success, I thought I would give one.
I compiled 2.2.0-pre6 this evening, and found it to work OK: -- I can mount my FAT32 partition -- My SCSI devices are detected properly (see below)
I still need to boot my router on this release to make sure the firewall code is working correctly. I also do not have a lot of sound-related software yet, so I can't verify that my GUS MAX is working OK.
------------------------------------ dmesg bits of interest (from my P-120 desktop machine):
Linux version 2.2.0-pre6 (root@bob.home.net) (gcc version 2.7.2.3) #1 Mon Jan 11 17:59:40 EST 1999 Detected 118953081 Hz processor. Console: colour VGA+ 80x25 Calibrating delay loop... 47.41 BogoMIPS Memory: 63296k/65536k available (824k kernel code, 412k reserved, 972k data, 32k init) . . (scsi0) <Adaptec AHA-294X Ultra SCSI host adapter> found at PCI 18/0 (scsi0) Wide Channel, SCSI ID=7, 16/255 SCBs (scsi0) Warning - detected auto-termination (scsi0) Please verify driver detected settings are correct. (scsi0) If not, then please properly set the device termination (scsi0) in the Adaptec SCSI BIOS by hitting CTRL-A when prompted (scsi0) during machine bootup. (scsi0) Cables present (Int-50 YES, Int-68 NO, Ext-68 YES) (scsi0) Downloading sequencer code... 419 instructions downloaded (scsi1) <Adaptec AHA-2944 Ultra SCSI host adapter> found at PCI 19/0 (scsi1) Wide Channel, SCSI ID=7, 16/255 SCBs (scsi1) Warning - detected auto-termination (scsi1) Please verify driver detected settings are correct. (scsi1) If not, then please properly set the device termination (scsi1) in the Adaptec SCSI BIOS by hitting CTRL-A when prompted (scsi1) during machine bootup. (scsi1) Cables present (Int-50 NO, Int-68 NO, Ext-68 YES) (scsi1) Downloading sequencer code... 419 instructions downloaded scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.9/3.2.4 <Adaptec AHA-294X Ultra SCSI host adapter> scsi1 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.9/3.2.4 <Adaptec AHA-2944 Ultra SCSI host adapter> scsi : 2 hosts. Vendor: QUANTUM Model: FIREBALL_TM3200S Rev: 300X Type: Direct-Access ANSI SCSI revision: 02 Detected scsi disk sda at scsi0, channel 0, id 0, lun 0 (scsi0:0:0:0) Synchronous at 20.0 Mbyte/sec, offset 15. Vendor: HP Model: C2490AM Rev: 3256 Type: Direct-Access ANSI SCSI revision: 02 Detected scsi disk sdb at scsi0, channel 0, id 1, lun 0 (scsi0:0:1:0) Synchronous at 10.0 Mbyte/sec, offset 8. Vendor: HP Model: C1533A Rev: AN01 Type: Sequential-Access ANSI SCSI revision: 02 Detected scsi tape st0 at scsi0, channel 0, id 4, lun 0 (scsi0:0:4:0) Synchronous at 10.0 Mbyte/sec, offset 15. Vendor: TOSHIBA Model: CD-ROM XM-5701TA Rev: 0787 Type: CD-ROM ANSI SCSI revision: 02 Detected scsi CD-ROM sr0 at scsi0, channel 0, id 6, lun 0 (scsi0:0:6:0) Synchronous at 10.0 Mbyte/sec, offset 8. Vendor: DGC Model: C1300WDR0 Rev: HP01 Type: Direct-Access ANSI SCSI revision: 02 Detected scsi disk sdc at scsi1, channel 0, id 11, lun 0 (scsi1:0:11:0) Synchronous at 20.0 Mbyte/sec, offset 8. Vendor: DGC Model: C1300WDR0 Rev: HP01 Type: Direct-Access ANSI SCSI revision: 02 Detected scsi disk sdd at scsi1, channel 0, id 11, lun 1 Vendor: DGC Model: C1300WDR0 Rev: HP01 Type: Direct-Access ANSI SCSI revision: 02 Detected scsi disk sde at scsi1, channel 0, id 12, lun 0 (scsi1:0:12:0) Synchronous at 20.0 Mbyte/sec, offset 8. scsi : detected 1 SCSI tape 1 SCSI cdrom 5 SCSI disks total. . . ad1848/cs4248 codec driver Copyright (C) by Hannu Savolainen 1993-1996 Gravis Ultrasound audio driver Copyright (C) by Hannu Savolainen 1993-1996
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.rutgers.edu Please read the FAQ at http://www.tux.org/lkml/
|  |