Messages in this thread |  | | | Subject | alpha PC164 w/ DE450 vs. kernel 2.1.79 | | Date | Sat, 24 Jan 1998 23:35:20 -0800 | | From | Stephen Williams <> |
| |
So I compiled a kernel and managed to boot it. Grand, but when I tried to boot it again, I can't. It is true that when i reboot from MILO I use the command ether=0,0,eth1 whereas the first time I did not. The following is a dmesg dump from a successful 2.0.32 dump. Could it be there is a problem with the driver for the DE450 ethernet board?
--Steve
Command line: bootdevice=sda2 bootfile=vmlinux-2.0.32.gz ether=0,0,eth1 Alpha PCI BIOS32 revision 0.03 Probing PCI hardware. SMC FDC37C93X Ultra I/O Controller found @ 0x370 Console: 16 point font, 400 scans Console: colour VGA+ 80x25, 1 virtual console (max 63) Calibrating delay loop.. ok - 497.03 BogoMIPS Memory: 61872k available Swansea University Computer Society NET3.035 for Linux 2.0 NET3: Unix domain sockets 0.13 for Linux NET3.035. Swansea University Computer Society TCP/IP for NET3.034 IP Protocols: IGMP, ICMP, UDP, TCP Linux version 2.0.32 (root@icarus.icarus.com) (gcc version 2.7.2.3) #2 Fri Jan 16 23:16:24 PST 1998 Starting kswapd v 1.4.2.2 Serial driver version 4.13 with no serial options enabled tty00 at 0x03f8 (irq = 4) is a 16550A tty01 at 0x02f8 (irq = 3) is a 16550A PS/2 auxiliary pointing device detected -- driver installed. Ramdisk driver initialized : 16 ramdisks of 4096K size hda: WDC AC22100H, 2014MB w/128kB Cache, CHS=4092/16/63 hdb: FX120T, ATAPI CDROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Floppy drive(s): fd0 is 2.88M FDC 0 is a post-1991 82077 aic7xxx: <Adaptec AHA-294X Ultra SCSI host adapter> at PCI 6 aic7xxx: Warning - detected auto-termination. Please verify driver detected settings and use manual termination if necessary. aic7xxx: BIOS enabled, IO Port 0x8800, IO Mem 0xc000000, IRQ 16, Revision B aic7xxx: Wide Channel, SCSI ID 7, 16/16 SCBs, QFull 16, QMask 0x1f scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 4.1/3.2 scsi : 1 host. scsi0: Scanning channel A for devices. Vendor: Quantum Model: XP32150W Rev: L912 Type: Direct-Access ANSI SCSI revision: 02 Detected scsi disk sda at scsi0, channel 0, id 0, lun 0 scsi0: Sending SDTR!! Vendor: SEAGATE Model: ST15230N Rev: 0058 Type: Direct-Access ANSI SCSI revision: 02 Detected scsi disk sdb at scsi0, channel 0, id 1, lun 0 scsi0: Target 2, channel A, refusing WIDE negotiation; using 8 bit transfers. Vendor: MATSHITA Model: PD-1 LF-1001 Rev: A105 Type: Optical Device ANSI SCSI revision: 02 Detected scsi removable disk sdc at scsi0, channel 0, id 2, lun 0 Vendor: MATSHITA Model: PD-1 LF-1001 Rev: A105 Type: CD-ROM ANSI SCSI revision: 02 Detected scsi CD-ROM sr0 at scsi0, channel 0, id 2, lun 1 scsi : detected 1 SCSI cdrom 3 SCSI disks total. SCSI device sda: hdwr sector= 512 bytes. Sectors= 4406960 [2151 MB] [2.2 GB] SCSI device sdb: hdwr sector= 512 bytes. Sectors= 8386733 [4095 MB] [4.1 GB] SCSI device sdc: hdwr sector= 512 bytes. Sectors= 1298496 [634 MB] [0.6 GB] sdc: Write Protect is off eth0: 3c509 at 0x300 tag 1, 10baseT port, address 00 60 97 1a e3 ab, IRQ 11. 3c509.c:1.12 6/4/97 becker@cesdis.gsfc.nasa.gov eth1: DE450-CA at 0x9000 (PCI bus 0, device 5), h/w address 00:00:f8:02:04:34, and requires IRQ18 (provided by PCI BIOS). Partition check: sda: sda1 sda2 sda3 sda4 < sda5 sda6 > sdb: sdb1 sdb2 sdb3 sdb4 sdc: sdc1 hda: hda1 hda2 < hda5 hda6 > VFS: Mounted root (ext2 filesystem) readonly. Adding Swap: 80312k swap-space (priority -1) Adding Swap: 134792k swap-space (priority -2) eth0: Setting Rx mode to 1 addresses.
|  |